Fedders CH18ABD1の取扱説明書

デバイスFedders CH18ABD1の取扱説明書

デバイス: Fedders CH18ABD1
カテゴリ: ヒートポンプ
メーカー: Fedders
サイズ: 0.86 MB
追加した日付: 4/19/2014
ページ数: 8
説明書を印刷

ダウンロード

使い方は?

私たちの目的は、皆様方にデバイスFedders CH18ABD1の取扱説明書に含まれたコンテンツを可能な限り早く提供することです。オンラインプレビューを使用すると、Fedders CH18ABD1に関してあなたが抱えている問題に対する解決策の内容が素早く表示されます。

便宜上

説明書Fedders CH18ABD1をこちらのサイトで閲覧するのに不都合がある場合は、2つの解決策があります:

  • フルスクリーン表示 – 説明書を(お使いのコンピュータにダウンロードすることなく)便利に表示させるには、フルスクリーン表示モードをご使用ください。説明書Fedders CH18ABD1のフルスクリーン表示を起動するには、全画面表示ボタンを押してください。
  • コンピュータにダウンロード - Fedders CH18ABD1の説明書をお使いのコンピュータにダウンロードし、ご自身のコレクションに加えることもできます。デバイス上のスペースを無駄にしたくない場合は、いつでもManualsBaseサイトでダウンロードすることもできます。
Fedders CH18ABD1 取扱説明書 - Online PDF
Advertisement
« Page 1 of 8 »
Advertisement
印刷版

多くの人々は画面表示ではなく印刷された説明書を読むほうを好みます。説明書を印刷するオプションも提供されており、上記のリンクをクリックすることによりそれを利用できます - 説明書を印刷。説明書Fedders CH18ABD1を全部印刷する必要はなく、選択したページだけを印刷できます。紙を節約しましょう。

要旨

次のページにある説明書Fedders CH18ABD1の内容のプレビューは、以下にあります。次のページにある説明書の内容をすぐに表示したい場合は、こちらをご利用ください。

内容要旨
ページ1に含まれる内容の要旨


Installation, Operation and Maintenance
1.5 Through 5 Ton
Heat Pump
TABLE OF CONTENTS
INTRODUCTION..............................................................................1
NOTES TO INSTALLER ....................................................................1
CODES ............................................................................................1
RECOGNIZE SAFETY SYMBOLS, WORDS AND LABELS ................1
INSPECTION AND UNPACKING.............................................

ページ2に含まれる内容の要旨

Installation and service personnel are required by some locales INTRODUCTION to be licensed. Persons not qualified SHALL NOT install this You have made a major investment in a fine piece of equipment nor interpret these instructions. equipment. Keep your investment sound by reading these This installation and maintenance manual is provided to ensure instructions before installing this unit. This will ensure that the proper installation and the most satisfactory performance of the full potential

ページ3に含まれる内容の要旨

Proximity to Evaporator INSTALLATION Locating the condenser as close as possible to the evaporator Condensing Unit Location will increase the system capacities by reducing the line set refrigerant pressure drop, and will make the system less The condensing unit should be located outdoors as close as susceptible to liquid migrations due to less refrigerant charge. possible to the evaporator. Consider the following factors: Clearances The air inlet should be located at least 12" from a wall or oth

ページ4に含まれる内容の要旨

Evacuation Electrical Connections (cont.) The outdoor unit is factory charged. Evacuation is necessary Connect control wiring on the uncharged portions of the total system. Purge the 1. Route 24 volt control wires through control wiring grommet system with dry nitrogen. Then connect a vacuum pump and and connect leads to control wiring. a vacuum gage capable of accurately measuring below 2. Use No. 18 AWG color coded, insulated wire. If thermostat is 1,000 microns vacuum depth. The deep vacuum m

ページ5に含まれる内容の要旨

20’ 10’ MAX 3”MIN. Precautions CONNECT REFRIGERANT PIPING Refer to the chart below for the minimum recommended tube The following should be followed when installing refrigerant outside diameter sizes on liquid and suction lines. Ensure that piping. Comply with all local, state, and federal codes and/or vapor and liquid tube diameters are appropriate for unit regulations pertaining to this type of equipment and its capacity. Run refrigerant tubes as directly as possible by installation. avoiding

ページ6に含まれる内容の要旨

Model SUB-COOLING CHARGING FINAL CHECKS FOR INSTALLER For proper sub-cooling readings, a standard high side gauge is 1. Ensure that all wiring is routed away from tubing and sheet required for pressure readings. metal edges to prevent rub-through or wire pinching. Use the charts below to determine the required sub-cooling value. 2. Ensure that all wiring and tubing is secure in unit before adding panels and covers. INSTRUCTIONS 3.Tighten service valve stem caps to 1/12 turn past 1. Measure the

ページ7に含まれる内容の要旨

DEFROST OPERATION MAINTENANCE INSTRUCTIONS For continuing high performance and to minimize possible The heat pump has a control system designed to defrost the equipment failure, periodic maintenance must be performed on outdoor coil by warming it up to keep it clear of ice and this equipment. Frequency of maintenance may vary depending operating efficiently. When the temperature drops below 40°F, the control system will sense that conditions are right for the upon geographic areas, such as coast

ページ8に含まれる内容の要旨

Model C10 & LIMITED WARRANTY Limited Five Year Warranty: This Warranty Does Not Cover Damage Caused By: Fedders will provide a replacement part or component • Improper installation that proves to be defective in material or workmanship. • Misuse of equipment Warranty Limitations: • Negligent servicing • Limited Warranty does not include allowances for labor • Improper applications or travel expense connected with the installation of • Preventative maintenance parts, so furnished in this


類似の説明書
# 取扱説明書 カテゴリ ダウンロード
1 Fedders C12 取扱説明書 ヒートポンプ 0
2 Fedders CH1048CBD3VF 取扱説明書 ヒートポンプ 0
3 Fedders CH1060CBD1VF 取扱説明書 ヒートポンプ 0
4 Fedders CH1042CBD1VF 取扱説明書 ヒートポンプ 0
5 Fedders CH1048CBD4VF 取扱説明書 ヒートポンプ 0
6 Fedders CH1060CBD4VF 取扱説明書 ヒートポンプ 1
7 Fedders CH1048CBD1VF 取扱説明書 ヒートポンプ 0
8 Fedders CH18ABD1VF 取扱説明書 ヒートポンプ 0
9 Fedders CH1060CBD3VF 取扱説明書 ヒートポンプ 0
10 Fedders CH12 取扱説明書 ヒートポンプ 0
11 Fedders CH36ACD1VF 取扱説明書 ヒートポンプ 0
12 Fedders CH24ACD1VF 取扱説明書 ヒートポンプ 0
13 Fedders CH30ACD1VF 取扱説明書 ヒートポンプ 0
14 Fedders CH42ACD1VF 取扱説明書 ヒートポンプ 0
15 Fedders CH48ACD1VF 取扱説明書 ヒートポンプ 1
16 Edelbrock 15005 取扱説明書 ヒートポンプ 0
17 A.O. Smith AH 取扱説明書 ヒートポンプ 2
18 ACS 882.00217.00 取扱説明書 ヒートポンプ 1
19 A.O. Smith AHD 290 取扱説明書 ヒートポンプ 3
20 AC International SELF-PRIMING CENTRIFUGAL PUMPS 取扱説明書 ヒートポンプ 5