ページ1に含まれる内容の要旨
READ AND SAVE THESE INSTRUCTIONS
™
MARIOL PORTICO
Wet Location
Model No.
Ceiling Fan
CF690CK00
Owner's Manual
CF690ORB00
Net Weight: 24.2 Lbs.
ENERGY STAR
LIMITED WARRANTY
What The Warranty Covers:
This warranty covers the motor and the other components and accessories of your Emerson ceiling fan against all defects in workmanship and materials.
You must be the original purchaser or user of the product to be covered.
What The Period Of Coverage Is:
As it applies to the motor, this warranty will
ページ2に含まれる内容の要旨
! WARNING WARNING: To avoid fire, shock, and serious personal injury, follow these instructions. Safety Instructions 1. Read your owner’s manual carefully and keep it for future reference. 2. Before servicing or cleaning unit, switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a warning device, such as a tag, to the service panel. 3. Be careful of
ページ3に含まれる内容の要旨
THIS FAN IS SUITABLE FOR WET LOCATIONS SUCH AS PORCHES, PATIOS, AND DECKS. This Manual Is Designed to Make it as Easy as Possible for You to Assemble, Install, Operate and Maintain Your Ceiling Fan Installed Wire Length Wire Size A.W.G. Tools Needed for Assembly Up to 50 ft. 14 One Phillips head screwdriver One stepladder 50-100 ft. 12 One 1/4” blade screwdriver One wire stripper One 5/16” open end wrench, or pliers Three wire connectors (supplied) ! WARNING MATERIALS Before assembly your ceilin
ページ4に含まれる内容の要旨
How to Put Your Ceiling Fan Together 1. Remove the hanger ball by loosening the setscrew 4. Make sure the grommet is properly installed in the in the hanger ball until the ball falls freely down the coupling cover, then slide the coupling cover on the downrod (Figure 1). Remove the pin from the downrod until it rests on the motor housing. Place downrod, then remove the hanger ball. Retain the the ceiling cover over the downrod. Be sure that pin and hanger ball for reinstallation in step 5. the c
ページ5に含まれる内容の要旨
BRACKET SWITCH ! WARNING HOUSING ASSEMBLY WITH RUBBER COVER REINSTALL ONE To reduce the risk of personal injury, do not bend the SERRATED HEAD blade flange when installing the blade flanges, SCREW balancing the blades or cleaning the fan. Do not insert foreign objects in between rotating fan blades. TIGHTEN TWO PAN HEAD SCREWS M5 x 6 WASHER HEAD SCREW (3) MOUNTING RIB LINE SCREWS (4) (THIS SIDE OF BLADE UP) ADAPTOR PLATE Figure 7 FAN BLADE 14. Engage the connector of the switch housing BLADE
ページ6に含まれる内容の要旨
Electrical Requirements ! WARNING To reduce the risk of fire, electric shock, or personal Your new ceiling fan will require a grounded electrical injury, mount fan to outlet box marked “Acceptable supply line of 120 volts AC, 60 Hz, 15 amp circuit. for Fan Support”, and use screws supplied with outlet box. Most outlet boxes commonly used for support of light fixtures are not acceptable for fan ! WARNING support and may need to be replaced. Consult a qualified electrician in in doubt. To reduce t
ページ7に含まれる内容の要旨
How to Wire ! WARNING Your Ceiling Fan Check to see that all connections are tight, including ground, and that no bare wire is visible at the wire connectors, except for the ground wire. Do not If you feel that you do not have enough electrical operate fan until blades are in place. Noise and fan wiring knowledge or experience, have your fan damage could result. installed by a licensed electrician. 3. Screw the two threaded studs (supplied) into the ! WARNING tapped holes in the hanger bracket (
ページ8に含まれる内容の要旨
Using Your Ceiling Fan Energy Efficient Use of Ceiling Fans 1. Restore electrical power to the outlet box by turning the electricity on at the main fuse box. Ceiling fan performance and energy savings rely 2. Check the operation of the fan by gently pulling on heavily on the proper installation and use of the ceil- the pull chain switch. ing fan. Here are a few tips to ensure quality and product performance. 3. All fans are shipped from the factory with the reversing switch positioned to the “le
ページ9に含まれる内容の要旨
Maintenance Abrasive cleaning agents are not required and should IMPORTANT CARE INSTRUCTIONS be avoided to prevent damage to finish. for your Ceiling Fan Periodic cleaning of your new ceiling fan is the only maintenance that is needed. ! WARNING When cleaning, use only a soft brush or lint free cloth Do not use water when cleaning your ceiling fan. It to avoid scratching the finish. could damage the motor or the blades and create the possibility of an electrical shock. Accessories 1. Ceiling Fan
ページ10に含まれる内容の要旨
Repair Parts 2 1 3 5 6 4 7 8 9 10 11 17 18 19 12 20 13 14 15 16 Before discarding packaging material, be certain all parts have been removed. HOW TO ORDER REPAIR PARTS WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWING INFORMATION: • PART NUMBER • NAME OF ITEM • PART DESCRIPTION • MODEL NUMBER The model number of your Fan will be found on a label attached to the top housing. For repair parts, phone 1-800-654-3545. 10
ページ11に含まれる内容の要旨
Repair Parts Listing Part Numbers Key Model No. Model No. No. Description CF690CK00 CF690ORB00 * Hanger Ball Assembly, 761655-23 761655-32 Consisting of: 1 Hanger Bracket — — 2 Hanger Ball — — 3 Downrod — — * Parts Bag Containing: 763234 763234-1 4 Wire Connector (3) — — 5 Threaded Stud (2) — — 7 Lockwasher (2) — — 8 Knurled Knob (2) — — 10 Pin, Clevis — — 11 Clip, Hairpin — — 15 Wood Pendant — — 16 Coupling — — 17 Screw, Blade M5 x 6 Washer Head (16) — — 20 Screw, Flange M6 x 14 with Lockwashe
ページ12に含まれる内容の要旨
Air Comfort Products DIVISION OF EMERSON ELECTRIC CO. 8100 W. Florissant ¥ St. Louis, MO 63136 Part No. F40BP73310000 Printed in China 10/06 Form No. BP7331
