ページ1に含まれる内容の要旨
AK2000,AK6000,AK9800
ページ2に含まれる内容の要旨
AK2000,AK6000,AK9800
ページ3に含まれる内容の要旨
PRODUCT OVERVIEW 1 HURRICANE SERIES Model number: AK2000, 2036 QuattroVent Air Curtain Dual “Thrust-Fore" Self Clean Blowers Digital Touch Pad Controls Clock, Timer, 3 stage Delay Shutoff. CYCLONE SERIES Model number: AK6000, 6036, 6042, 6048 Dual “Thrust-Fore" Self Clean Blowers Independent Rocker Controls w/ High, Low speed 3 Way convertible ducting option WHIRLWIND SERIES Model number: AK9800 Dual Self Clean Blowers Independent Rocker Controls w/ High, Low speed Slim Line Design 3 Overview
ページ4に含まれる内容の要旨
CONTROLS 2 HURRICANE SERIES 14 13 12 11 10 3 hr HI LO HI LO 2 12:01 4 5 1 DELAY min FAN-L FAN-R ON-OFF OFF 67 8 9 Controls Overview 1. Set Time 8. Right Blower: On-High-Low-Off 2. Digital Display 9. Operations: On-Off 3. Set Hours 10. Right Blower Low Speed Indicator 4. Set Minutes 11. Right Blower High Speed Indicator 5. Set Timed Delay Shut Off 12. Left Blower Low Speed Indicator 6. Light On-Off 13. Left Blower High Speed Indicator 7. Left Blower: On-High-Low-Off 14. Delay Off Indicator Settin
ページ5に含まれる内容の要旨
CONTROLS 3 Blower Controls You can simultaneously turn On the light and press: both blowers on Hi speed by simply pressing to turn light and both ON-OFF blowers on Hi "On/Off" once. During this time, you can select blowers and or turn individual blowers FAN-R FAN-L On/Off and select Hi/Lo speed speed as indicated by pressing the "Fan-L" and "Fan-R" button. press again to turn all Note: ON-OFF operations Off The third press on the "Fan-L" and "Fan-R" button will turn blower Off the selected
ページ6に含まれる内容の要旨
CONTROLS 4 Setting Timer (Alarm) Press "hr" and "min" button to set desired timer press: countdown. hr Once timer is set, countdown will start in 7 hr seconds as delay indicator light flashes. min 1:04 DELAY min OFF When countdown reaches 0, 10 short beeps will sound. set "hr" & "min" for timer countdown alarm will sound at end of timer To cancel timer after setting, press "On/Off" button to terminate all operations and restart. Note: Timer function cannot be operated simultaneously with th
ページ7に含まれる内容の要旨
MAINTENANCE 5 Self Clean Feature All Zephyr Range Hoods are filter-less and are designed with a self clean feature. The centrifugal blower system automatically liquefies grease accumulated in its internal housing. All systems are equipped with dishwasher safe grease containers for its self clean function. Grease and residue from cooking are often automatically liquefied and can accumulate in the containers from everyday use. Nevertheless, grease from cooking could also dry and adhered in it
ページ8に含まれる内容の要旨
MAINTENANCE 6 With nozzle on ‘spray’, squirt ‘409’ detergent directly onto blower blades 30-35 times. Repeat with second blower. Allow self cleaning to run for 5 minutes before switching off. (If desired, spray water to rinse off detergent after completion of the cleaning cycle and run for another few minutes) Remove residue containers by gently sliding out with both hands. Clean in dishwasher under normal wash cycle. Hurricane Series: Remove light shield by turning counter- clockwise.
ページ9に含まれる内容の要旨
MAINTENANCE 7 QuattroVent Channels The QuattroVent Air-Curtain channels are adjoined to its two main blowers and share the same internal housing. No further cleaning is required after the self clean is completed. Clean residue around the channels surface with ‘409’ and a cotton cloth regularly. Surface Maintenance Clean all surface residue with ‘409’ or mild detergent and wipe with a cotton cloth. Stainless steel surface could further be polished with any stainless steel polish or glass cl
ページ10に含まれる内容の要旨
INSTALLATION 8 WARNING Installation of this product is intended for qualified installers, service technicians, or persons with similar qualified background. DO NOT attempt to install this appliance yourself. Injury could result form installing the unit due to lack of appropriate electrical knowledge and technical background. Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage and the warranty on the product automatically becomes void.
ページ11に含まれる内容の要旨
INSTALLATION 9 DUCT OPENING Wall 2-1/2” Rear Front 3-1/4 x 10” 4-1/2” (A) 6” Rear 7” Front Wall Cut Out Size (A): Hurricane 10-1/2“ Cyclone 10-1/2” Whirlwind 8-1/2” CLEARANCES Minimum clearance above range should be no less than 18“ from the range surface to the range hood’s base. Maximum height are recommended not to exceed 30” for maximum efficiency. Net width on all models are call out width less 1/4”. Call Out Size Net Width net width 30“ 29-3/4” 36“ 35-3/4” 42“ 41-3/4” MIN. 18” MAX
ページ12に含まれる内容の要旨
INSTALLATION 10 STEP 1 STEP 2 1. Remove all contents from box 1. Locate electrical connection box inside 2. Unscrew and remove bottom grease splash shield 2. Unscrew cover to reveal wiring STEP 3 STEP 4 1. Locate electrical connection box knock out from left 1. Cut out cabinet base opening if necessary. Refer rear of hood and pry open with screwdriver cut out dimensions previous page. STEP 5 STEP 6 (also refer notes on pg. 16) 1. Reinforce cabinet base with 1x2 wood strips if 1. Install dampe
ページ13に含まれる内容の要旨
INSTALLATION 11 STEP 7 STEP 8 1. Lift hood to bottom of cabinet 1. Support hood to place, fasten both rear with screws and washers provided. STEP 9 (also refer notes on pg. 16) STEP 10 1. Fasten front of hood. Level all sides and adjust 1. Drill out cabinet base through electrical box with accordingly.** 3/4" boring bit. STEP 11 STEP 12 (also refer notes pg. 16) 1. Connect both wires (blk) on hood to either power 1. Pull electrical supply wire through drill out or use supply (blk or wht).
ページ14に含まれる内容の要旨
INSTALLATION 12 STEP 13 STEP 14 1. Reinstall electrical box cover. 1. Reinstall bottom splash shield by first fastening 3 rear screws, (do not tighten all the way). STEP 15 STEP 16 1. Next, fasten the 3 front screws and begin tightening 1. Connect duct to opening, inspect and tape all joints all screws from rear to front. with approved aluminum or duct tape. STEP 17 STEP 18 1. Turn on electrical supply or plug into receptacles. 1. On Cyclone & Whirlwind models, be sure to pull both grease tub
ページ15に含まれる内容の要旨
INSTALLATION 13 CONVERTIBLE OPTIONS Cyclone series: AK6000, 6036, 6042, 6048 Zephyr’s Cyclone series are equipped with the option of a 6“ vertical discharge, 3-1/4x10” vertical discharge, or 3- 1/4x10” rear discharge. Additional accessories are provided to convert to either of the above discharge methods. Convertible Options Convertible Accessories Vertical discharge 6“ round 6“ round duct cap Vertical discharge 3-1/4 x 10“ Round to rectangular transition adaptor Horizontal rear discharge 3-1/4
ページ16に含まれる内容の要旨
INSTALLATION 14 3-1/4 x 10“ Rear Discharge 4. At rear of range hood, remove all screws on pre- 5. Remove top pre-mounted transition piece. Leave mounted rear rectangular cap and remove cap with attached gasket in its original place. gasket. 6. Remove 2 arch blocks through top opening. 7. Mount Starting Collar (provided) at rear discharge opening with gasket previously removed. Option 1: (for recessed cabinet base) Cap opening with 6“ cap provided OR, use option 2 if cabinet base is not r
ページ17に含まれる内容の要旨
INSTALLATION 15 3-1/4 x 10“ Rear Discharge Option 2: (for flush cabinet base) Mount rectangular cap (previously removed) on top of Mount rectangular transition piece at opening with transition adaptor. gasket as shown.
ページ18に含まれる内容の要旨
INSTALLATION 16 INSTALLATION NOTES Step 6: A damper (not included) should be installed to prevent back-draft where needed. A damper might also be required local codes in order to qualify for building inspections. You can purchase dampers from most hardware stores, or call our service line to order. When a damper is not installed, a starting collar is provided in order to increase and raise the duct opening clearance above the cabinet's base. Snap the adaptor's smaller end to hood's duct o
ページ19に含まれる内容の要旨
TROUBLE SHOOTING 17 1. Upon completion of installation, Check if unit has been plugged in, make sure that all power nothing works. has been turned back on and all electrical wiring are properly connected. 2. Light is on but blowers are not Blower blade unit might have been mounted too low and turning at all or seems to be scraping on scraping the bottom or jammed. Loosen hex screw on something. blade unit and adjust to proper height. 3. When blowers are on, something There might have been
ページ20に含まれる内容の要旨
TROUBLE SHOOTING 18 Use a damper type sidewall cap. Reduce the number of elbows and length of duct work. Check if all joints are properly connected, sealed and taped. 11. Cooking fumes and smoke dissipates Check if unit is installed at the recommended height before it reaches the blower. (page 9). The range hood should also be able to cover the entire cooking area from left to right and most areas from rear to front. Open doors and windows might also distract air flow before it reaches the
