ページ1に含まれる内容の要旨
READ AND SAVE THESE INSTRUCTIONS
®
™
ZURICH
Model No.
CF935OB 00 CF935TG 00
Ceiling Fan
CF935AB 00 CF935PW 00
Owner's Manual
CF935BQ 00 CF935PB 00
CF935HTW 00
Net Weight: 21.0 Lbs.
LIMITED WARRANTY
What The Warranty Covers:
This warranty covers the motor and the other components and accessories of your Emerson ceiling fan against all defects in workmanship and materials.
You must be the original purchaser or user of the product to be covered.
What The Period Of Coverage Is:
As it applies to the
ページ2に含まれる内容の要旨
! WARNING WARNING: To avoid fire, shock, and serious personal injury, follow these instructions. Safety Instructions 1. Read your owner’s manual carefully and keep it for future reference. 2. Before servicing or cleaning unit, switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a warning device, such as a tag, to the service panel. 3. Be careful of
ページ3に含まれる内容の要旨
This Manual Is Designed to Make it as Easy as Possible for You to Assemble, Install, Operate and Maintain Your Ceiling Fan Installed Wire Length Wire Size A.W.G. Tools Needed for Assembly Up to 50 ft. 14 One Phillips head screwdriver One stepladder 50-100 ft. 12 One 1/4” blade screwdriver One wire stripper Three wire connectors (supplied). ! WARNING MATERIALS Before assembly your ceiling fan, refer to section on proper method of wiring your fan (page 6). If you feel Wiring outlet box and box con
ページ4に含まれる内容の要旨
How to Put Your Ceiling Fan Together 1. Remove the hanger ball by loosening the setscrew 5. Make sure the grommet is properly installed in the in the hanger ball until the ball falls freely down the coupling cover, then slide the coupling cover on the downrod (Figure 1). Remove the pin from the downrod until it rests on the motor housing. Place downrod, then remove the hanger ball. Retain the the ceiling cover over the downrod. Be sure that pin and hanger ball for reinstallation in step 5. the c
ページ5に含まれる内容の要旨
! WARNING SWITCH HOUSING ASSEMBLY To reduce the risk of personal injury, do not bend the blade flange when installing the blade flanges, balancing the blades or cleaning the fan. Do not insert foreign objects in between rotating fan blades. SWITCH HOUSING CONNECTOR 3/16-24 x 1/4" SLOTTED MOTOR PHILLIPS SCREWS (3) CONNECTOR SWITCH HOUSING BLADE WASHERS (3) MOUNTING SCREW (3) Figure 7 13.Remove the three switch housing mounting screws (Figure 7) from the switch housing plate. FAN BLADE Position t
ページ6に含まれる内容の要旨
How to Hang Your Ceiling Fan OUTLET ! WARNING BOX The fan must be hung with at least 7' of clearance from floor to blades (Figure 9). CEILING TWO SCREWS SUPPLIED WITH HANGER OUTLET BOX BRACKET TAB Figure 10 AT LEAST Figure 2 7' 2. Carefully lift the fan and seat the hanger ball/ downrod assembly on the hanger bracket that was FLOOR just attached to the outlet box (Figure 11). Be sure Figure 9 the groove in the ball is lined up with tab on the hanger bracket (Figure 10). ! WARNING ! WARNING The o
ページ7に含まれる内容の要旨
BLACK AND BLUE 5. Secure the ceiling cover in place by sliding lockwash- FAN WIRES GROUND ers over the threaded studs and installing the two WIRE knurled knobs (supplied). (Figure 13.) Tighten the LISTED knurled knobs securely until the ceiling cover fits WHITE SUPPLY WIRE (NEUTRAL) CONNECTOR (3) snugly against the ceiling and the hole in the ceiling cover is clear of the downrod. Your fan is now wired to NOTE: CEILING COVER be turned on and off from the fan switch. OMITTED FOR CLARITY. GREEN WI
ページ8に含まれる内容の要旨
! WARNING: FOR YOUR OWN SAFETY TURN OFF POWER AT FUSE BOX OR CIRCUIT BREAKER BEFORE TROUBLE SHOOTING YOUR FAN. Trouble Shooting TROUBLE PROBABLE CAUSE SUGGESTED REMEDY 1. Fan will not start. 1. Fuse or circuit breaker blown. 1. Check main and branch circuit fuses or circuit breakers. 2. Loose power line connections to the fan, or loose 2. Check line wire connections to fan and switch switch wire switch wire connections in the switch housing. connections in the switch housing.wire connections in
