ページ1に含まれる内容の要旨
READ AND SAVE THESE INSTRUCTIONS
Model No.
CF770AW01
CF770BC01
CF770BS01
CF770OB01
®
CF770ORB01
CF770TG01
MONTEREY
CF770WW01
Ceiling Fan
Net Weight: 19.8 Lbs.
Owner's Manual
LIMITED WARRANTY
What The Warranty Covers:
This warranty covers the motor and the other components and accessories of your Emerson ceiling fan against all defects in workmanship and materials.
You must be the original purchaser or user of the product to be covered.
What The Period Of Coverage Is:
As it applies to the motor,
ページ2に含まれる内容の要旨
WARNING ! WARNING: To avoid fire, shock, and serious personal injury, follow these instructions. Safety Instructions 1. Read your owner’s manual carefully and keep it for future reference. 2. Before servicing or cleaning unit, switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a warning device, such as a tag, to the service panel. 3. Be careful of
ページ3に含まれる内容の要旨
This Manual Is Designed to Make it as Easy as Possible for You to Assemble, Install, Operate and Maintain Your Ceiling Fan Tools Needed for Assembly One Phillips head screwdriver One stepladder Installed Wire Length Wire Size A.W.G. One 1/4” blade screwdriver One wire stripper Up to 50 ft. 14 One 5/16” open end wrench, or pliers 50-100 ft. 12 Three wire connectors (supplied). ! WARNING MATERIALS Before assembly your ceiling fan, refer to section on Wiring outlet box and box connectors must be of
ページ4に含まれる内容の要旨
How to Put Your Ceiling Fan Together 1. Remove the hanger ball by loosening the setscrew 4. Make sure the grommet is properly installed in the in the hanger ball until the ball falls freely down the coupling cover, then slide the coupling cover on the downrod (Figure 1). Remove the pin from the downrod until it rests on the motor housing. Place downrod, then remove the hanger ball. Retain the the ceiling cover over the downrod. Be sure that pin and hanger ball for reinstallation in step 5. the c
ページ5に含まれる内容の要旨
10. Engage the connector of the switch housing ! WARNING assembly with the motor connector (Figure 7). The two connectors are keyed and color-coded To reduce the risk of personal injury, do not bend the and must be mated correctly (color-to-color) blade flange when installing the blade flanges, before they can be engaged. Make sure the con- balancing the blades or cleaning the fan. Do not nector latch closes properly. insert foreign objects in between rotating fan blades. 3/16-24 x 1/4" SLOTTED
ページ6に含まれる内容の要旨
NOTE: CEILING COVER, How to Hang Your SUPPLY WIRES AND OUTLET FAN WIRES OMITTED BOX Ceiling Fan FOR CLARITY. ! WARNING The fan must be hung with at least 7' of clearance from floor to blades (Figure 9). HANGER BRACKET CEILING HANGER BALL/ Figure 11 DOWNROD ASSEMBLY WARNING ! To avoid possible fire or shock, do not pinch wires AT LEAST 7' between the hanger ball/downrod assembly and hanger bracket. Figure 9 FLOOR ! WARNING How to Wire Your The outlet box and joist must be securely mounted Ceilin
ページ7に含まれる内容の要旨
BLACK AND BLUE 5. Secure the ceiling cover in place by sliding lock- FAN WIRES GROUND washers over the threaded studs and installing the WIRE two knurled knobs (supplied). (Figure 13.) Tighten LISTED the knurled knobs securely until the ceiling cover WHITE SUPPLY WIRE (NEUTRAL) CONNECTOR (3) fits snugly against the ceiling and the hole in the ceiling cover is clear of the downrod. Your fan is now wired to be turned on and off from the fan switch. GREEN WIRE (GROUND) FROM WHITE FAN HANGER BRACKET
ページ8に含まれる内容の要旨
! WARNING: FOR YOUR OWN SAFETY TURN OFF POWER AT FUSE BOX OR CIRCUIT BREAKER BEFORE TROUBLE SHOOTING YOUR FAN. Trouble Shooting TROUBLE PROBABLE CAUSE SUGGESTED REMEDY 1. Fan will not start. 1. Fuse or circuit breaker blown. 1. Check main and branch circuit fuses or circuit breakers. 2. Loose power line connections to the fan, or loose 2. Check line wire connections to fan and switch switch wire switch wire connections in the switch housing. connections in the switch housing.wire connections in
