ページ1に含まれる内容の要旨
ページ2に含まれる内容の要旨
CONTENTS INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 MOUNTING RECOMMENDATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 FAN INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 CONTROL FEATURES: VERSA•TOUCH OPERATION
ページ3に含まれる内容の要旨
MOUNTING RECOMMENDATIONS Before mounting your Casablanca fan, read the following helpful recommendations. The location of the fan, air circulation, and fan size are all important factors to consider before installation. Location Ceiling fans have practical uses in almost every room in your home. We suggest you follow these mount- ing recommendations as you decide where to install your Casablanca fan. • For safety reasons, the fan blades must be a minimum of 7′ above the floor. • Do not locate th
ページ4に含まれる内容の要旨
™ S3 INSTALLATION INSTRUCTIONS Unpacking: Before assembling and installing your ceiling fan, remove all parts from the shipping cartons and check them against the parts listed here. Before discarding packaging material, be certain that all parts have been removed. WORK BENCH SETUP Setup. Remove the bottom foam from the box and place the fan rightside up in the foam. This protects the lamp socket during assembly. NOTE: If this is the second Versa•Touch fan in- stalled in the same area, one of th
ページ5に含まれる内容の要旨
CEILING HARDWARE ADDITIONAL HARDWARE 1 2 / ″ x 8-32 ROUND HEAD 4 SCREWS (2) CROSSBAR WIRE NUT (4) 1″ x 8-32 ROUND MOUNTING FLAT WASHER (2) HEAD SCREWS (2) BRACKET GETTING STARTED Installing a New Ceiling Fixture Outlet Box Using Existing Ceiling Fixture Outlet Box If you do not have an existing fixture located where you wish After turning the power OFF at its source (either circuit breaker to place your Casablanca fan, an approved ceiling fixture or fuse box), lower the old fixture and disconnec
ページ6に含まれる内容の要旨
™ S3 CANOPY INSTALLATION Step 2. Attach the canopy to the crossbar mount- CROSSBAR 1 ing bracket with three of the 8-32 x 2 /4″ long MOUNTING canopy screws and canopy lock washers. BRACKET Tighten the screw firmly by hand only. Note: On sloped ceilings, align the canopy opening towards the top or room peak. CANOPY CANOPY LOCK WASHER CANOPY SCREW BLADE HARDWARE BLADE SCREW METAL WASHER BLADE (3 PER BLADE) (3 PER BLADE) (3) BLADE INSTALLATION Step 3. Assemble the blades to the motor using the 3 bl
ページ7に含まれる内容の要旨
HANGING THE FAN Step 4. To hang the fan body in the canopy, hold the fan body firmly and in- sert the ball into the canopy opening. Check that no wires were pinched. Ro- tate the fan body until the slot in the nylon ball fits into the pin opposite the canopy opening. BALL NOTE: The fan weight is 23 pounds. PIN SLOT CANOPY ELECTRICAL CONNECTIONS Step 5a. Attach the fan wires to the ceiling fixture outlet box wiring by twisting the bare ends of the wires together and then securing with a wire nut.
ページ8に含まれる内容の要旨
™ S3 INSTALL BULB AND GLASS Step 9. Screw the 100 Watt Halogen bulb into the socket. Do not touch the glass bulb with your fingers–it is extremely important that the glass be clean. If it is touched, or dirty, clean carefully with a tissue. A dirty glass bulb will cause the bulb to fail almost immediately. IMPORTANT! When installing the halogen bulb, care- fully cut off the end of the plastic sleeve the bulb comes in and hold the bulb by the plastic sleeve to screw it into the socket. TABS HALO
ページ9に含まれる内容の要旨
R VERSA•TOUCH INSTALLATION W-42 CONTROL HOLDER DRYWALL SCREW WOOD SCREW 3 W-42 ANCHOR 6-32 X 1” SCREW 6-32 X /8” 9V BATTERY CONTROL 6-32 (2) 1” (2) (2) (2) VERSA•TOUCH CONTROL HOLDER INSTALLATION CAUTION! Do not use with wall dimmer. REMOVE TABS ROCKER STANDARD TYPE TOGGLE LIGHT SWITCH OUTER SWITCH MOUNTING INNER HOLES MOUNTING HOLES SWITCH SWITCH COVER COVER PLATE PLATE CONTROL Rocker Light Switch HOLDER Standard Light Switch Step 1. Break off the two tabs by pushing outward. Step 1. Remove
ページ10に含まれる内容の要旨
R VERSA•TOUCH OPERATION Fan Control SEND To start the fan. Press the selected speed button to run the fan at the desired speed. SIGNAL LO Low speed LED MED Medium speed HI High speed To turn off the fan. Press the FAN OFF button. Airflow Direction To reverse the airflow press the REVERSE button. Reverse operates at any speed whether fan is on or off. The fan returns to its set speed after reversing. Light Control Turn the light on or off independently from the fan by pressing the LIGHT button.
ページ11に含まれる内容の要旨
TROUBLESHOOTING Before Requesting Service: Please follow this troubleshooting guide before contacting your dealer for assistance. Caring for Finishes: For cleaning, a soft brush or lint-free cloth Never Lubricate this Fan! should be used to prevent scratching the finish. A vacuum cleaner The precision motor at the heart of your Casablanca fan features brush nozzle can remove heavier dust. Surface smudges or an accu- sealed bearings that are lubricated for life. Do not attempt to oil mulation of
ページ12に含まれる内容の要旨
761 CORPORATE CENTER DRIVE • POMONA, CA 91768 TOLL FREE: 888-CASA-1ST (227-2178) www.CasablancaFanCo.com ©COPYRIGHT 2000 CASABLANCA FAN COMPANY • U.S. PATENT PENDING PRINTED IN ROC