ページ1に含まれる内容の要旨
UNVENTED (VENT-FREE) UNIVERSAL FIREBOX
OWNER’S OPERATION AND INSTALLATION MANUAL
PFS
®
US
NON-CIRCULATINg MODELS
V32S, VFB32NC, V36S, V36SH, VFB36NC1, V42S, V42SH AND VFB42NC1
CIRCULATINg MODELS
V32, V36, V42, CUVF36C, VFB32C, VFB36C1, VFB42C1, V36H AND V42H
OUTSIDE AIR MODELS
V32A, V32AS, VFB32AC, VFB32ANC, V36A, V36AS, V36ASH,
V36AH, VFB36AC, VFB36ANC, V42A, V42AS, V42ASH, V42AH,
VFB42AC, VFB42ANC
WARNING: If the information in this manual is not
followed exactly, a fire or explosion may
ページ2に含まれる内容の要旨
TABLE OF CONTENTS Safety .................................................................. 2 Installation ........................................................... 9 Local Codes......................................................... 3 Replacement Parts ............................................ 18 Product Features ................................................. 4 Technical Service............................................... 18 Locating Firebox ........................................
ページ3に含まれる内容の要旨
SAFETy Continued 1. Do not use this firebox as a wood-burning f irebox front and screen become fireplace. Use only decorative unvented very hot when running heater. room heaters (log sets). Keep children and adults away 2. Do not add extra logs or ornaments such from hot surface to avoid burns as pine cones, vermiculite or rock wool. Using these added items can cause or clothing ignition. f irebox sooting. will remain hot for a time after 3. Do not use blower accessory with model shu
ページ4に含まれる内容の要旨
PRODUCT FEATURES opeRA tIoN ReFRActoR y bRIck lINeR This firebox is designed for use with approved Your firebox may feature a concrete refrac- ANSI Z21.11.2 decorative type unvented room tory brick liner. As with all concrete liners, heaters. (Physical size limitations apply. Refer this liner may develop slight cracks when to minimum firebox requirements supplied exposed to heat. These cracks will not affect with log heater.) It requires no outside vent- the performance of the fireplace or v
ページ5に含まれる内容の要旨
PRODUCT SPECIFICATIONS 32" models Outside Air Kit Location (Optional) 1 22 /2" 4" 1 8 / " 8 1 10 /2" 1 8 /8" 9 2 /16" 5/8" 7 3 /16" 1 15 25 /8" 8 /16" 1 29 /2" 7 34 /16" 1 3 19 /2" 36 /8" 11 16 /16" 13 2 / " 16 1 12 /4" Standoffs 1 4 /4" 5 8 /8" 1 36 /2" 1 Built-In 3 /2" Side 1 Nailing 32 /4" Flanges 7 18 /16" 15 3 14 /16" 16 /4" 9 1 1 / " 29 /2" 16 Square Gas Line 3 3 /8" 1 Access 8 /8" Holes 9 5 2 /16" 6 / " 16 1 2 /4" Electrical 6" 15 8 / " Front View 16 Access Hole 3 9 /4" Right Side View
ページ6に含まれる内容の要旨
PRODUCT SPECIFICATIONS Continued 36" ANd 42" models Note: If only one dimension is shown, the dimension is the same for both 36" and 42" mod- els. Outside Air Firebox Top View Kit Location (Optional) Right Side View 6 www.fmiproducts.com 108662-01L
ページ7に含まれる内容の要旨
AIR FOR COMBUSTION AND VENTILATION unusually t ight Construction WARNING: this heater shall The air that leaks around doors and windows not be installed in a room or may provide enough fresh air for combustion and ventilation. However, in buildings of un- space unless the required vol- usually tight construction, you must provide ume of indoor combustion air additional fresh air. is provided by the method de- unusually tight construction is defined as scribed in the National Fuel Gas con
ページ8に含まれる内容の要旨
AIR FOR COMBUSTION AND VENTILATION Continued 4. Compare the maximum Btu/Hr the space deteRmINING FResh-AIR FloW can support with the actual amount of Btu/ FoR heA teR locA tIoN Hr used. Determining if You Have a Confined or _________ Btu/Hr (maximum the space unconfined space can support) Use this work sheet to determine if you have _________ Btu/Hr (actual amount of a confined or unconfined space. Btu/Hr used) space: Includes the room in which you will Example: 63,360 Btu/Hr (max
ページ9に含まれる内容の要旨
AIR FOR COMBUSTION AND VENTILATION ventilation Air From outdoors veNtIlA tIoN AIR Provide extra fresh air by using ventilation Ventilation air from inside Building grills or ducts. You must provide two perma- This fresh air would come from an adjoining nent openings: one within 12" of the ceiling unconfined space. When ventilating to an and one within 12" of the floor. Connect these adjoining unconfined space, you must provide items directly to the outdoors or spaces open two permanent o
ページ10に含まれる内容の要旨
INSTALLATION Continued IMPORTANT: Vent-free gas log heaters add optional cabinet mantels (see Accessories, moisture to the air. Although this is beneficial, page 18) or as a built-in unit. Clearances are the installing firebox in rooms without enough same for either installation method. ventilation air may cause mildew to form from too much moisture. See Air for Combustion c Aut Io N: do not install and Ventilation, page 7. the firebox directly on carpet IMPORTANT: Make sure firebox is l
ページ11に含まれる内容の要旨
INSTALLATION t able 1 Not Ice : If your installation does rough opening Dimensions for not meet the minimum clear- built-in Installation ances shown, you must do one Front Width Depth Model (Inside to Inside) Height (Min.) of the following: 7 3 1 32" 34 /8" 36 /4" 16 / " 4 • raise the mantel to an accept- 1 1 3 2 2 4 36" 41 / " 40 / " 20 / " able height 5 1 5 8 2 8 42" 48 / " 44 / " 22 / " • remove the mantel u b Ilt-IN FIRebox INst AllA tIoN Built-in installation of this firebox involves Fi
ページ12に含まれる内容の要旨
INSTALLATION Continued IMPORTANT: If installing blower accessory IMPORTANT: Noncombustible materials such (circulating models with louvers only), see as brick, tile, etc. may overlap the front facing, Hard-Wiring Firebox, page 16. but should never cover any necessary open- ings like louvered slots. 3. Carefully set firebox in front of rough open- ing with back of firebox inside wall open- WARNING: do not allow ing. IMPORTANT: If installing a perimeter trim kit, see instructions included wit
ページ13に含まれる内容の要旨
INSTALLATION Continued INst AllING GAs lINe INst AllING optIoNAl bloWeR AccessoRIes notiCe: a qualified service per- son must connect heater to gas NotIce: the firebox identifica- supply. follow all local codes. tion label (including model num- ber, serial number, clearances, IMPORTANT: See Connecting to Gas Supply etc.) is located in the right side in your log set owner’s manual for details on screen pocket area on the front gas hookup. of the firebox. see figure 21, You may run the gas
ページ14に含まれる内容の要旨
INSTALLATION Continued Decide which way you intend to gain access model bk Installation into the bottom rear of the firebox to install 1. Attach the power cord to blower motor by the blower accessory. The lower front panel firmly pushing two female terminals at end can be removed easily by snapping out the of power cord onto two spade terminals front with a flat blade screwdriver. Use cau- on blower motor (see Figure 13). tion not to scratch any surfaces. Models with 2. Attach green ground
ページ15に含まれる内容の要旨
INSTALLATION Continued bracket (see Figure 14). Secure speed 14. Turn blower on and check for operation. control to bracket with lock nut by pushing Turn blower off by turning knob fully coun- and turning lock nut with pliers clockwise terclockwise before continuing. until it is tight against bracket. 15. Peel off backing paper and stick supplied 7. Remove knockout plug from louver panel wiring diagram decal on firebox bottom by pressing top and bottom retaining clips approximately 12" in f
ページ16に含まれる内容の要旨
INSTALLATION Continued 3. Using screws provided, fasten upper 12. Replace all panels and/or brick bottom flange of blower bracket to hearth pan and panel if previously removed. end flanges to leg stands (see Figure 16, ON/OFF 110/115 Panel Switch V .A.C. page 15). Black Hot Note: The wire assembly must be ar- Blower Blower Blower Motor Motor Motor Nuetral ranged in front of and away from fan No. 1 Black No. 2 No. 3 blades to reach power receptacle plug. 4. Remove 2 connectors from ON/
ページ17に含まれる内容の要旨
INSTALLATION Continued combustIoN AIR kIt model Ak4 INst AllING FIReplAce hood (oPtional) ANd scReeN The outside air kit may be installed on the 1. Attach hood to firebox using screws pro- left side of the fireplace only. The vent can be vided (see Figure 21). installed through any outside wall a minimum 2. Insert each rod through all rings located of three feet below fireplace termination cap. at top of screen. The handle to operate the damper door for the 3. Insert first rod into rear ho
ページ18に含まれる内容の要旨
REPLACEMENT PARTS Note: Use only original replacement parts. When calling, have ready: This will protect your warranty coverage for • your name parts replaced under warranty. • your address Contact authorized dealers of this product. • model and serial numbers of your heater If they can’t supply original replacement • how heater was malfunctioning part(s), call FMI PRODUCTS, LLC at 1-866- • purchase date 672-6040. Usually, we will ask you to return the part to the factory. TECHNICAL SERVICE
ページ19に含まれる内容の要旨
ACCESSORIES Continued mANtels FAce/louveR AN p el kIts 32" WAll mANtels smooth Faced - black W32tu - 32" Unfinished, Traditional sp32 - 32" Model, sp36 - 36" Model, W32to - 32" Oak Stain, Traditional sp42 - 42" Model W32co - 32" Oak Stain, Classic stamped louver - Black W32do - 32" Oak Stain, Dentil sl32 - 32" Model, sl36 - 36" Model, W32Go - 32" Oak Stain, Georgian sl42 - 42" Model 32" coRNeR mANtels Rolled - black c32tu - 32" Unfinished, Traditional Rl32 - 32" Model, Rl36 - 36" Model, c32to -
ページ20に含まれる内容の要旨
PARTS models v32, v32A, v32s, v32As, vF32 b c, vFb32Ac, vFb32Nc, vF32AN b c 22 21 20 23 18 19 17 16 28 15 29 10 25 9 7 26 5 24 27 4 11 14 3 12 6 13 2 8 1 20 www.fmiproducts.com 108662-01L
