ページ1に含まれる内容の要旨
Blue 4” Universal Thermostat with
Automatic Heat/Cool Changeover Option
Single Stage, Multi-Stage or Heat Pump
Installation and Operating Instructions for Model:
Save these instructions for future use!
Model Programming Choices
FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS
CAREFULLY BEFORE INSTALLING OR OPERATING
1F85-0477 7 Day 5/1/1 Day
THIS CONTROL COULD CAUSE PERSONAL INJURY
AND/OR PROPERTY DAMAGE.
APPLICATIONS
1F85-0477 Thermostat
THERMOSTAT APPLICATION GUIDE
Description
Heat Pump (No Au
ページ2に含まれる内容の要旨
INSTALLATION Figure 1 – Battery door shown open WARNING ! Thermostat installation and all components of the control system shall conform to Class II circuits per “AA” Alkaline Batteries the NEC code. Remove Old Thermostat A standard heat/cool thermostat consists of three basic parts: 1. The cover, which may be either a snap-on or hinge type. Thermostat can be powered by system AC power or Battery. 2. The base, which is removed by loosening all captive If is displayed, the thermostat is ba
ページ3に含まれる内容の要旨
WIRING DIAGRAMS Heat Pump Connections HEAT PUMP TYPE 1 (HP 1). Single stage compressor If you do not have a heat pump system, refer to figures 4-6. system; gas or electric backup. Refer to equipment manufacturers’ instructions for specific HEAT PUMP TYPE 2 (HP 2). Multi-stage compressor or two system wiring information. compressor system with gas or electric backup. You can configure the thermostat for use with the following After wiring, see INSTALLER CONFIGURATION section for heat pump sys
ページ4に含まれる内容の要旨
WIRING DIAGRAMS Figure 5 – Single Stage or Multi-Stage System (No Heat Pump) with Two Transformers Remove Jumper Wire Jumper between RH & RC L O/B W/E G RH RC Y Y2 W2 C System Single O Blower/ No Energized Constantly Stage 1 Circulator No Output Output in Cool Mode (SS1) Fan Energized Optional Fault 24 Volt 24 Volt Heat on Call for 24 Volt Indicator Cool Mode (Hot) (Hot) B Mode Cool (and (Com- (NOT 1st Stage Energized Constantly 1st Stage Heat Cool Heat if mon) USED) Cool Multi- in Heat, Off,
ページ5に含まれる内容の要旨
THERMOSTAT QUICK REFERENCE Home Screen Description Figure 7 – Home Screen Display Room Setting Time of day Temperature Temperature Battery Level Indicator Indicating the current power Mo level of the 2 “AA” batteries. Set P Full power remaining. Half power remaining. Change The batteries Run should be replaced at this time with 2 new premium brand “AA” Alkaline batteries. SYSTEM FAN (See page 2 for more details) Heat Auto Menu System Fan Indicator Indica
ページ6に含まれる内容の要旨
INSTALLER/CONFIGURATION MENU To enter the Configuration Menu, SYSTEM must be set to HEAT, COOL, Em or AUTO. Press the Menu button for at least 5 seconds. The display will show item #1 in the table below. Press Menu button to advance to the next menu item. Press or to change an item option. INSTALLER/CONFIGURATION MENU MENU MS2/ HP1/ DISPLAYED Press or to SCREEN COMMENTS SS1 HP2 (FACTORY DEFAULT) select from listed options NUMBER 01 (OFF) Lk L Selects Keypad Lockout. (Not ava
ページ7に含まれる内容の要旨
INSTALLER/CONFIGURATION MENU 1 & 2)Keypad Lockout – This menu selection will display 6) Energy Management Recovery: Energy Management “Lk” and “OFF” (default, keypad not locked out). The Recovery (E) On enables the thermostat to start heating and are used to toggle the selection between or cooling early to make the building temperature reach OFF and “L” (keypad locked out). When the keypad the program setpoint at the time you specify. Heating lockout selection is enabled “L”, and the MENU
ページ8に含まれる内容の要旨
INSTALLER/CONFIGURATION MENU per week can be changed to P3 by pressing the or thermostat. (Refer to Comfort Alert Yellow Alert Codes in Troubleshooting section.) If a Comfort Alert module is keys. A selection of 0 Days for non-programmable not connected, or to disable active protection, turn this will eliminate the need for EMR, and that step in the feature OFF. If a Comfort Alert module is connected and menu will be skipped. this feature is turned OFF, the thermostat will still receive
ページ9に含まれる内容の要旨
PROGRAMMING Set Current Time and Date 4) Press or button to change the temperature to your selected temperature for the 1st heating period. 1) Press Menu and then Time button once. The display will show the hour only. 5) Press TIME button, time will flash. 2) Press and hold either the or button until you 6) Press or button to adjust the start time for the reach the correct hour and AM/PM designation (AM 1st period. begins at midnight, PM begins at noon). 7) The time will change in 1
ページ10に含まれる内容の要旨
PROGRAMMING Worksheet for Re-Programming 7 Day and 5+1+1 Day Program Heating Wake Up Leave For Work Return Home Go To Bed Program (Period 1) (Period 2) (Period 3) (Period 4) 6:00 AM 70°F 8:00 AM 62°F 5:00 PM 70°F 10:00 PM 62°F MON TUE WED THU FRI 6:00 AM 70°F 8:00 AM 62°F 5:00 PM 70°F 10:00 PM 62°F SAT 6:00 AM 70°F 8:00 AM 62°F 5:00 PM 70°F 10:00 PM 62°F SUN Cooling Wake Up Leave For Work Return Home Go To Bed Program (Period 1) (Period 2) (Period 3) (Period 4) 6:00 AM 75°F 8:00 AM 83°F 5:00
ページ11に含まれる内容の要旨
TROUBLESHOOTING Reset Operation function correctly contact your heating/cooling service person Note: When thermostat is reset, installer configuration menu or place of purchase. settings and programming will reset to factory settings. Note: Be sure to review the installer configuration menu If a voltage spike or static discharge blanks out the display settings. or causes erratic thermostat operation, you can reset the thermostat by removing the wires from terminals R and C To reset the p
ページ12に含まれる内容の要旨
HOMEOWNER HELP LINE: 1-800-284-2925 White-Rodgers is a division of Emerson Electric Co. The Emerson logo is a trademark and service mark www.white-rodgers.com of Emerson Electric Co. www. emersonclimate.com
