ページ1に含まれる内容の要旨
Model: 1F89EZ-0251
Emerson Blue Easy Set
Heat Pump
2H/1C
Non-Programmable Thermostat with 3 Temperature Pre-Sets
Home, Sleep and Away
Installation Instructions and User Guide
Message to Homeowner
Congratulations on choosing the Emerson Blue Easy Set
Thermostat. The Easy Set is designed to be the easiest
thermostat you have ever used. This thermostat features
Home, Sleep, and Away temperature pre-sets. Just press
the button and go. Included with the easy set is the same
tempe
ページ2に含まれる内容の要旨
1 Get to know your thermostat Figure 1. Thermostat buttons and switches Before you begin using your thermostat, you should be familiar with its features and with the display and the location and operation of the thermostat buttons and switches. Set at Home 2 The Thermostat Buttons and Switches 1 Raises temperature setting. 2 Lowers temperature setting. 3 Easy Temperature pre-sets (Home, Sleep, Away). 4 SYSTEM switch (COOL, OFF, HEAT, EMER). FAN switch (ON, AUTO). 5 4 5 3 The Display 6 In
ページ3に含まれる内容の要旨
Using your thermostat Change Home, Sleep and Away Home, Sleep and Away Temperature Temperature Pre-sets Pre-Sets 1. Move SYSTEM switch to HEAT position. You can set your (Home, Sleep, Away) temperatures for use when you get home, go to sleep, or leave home. Then, just 2. Using the or button, set the desired temperature. press the button you want and go. 3. Press and hold the Home, Sleep, or Away button for 3 Favorite Temperatures are set at the factory as indicated in seconds. The disp
ページ4に含まれる内容の要旨
Installation Battery Remove the Old Thermostat Door 1. Turn off power to the heating and cooling system. 2. Remove the front cover of the old thermostat, this usually pulls off. 3. Loosen the screws that hold the thermostat to the wall. 4. Identify each wire attached to the old thermostat. Mounting Hole 5. Disconnect the wires from old thermostat one at a time. DO Mounting NOT LET WIRES FALL BACK INTO THE WALL. Hole Install the New Thermostat 1. Open the battery door and detach the new thermo
ページ5に含まれる内容の要旨
Installation Select Configuration Options The configuration menu allows you to set certain thermostat operating characteristics to your system or personal requirements. Enter Menu Menu Navigation SYSTEM Set at Press Home and hold Press for next. Press to go back for 3 seconds Configuration Menu Menu Screen Displayed Press or Number (Factory Default) to select options 01 Sleep On Select Sleep Timer On or OFF (OFF) If selected OFF, skip to menu screen 04 02 h 1 to
ページ6に含まれる内容の要旨
Troubleshooting Reset Operation If a voltage spike or static discharge blanks out the display or for approximately 10 seconds until the display goes blank. If causes erratic thermostat operation, you may need to reset the thermostat has power, has been reset and still does not the thermostat. To reset, the System Switch must be in Cool, function correctly contact your heating/cooling service person HEAT, or EMER. Simultaneously hold the and buttons or place of purchase. Symptom Possible C
ページ7に含まれる内容の要旨
THERMOSTAT ** O/B Y G W2 C L R SYSTEM SYSTEM Changeover MONITOR Fan Relay* SWITCH Aux/Emergency Compressor Relay Heat Relay Contactor (Stage 2) Hot 24 VAC 120 VAC Neutral Changeover Relay is energized in COOL when O/B switch is in the “O” position * Changeover Relay is energized in HEAT when O/B switch is in the “B” position TRANSFORMER Technical Data (Class II Current Limited) The 24 volt neutral connection to terminal C on the thermostat is not required if you ** replace the batteries once a
ページ8に含まれる内容の要旨
Homeowner Help Line: 1-800-284-2925 White-Rodgers is a division of Emerson Electric Co. The Emerson logo is a www.white-rodgers.com trademark and service mark of Emerson Electric Co. www.emersonclimate.com
