ページ1に含まれる内容の要旨
Quick Reference/Installation Guide
CONTENTS
1 FEATURES
2
SPECIFICATIONS
3 INSTALLATION
3.1
Replacing Existing Thermostat
3.2
Installing Your New Thermostat
Premier Series
4 TESTING YOUR NEW THERMOSTAT
MODEL
5
7-Day Programmable PROGRAMMING
5.1
Default Thermostat Settings
2-Heat/2-Cool&Heat Pump
5.2
Setting Current Time of Day and Day of Week
5.3
Digital Thermostat Setting Temperature Differential and Residual
5200
Cooling Fan Feature
5.3.1
Setting First Stage Differential
5.3.2
Setting Second St
ページ2に含まれる内容の要旨
FEATURES INSTALLATION cont. 1 3 • Contemporary styling with large display 3.1 Replacing Existing Thermostat cont. • 7 Day Programming Flexibility •AC Powered with Battery Back-up (2AAAlkaline batteries included) 4.After labeling and removing all wires from terminals,unscrew the existing thermostat • Relay Outputs for Maximum Compatibility mounting base from wall. Make sure to secure wires to prevent them from slipping • EasyAccess Front Battery Door back into the hole in the wall. • Pre-programm
ページ3に含まれる内容の要旨
TESTING YOUR INSTALLATION cont. 3 NEW THERMOSTAT cont. 4 3.2 Installing Your New Thermostat cont. 1. Place the system switch in theHEAT position. 2. Press the button on the keypad until the setpoint temperature setting is a minimum of 3 degrees 7. Mark placement of mounting holes as appropriate and drill using a 3/16" drill bit. higher than the current room temperature. The heating system should start within several 8. Gently tap supplied plastic anchors into the holes in the wall. seconds.The f
ページ4に含まれる内容の要旨
PROGRAMMING cont. PROGRAMMING cont. 5 5 5.2 Setting Current Time of Day and Day of Week cont. 5.3 Setting Temperature Differential and Residual Cooling Fan Feature cont.. 2. Press the or buttons to set the current hour. 5.3.2 Setting Second Stage Differential cont.. 3. PressDAY/TIME button again,the minute portion of the time will flash. 4. Press the or buttons to set the current minute. 3. PressRESUME button again and the LCD display will show "d2x˚",where "x" equals the ˚F / ˚C differential se
ページ5に含まれる内容の要旨
PROGRAMMING cont.. PROGRAMMING cont.. 5 5 5.4 Setting Your Energy Saving Programs cont.yt 5.4 SettingYourEnergySavingPrograms Tips Before Starting 5.4.1 5.4.2 Using Quick Program Groups or Individual Day Programming cont.. • It is important for you to set the current time of day (noteAM/PM indicator in display),and the current day of IndividualDays– week correctly to avoid problems with program execution. This must be done prior to entering any program allowsyoutoprogrameachdayoftheweekindividua
ページ6に含まれる内容の要旨
ADDITIONAL PROGRAMMING cont.. cont.. OPERATION FEATURES 5 6 6.2 Temporary Program Override 5.4 Setting YourEnergySavingPrograms cont. 1. Pressandhold or buttonsfor3seconds. The 5.4.3 EnteringYour Program cont.. entiredisplaywillflashonceandtheSETTEMP indicatorwillbeflashing. Releasethe or 3. If you desire to use a different Quick Program Group or Individual Day program mode you can buttonsandpressthe or buttonsagainas change by pressing theDAY/TIME button to select another group in the following
ページ7に含まれる内容の要旨
ADDITIONAL ADDITIONAL OPERATION FEATURES cont.. OPERATION FEATURES cont. 6 6 6.5 Compressor Protection cont. 6.8 Low Battery Detection and Replacement cont. NOTE: The installer can reset the thermostat and bypass the compressor protection When this feature determines that the back-up batteries status is low,low battery indicator features by pressing theRESET button. This will erase all entered programs,current will appear in the display. The thermostat will continue to function normally ifAC pow
ページ8に含まれる内容の要旨
TROUBLESHOOTING TROUBLESHOOTING cont. 7 7 SYMPTOM POTENTIALSOLUTION SYMPTOM POTENTIALSOLUTION Check to see ifOFF is shown in display. This indicates that the Thermostat does not Thermostat turns on Increase or decrease second (auxiliary) stage temperature system is turned off at the thermostat. Move the system turn on heating or differential setting as appropriate to provide the desired second (auxiliary) selector switch to theHEAT orCOOL position. After the cooling system. performance level. Se
ページ9に含まれる内容の要旨
TROUBLESHOOTING cont. WIRING DIAGRAMS 7 8 TypicalCarrier,Bryant,Payne,Day & Night and Reliant Heat Pumps THERMOSTATTERMINALBLOCK SYMPTOM POTENTIALSOLUTION R Y1 Y2 W2 E G O B L C The temperature sensed by the thermostat is lower than the 40˚ LO is shown in the F (5˚ C) lower limit of the thermostats display range. The display thermostat display will return to normal after the sensed temperature rises within R where the room the 40˚ to 99˚ F (5˚ to 37˚ C) display range. If the temperature in tempe
ページ10に含まれる内容の要旨
WIRING DIAGRAMS cont. WIRING DIAGRAMS cont. 8 8 TypicalLennox Heat Pumps (also see other Lennox diagrams) TypicalLennoxHP22 Heat Pump THERMOSTATTERMINALBLOCK THERMOSTATTERMINALBLOCK R Y1 Y2 W2 E G O B L C R Y1 Y2 W2 E G O B L C R R-VR Y M W1 Y2 E Y G E O F L R C L X TypicalLennoxHP19,HP20 Heat Pumps TypicalTrane Heat Pumps THERMOSTATTERMINALBLOCK R Y1 Y2 W2 E G O B L C THERMOSTATTERMINALBLOCK R Y1 Y2 W2 E G O B L C V-VR R M Y Y W E X2 F G R O X F B TypicalLennoxHP21 Heat Pump THERMOSTATTERMINALB
ページ11に含まれる内容の要旨
WIRING DIAGRAMS cont. 8 TypicalYork E1 Series Heat Pumps THERMOSTATTERMINALBLOCK W2 E R Y1 Y2 G O B L C R User Supplied Y Jumper W Braeburn Systems LLC warrants each new Braeburn thermostat against any defects that are due to faulty material or G YEAR workmanship for a period of two years after the original date of LIMITED purchase by a professional service technician. This warranty O WARRANTY and our liability does not apply to batteries, nor does it include X damagetomerchandiseorthethermostat
