ページ1に含まれる内容の要旨
PLCHD6
6 - DISC CD CHANGER
INSTRUCTION MANUAL
ページ2に含まれる内容の要旨
IMPORTANT NOTICE This Compact Disc Changer/Player has been tested and found to comply with the limits for a class B digital device in accordance with the specifications in Subpart J of part 15 of FCC Rules. This equipment generates and uses radio frequency energy, and it must be installed and used properly in accordance with the manufacturer's instructions. CAUTION This product is designed for 12 Volt DC Negative ground systems only. Your vehicle is compatible with this equipment if the negative
ページ3に含まれる内容の要旨
INTRODUCTION RESET FUNCTION A RESET button is located on the front panel (to the left side of EJECT button) and is accessible only when the magazine door is opened. The RESET button is recessed in order to prevent accidental engagement, and can be activated with the tip of ball- point pen or any similar pointed object. The reset circuitry is provided in order to protect the unit's microprocessor and tracking system and should be activated only under the following conditions: a. Initial installa
ページ4に含まれる内容の要旨
LOCATION OF CONTROLS 1. Compact Disc Magazine Slot 2. Reset Button 3. Eject Button (Press this button to eject the Magazine) 4. Slide Door 1 2 3 4 WIRING CONNECTIONS CD CHANGER CAR RADIO 3
ページ5に含まれる内容の要旨
HOW TO USE THE COMPACT DISC MAGAZINE Inserting Discs Inserting Discs into the supplied magazine. Up to 6 Discs may be inserted into the magazine. The Disc are numbered from 1 (bottom tray) to 6 (top tray). Note: Do not touch the recorded side of a Disc while inserting or removing it. Removing Discs 1.Press the Eject button to remove the Magazine. 2.Push the Release keys to remove the Discs. Precautions • Do not leave the magazine exposed to high temperature or direct sunlight. • Do not attempt
ページ6に含まれる内容の要旨
INSTALLATION • Use the supplied parts and mount the unit securely. The use of parts other than these supplied (specified) may loosen or damage internal components. • If installation presents any difficulties, consult your dealer for advice. • Before drilling a hole into the wall or floor the vehicle trunk, check that nothing is behind the panel. Never drill a hole in the fuel tank or any other important that may be attached to the trunk. • Take off the negative terminal connector (–) of the car
ページ7に含まれる内容の要旨
ACCESSORIES x2 x2 x4 a) Bracket b) Floor base plate c) Hex bolt (M5x12) with Washers x4 x4 x4 x1 d) Wing nut (06) e) Self tape screw (5x15) f) Self tape screw (3x15) g) Mount angle adjust key Important Angle set and locking screws • Be sure to adjust the mounting angle set screw (F) using the mounting angle adjust key to appropriate angle: Of for horizontal. 45° angle. or 90° for vertical mount
ページ8に含まれる内容の要旨
INSTALLATION DIAGRAMS HORIZONTAL / VERTICAL INSTALLATION PROCEDURES 1. Attach the brackets (a) to each side of the unit. Using the hex bolts with washers (c). 2.Determine the mounting location and drill 4 mounting holes approximately 3.5mm in diameter . 3.Secure the unit in place using 4 self-tapping screws (e). e) e) c) c) e) e) a) a) ø3.5mm ø3.5mm a) a) c) c) HORIZONTAL INSTALLATION c) e) a) d) b) a) c) b) Attach the brackets (a) to each side of the unit using hex bolts with washers (c). Lif
ページ9に含まれる内容の要旨
VERTICAL INSTALLATION c) e) a) b) d) a) b) c) Attach the brackets (a) to each side of the unit using hex bolts with washers (c). Lift the carpet and determine the mounting Attach the floor base plate (b) to the brackets a) location. Fix the floor base plate (b) to the floor using the wing nuts (d) using self-tape screw (f). d) d) d) d) Press the unit to the floor, and Lay down the carpet. Cut 1 “X” on Mount the unit in place, using 4 remove the wing nuts (d), and lift each area of the carpet w
ページ10に含まれる内容の要旨
SPECIFICATIONS General System Compact Disc audio system Usable Discs Compact Disc Operation voltage 10 - 15V Power consumption 6W or less (DC 14.4V) Operating electric current 400mA 14.4Volt Max. peak electric current 1.2A 14.4Volt Dimensions 284(W) x 186.5(O) x 74(H) mm Operational temperature range 5°F - 158°F Temperature range of storage -22°F - 176°F Test condition Ordinary room condition of temperature 68°±5.4°F and relative humidity 65% (DC 14.4±0.2V) Audio Frequency range 20Hz - 20KHz (
ページ11に含まれる内容の要旨
OPERATION Liquid Crystal Display (LCD) - (1) LCD display will only be active when the changer power is on. This display indicates all operation key's, including DISC number. Track number, and DISC icon. Random Play Button - (2) (Track or DISC Random) This is used for random selection Disc play, and sequence. Once this button is pressed. "RDM" is displayed in the Upper left corner of LCD commander, and disc selection will begin random play. When this button is pressed for more than 2 seconds, "DI
ページ12に含まれる内容の要旨
ERROR DISPLAY • Error 1: There's no Magazine, and DISC is clamping. • Error 2: It is impossible to discharge Magazine while ejecting. • Error 3: Loading is not completed after a certain time (8 sec) passed. • Error 4: Unloading is not completed after a certain time (8 sec) passed. • Error 5: Elevator does not reach to the target position after a certain time (8 sec) passed. Hole separated. • Error 6: Pickup is not moved to the center area even after a certain time (8 sec) passed in movement of
