ページ1に含まれる内容の要旨
Instruction Manual
HAS60E-IM-HW
04/2008
Instruction Manual
Chemiluminescence Detector
CLD Analyzer Module (combined with NGA 2000 Platform,
MLT, CAT 200 or TFID Analyzer)
nd
2 Edition 04/2008
www.EmersonProcess.com
ページ2に含まれる内容の要旨
CLD Chemiluminescence Detector Instruction Manual HAS60E-IM-HW 04/2008 ESSENTIAL INSTRUCTIONS READ THIS PAGE BEFORE PROCEEDING! Emerson Process Management (Rosemount Analytical) designs, manufactures and tests its products to meet many national and international standards. Because these instruments are sophisticated technical products, you MUST properly install, use, and maintain them to ensure they continue to operate within their normal specifications. The following instructions MUST be adhere
ページ3に含まれる内容の要旨
Instruction Manual HAS60E-IM-HW June 2007 NGA 2000 CLD Table of Contents PREFACE ...........................................................................................................................P - 1 DEFINITIONS .....................................................................................................................P - 1 SAFETY INSTRUCTIONS WIRING AND INSTALLATION OF THIS APPARATUS.......P - 2 OPERATING AND MAINTAINING THIS APPARATUS ...................................
ページ4に含まれる内容の要旨
Instruction Manual HAS60E-IM-HW June 2007 NGA 2000 CLD SECTION 2 INSTALLATION .............................................................................................. 2 - 1 2-1 UNPACKING ............................................................................................................... 2 - 1 2-2 ASSEMBLY................................................................................................................. 2 - 1 2-3 LOCATION............................................
ページ5に含まれる内容の要旨
Instruction Manual HAS60E-IM-HW June 2007 NGA 2000 CLD c. Relay Outputs Setup ............................................................................................ 3 - 12 Output number: ..................................................................................................................3 - 12 Invert signal: .......................................................................................................................3 - 12 Choose source module... .....................
ページ6に含まれる内容の要旨
Instruction Manual HAS60E-IM-HW June 2007 NGA 2000 CLD SECTION 6 REPLACEMENT PARTS ............................................................................... 6 - 1 6-1 MATRIX ...................................................................................................................... 6 - 1 6-2 REPLACEMENT PARTS ............................................................................................ 6 - 2 SECTION 7 RETURN OF MATERIAL ...........................................
ページ7に含まれる内容の要旨
Instruction Manual HAS60E-IM-HW June 2007 NGA 2000 CLD PREFACE The purpose of this manual is to provide information concerning the components, functions, installation and maintenance of the NGA 2000 CLD and the System Accessories of the NGA 2000 System. Some sections may describe equipment not used in your configuration. The user should become thoroughly familiar with the operation of this module before operating it. Read this instruction manual completely. DEFINITIONS The following definitions
ページ8に含まれる内容の要旨
Instruction Manual HAS60E-IM-HW June 2007 NGA 2000 CLD IMPORTANT SAFETY INSTRUCTIONS WIRING AND INSTALLATION OF THIS APPARATUS The following safety instructions apply specifically to all EU member states. They should be strictly adhered to in order to assure compliance with the Low Voltage Directive. Non-EU states should also comply with the following unless superseded by local or National Standards. 1. Adequate earth connections should be made to all earthing points, internal and external,
ページ9に含まれる内容の要旨
Instruction Manual HAS60E-IM-HW June 2007 NGA 2000 CLD OPERATING AND MAINTAINING THIS APPARATUS This instrument has left the factory in compliance with all applicable safety regulations. To maintain this operating condition, the user must strictly follow the instructions and consider the warnings in this manual or provided on the instrument. Before switching on the instrument, verify that the electrical supply voltage matches the instrument´s opera- ting voltage as set in the factory. Any interr
ページ10に含まれる内容の要旨
Instruction Manual HAS60E-IM-HW June 2007 NGA 2000 CLD SAFETY SUMMARY If this equipment is used in a manner not specified in these instructions, protective systems may be impaired. AUTHORIZED PERSONNEL To avoid loss of life, personal injury and damage to this equipment and on-site property, do not operate or service this instrument before reading and understanding this instruction manual and receiving appropriate training. Save these instructions. WARNING ELECTRICAL SHOCK HAZARD ! Do not operate
ページ11に含まれる内容の要旨
Instruction Manual HAS60E-IM-HW June 2007 NGA 2000 CLD WARNING OVERBALANCE HAZARD This analyzer module may tip instrument over if it is pulled out too far and the Platform is not properly supported. CAUTION Tampering with or unauthorized substitution of components may adversely affect the safety of this instrument. Use only factory documented/approved components for repair. Because of the danger of introducing additional hazards, do not perform any unauthorized modifi- cation to this instrument
ページ12に含まれる内容の要旨
Instruction Manual HAS60E-IM-HW June 2007 NGA 2000 CLD WARNING Before opening gas paths they must be purged with ambient air or neutral gas (N ) to avoid hazards caused by toxic, flammable, explosive 2 or harmful to health sample gas components! WARNING INTERNAL UV SOURCE ! Ultraviolet light from the ozone generator can cause permanent eye damage ! Do not look directly at the ultraviolet source ! Use of ultraviolet filtering glases is recommended. WARNING TOXIC CHEMICAL HAZARD! The optional UV l
ページ13に含まれる内容の要旨
Instruction Manual HAS60E-IM-HW June 2007 NGA 2000 CLD GASES AND GAS CONDITIONING (SAMPLE HANDLING) WARNING Take care of the safety instructions applicable for the gases (sample gases, test gases and ozonator air)! CAUTION PRESSURIZED GAS This module requires periodic use of pressurized gas. See General Precautions for Handling and Storing High Pressure Gas Cylindes, page P-6. CAUTION EXTERNALLY RESTRICT SAMPLE FLOW TO LESS THAN 2,200 cc/min. No restrictor is provided in the inlet of this module
ページ14に含まれる内容の要旨
Instruction Manual HAS60E-IM-HW June 2007 NGA 2000 CLD ELECTROSTATIC DISCHARGE CAUTION The electronic parts of the Analyzer Module can be irreparably damaged if exposed to electrostatic discharge (ESD). The instrument is ESD protected when the covers have been secured and safety precautions observed. When the housing is open, the internal components are not ESD protected anymore. Although the electronic parts are reasonable safe to handle, you should be aware of the following consid- erations: B
ページ15に含まれる内容の要旨
Instruction Manual HAS60E-IM-HW June 2007 NGA 2000 CLD GENERAL PRECAUTIONS FOR HANDLING AND STORING HIGH PRESSURE GAS CYLINDERS Edited from selected paragraphs of the Compressed Gas Association´s „Handbook of Compressed Gases“ published in 1981. Compressed Gas Association 1235 Jefferson Davis Highway Arlington, Virginia 22202 Used by Permission 1. Never drop cylinders or permit them to strike each other violently. 2. Cylinders may be stored in the open, but in such cases, should be protected aga
ページ16に含まれる内容の要旨
Instruction Manual HAS60E-IM-HW June 2007 NGA 2000 CLD DOCUMENTATION The following CLD instruction materials are available. Contact Customer Service Center or the local represen- tative to order. HAS60E-IM-HW Instruction Manual NGA 2000 CLD (this document) HAS60E-IM-SW39 Software Manual NGA 2000 CLD 90002496 Instruction Manual NGA 2000 Platform COMPLIANCES This product may carry approvals from several certifying agencies, including the Canadian Standards Association (which is also an OSHA accre
ページ17に含まれる内容の要旨
Instruction Manual HAS60E-IM-HW June 2007 NGA 2000 CLD GLOSSARY OF TERMS Analyzer Module The module that contains all sensor/detector components for development of a Primary Variable signal; includes all signal conditioning and temperature control circuitry. Backplane The interconnect circuit board which the Controller Board, Power Supply, Analyzer Module power and network cables, I/O Modules and Expansion Modules plug into. Control Module The Operator Interface plus the Controller Board. Contro
ページ18に含まれる内容の要旨
Instruction Manual HAS60E-IM-HW June 2007 NGA 2000 CLD Primary Variable The measured species concentration value from an Analyzer Module. Secondary Variable Data placed on the network by a module regarding current status, e.g., sample flow, temperature and pres- sure. Softkeys The five function softkeys located below the front panel display; they assume the function displayed directly above each on the display, a function dictated by software. System Any collection of Analyzer Module(s), Platfor
ページ19に含まれる内容の要旨
Instruction Manual HAS60E-IM-HW June 2007 NGA 2000 CLD ANALYZER SYSTEM ARCHITECTURE The NGA 2000 CLD is available as a "stand-alone ana- The platform/MLT´s front panel can act as operator in- lyzer" or as a "blind" Analyzer Module (AM). The CLD terface for a stand-alone analyzer or as the a central analyzer module can be part of the stand-alone analyzer interface for multiple Analyzer Modules. In multi anal- or a component of an analyzers system (Fig. A-1). yzer systems, this feature eliminat
ページ20に含まれる内容の要旨
Instruction Manual HAS60E-IM-HW June 2007 NGA 2000 CLD The modular configurable bi-directional network offers ❏ Simple interconnection of analyzer modules to an the following options: analyzer system based on one of the three struc- tures - see below. ❏ Stand-alone analyzers (Single devices) These structures can be distinguished by acting of the host • analyzer modules in a platform including optional inputs and outputs (SIO/DIO). • with platform as host including system inputs and outputs (SI
