ページ1に含まれる内容の要旨
INSTALLATION MANUAL
SP-6CD
6 - DISC CD CHANGER SYSTEM
MODELSP-6CD
ページ2に含まれる内容の要旨
PACKING LIST MAIN UNIT Changer INSTALLATION PARTS Bracket (L) Bracket (R) Self-TappingScrew (M5 x 12) 1 pc. 1 pc. 4 pcs. HexagonalBolt 5 Meter DIN cable Seals with Washer (8 pin) M5x8 4 pcs. 1 pc. 1 pc. OTHER ACCESSORY CDMagazine Index seal sheet Installation Owner's Manual guide 1 pc. 1 pc. 1 pc. 1 pc. 1
ページ3に含まれる内容の要旨
BEFOREINSTALLINGTHEUNIT Transport lock screws ThemechanismintheCDchangeris"locked"intoplaceduringshipmentbythe transportscrews. Besuretoremovethescrewspriortoinstallation. l Caution l Afterremovingthetransportlockscrews,placethesuppliedsealsoverthescrew holes. Thesesealsareusedtokeepdustoutoftheunit,whichcouldcauseamalfunction. InstallationandWiringPrecautions Topreventashort-circuit, 1 l Besuretoturnofftheignitionandremovethenegative(-)batterycable,priortoinstallation. l Connectpowerwireslast.
ページ4に含まれる内容の要旨
SETTING THEANTI-VIBRATION SPRINGS This unit can be installed horizontally (suspended), vertically, and at a 45° angle. Once the installation position has been decided, it's necessarytosetthepositionofthebuilt-inanti-vibrationspringsinsidetheunit. Pleasedothisbeforeperformingtheprocedure. Vibration may cause the disc to skip if the unit is used before properly setting the anti-vibration springs. l At the time of shipping, the built-in anti-vibration springs is set for horizontal installation "H".
ページ5に含まれる内容の要旨
PROCEDURE FORVERTICALINSTALLATION 1 l Confirmthatthebuilt-inanti-vibrationspringsonboththeleftandright sides are set to the vertical installation position "V". l Attachbracket(L)andbracket(R)usingthehexagonalbolts(M5x8). Determine the mounting location and drill four mounting holes. 2 Never mount the unit near the fuel tank. Drill holes 4mm in diameter. Secure the unit in place, using four self-tapping screws (M5 x 12). 3 Self-tapping screw (M5 x 12) PROCEDUREFOR45°ANGLE INSTALLATION 1 l Confirm
ページ6に含まれる内容の要旨
PROCEDUREFORMOUNTINGUNDERREARDECK 1 l Confirmthatthebuilt-inanti-vibrationspringsonboththeleftandright sides are set to the horizontal installation position "H". l Attachbracket(L)andbracket(R)usingthehexagonalbolts(M5x8). 2 Determine the mounting location and drill four mounting Attach the CD changer using four self-tapping screws 3 holes. (M5 x 12). 4mm 5
ページ7に含まれる内容の要旨
DIN cable (8-pin) VEHICLEWIRING Mating 8-pin DIN socket on rear of compatible radio chassis (see Note 1 below). Car Stereo with CD Changer Controls CD changer NOTE: 1. Check with your Audiovox car audio dealer to be sure your stereo is directly compatible with this CD changer. 2. Wiring instructions for use with FM Modulator/Commander Systems are included with the CDC-MC1, CDC-MCR2, P-MC3 and P-MCR4 accessories. 6