ページ1に含まれる内容の要旨
Z500
Z100 / Z300 Z700
OWNER’S MANUAL
PLEASE CAREFULLY READ THIS ENTIRE MANUAL BEFORE
OPERATING YOUR NEW ELLIPTICAL!
ページ2に含まれる内容の要旨
Table of Contents Product Registration ..2 Important Safety Instructions 3 Important Electrical Information 4 Important Operation Instructions ..4 Assembly Instructions .5 Operation of Your New Elliptical ...11 Manufacturer s Limited Warranty ..15 ATTENTION-THISELLIPTICAL IS INTENDED FOR RESIDENTIAL USE ONLY AND IS WARRANTED FOR THAT APPLICATION. ANY OTHER APPLICATION VOIDS THIS WARRANTY IN ITS ENTIRETY. 1
ページ3に含まれる内容の要旨
CONGRATULATIONS ON YOUR NEW ELLIPTICAL AND WELCOME TO THE SPIRIT FAMILY! Thank you for your purchase of this quality elliptical trainer from Spirit Manufacturing, Inc. Your new elliptical was manufactured by one of the leading fitness manufacturers in the world and is backed by one of the most comprehensive warranties available. Through your dealer, Spirit will do all we can to make your ownership experience as pleasant as possible for many years to come. The local dealership where you purchased
ページ4に含まれる内容の要旨
Important Safety Instructions WARNING - Read all instructions before using this appliance. Do not operate elliptical on deeply padded, plush or shag carpet. Damage to both carpet andelliptical may result. Keep children away from the elliptical. There are obvious pinch points and other caution areas that can cause harm. Keep hands away from all moving parts. Never operate the elliptical if it has a damaged cord or plug. If the elliptical is not working properly, call your dealer. Keep the c
ページ5に含まれる内容の要旨
Important Electrical Information WARNING! NEVER remove any cover without first disconnecting AC power supply. If A.C. voltage varies by ten percent (10%) or more, the performance of your elliptical may be affected. Such conditions are not covered under your warranty. If you suspect the voltage is low, contact your local power company or a licensed electrician for proper testing. NEVER expose this elliptical to rain or moisture. This product is NOT designed for Use outdoors, near a pool or spa
ページ6に含まれる内容の要旨
Assembly Instructions UNPACKING THE UNIT 1. Using a razor knife (Box Cutter) cut the outside, bottom, edge of box along the dotted Line. Lift Box over the unit and unpack. 2. Carefully remove all parts from carton and inspect for any damage or missing parts. If damaged parts are found, or parts are missing, contact your dealer immediately. 3. Locate the hardware package. The hardware is separated into steps. Remove the tools first. Remove the hardware for each step as needed to avoid confusion.
ページ7に含まれる内容の要旨
STEP 3: CONNECTING ARM ASSEMBLY 1. Align the hole in the end of the Connecting arms (L&R)(pivoting rod end) with the hole in the bracket of the Lower Handle Bars (L&R). The rod end should be on the inside of the Lower Handle Bars (L&R) bracket. Take 2pcs of 5/16" x 1-1/4" Hex Head Screws and install it through the Lower Handle Bars (L&R) bracket and the rod end. Install 2pcs of 5/16" x 20 x 1.5T Flat Washers, 2pcs of 5/16" x 7T Nyloc Nuts tighten firmly using the 12m/m Wrench on the 5/16" x 7T N
ページ8に含まれる内容の要旨
Assembly drawing step 1 7 XE Series Elliptical
ページ9に含まれる内容の要旨
step 2 8 XE Series Elliptical
ページ10に含まれる内容の要旨
step 3 9 XE Series Elliptical
ページ11に含まれる内容の要旨
step 4 10 XE Series Elliptical
ページ12に含まれる内容の要旨
Transportation The elliptical is equipped with two transport wheels which are engaged when rear of XE Series Elliptical is lifted. Operation of Your Elliptical Getting familiar with the control panel Starting a program Quick Start After the console powers up you may press the Start key to begin, this will initiate the Quick Start mode. In Quick Start the Time will count up from zero and the workload may be adjusted manually by pressing the Up/Down buttons. Distance and Calories will accrue, star
ページ13に含まれる内容の要旨
Manual Using the Up/Down keys, highlight the Manual icon at the top of the display and press Enter key. The profile will be blinking and you may use the Up/Down keys to adjust the program work level and then press Enter. The Time window will now be blinking. Use the Up/Down keys to adjust the program Time and then press Enter. The Distance window will now be blinking and you can adjust a target Distance using the Up/Down keys then press Enter. Calories will now be blinking, repeat the same proce
ページ14に含まれる内容の要旨
User Program This mode allows you to build and save your own custom program. Press the Up or Down key until the User icon at the top of the display is blinking then press Enter. The first column of the profile will be blinking. Use the Up/Down keys to adjust the work level then press Enter. The second column will now be blinking. Repeat the same process as above and press Enter. Repeat this process until all the columns are adjusted to your liking. All the settings will be saved as a custom prog
ページ15に含まれる内容の要旨
FUNCTIONS TIME: Count up: accumulates training time from zero to 99:59. Count down: counts down from preset time to zero. SPEED/ RPM: Automatically toggles between SPEED and RPM every 6 seconds. Speed is in miles per hour (or kilometers per hour) DISTANCE: Count up: accumulates training distance from 0.00 to 99.99 miles. Count down: counts down from preset distance to zero. CALORIES: Accumulates calories burned from 0 to 9999. This is an estimated number only to be used from w
ページ16に含まれる内容の要旨
Manufacturer’s Limited Warranty Effective September 15, 2006 ELLIPTICAL WARRANTY Spirit Manufacturing Inc. warrants all its elliptical parts for a period of 2 years from the date of retail sale, as determined by sale receipt, or in the absence of a receipt eighteen (18) months from the original factory shipping date, Spirit s responsibilities include providing new or remanufactured parts, at Spirit s option, and technical support to our independent dealers and servicing organizations. In the ab
