ページ1に含まれる内容の要旨
D00785400A
»
CD-X1700
DUAL CD PLAYER
OWNER’S MANUAL / MANUAL DEL USUARIO
ページ2に含まれる内容の要旨
English IMPORTANT SAFETY PRECAUTIONS For U.S.A IMPORTANT (for U.K. Customers) TO THE USER DO NOT cut off the mains plug from this This equipment has been tested and found to equipment. comply with the limits for a Class A digital device, DO NOT cut off the mains plug from this pursuant to Part 15 of the FCC Rules. These limits equipment. are designed to provide reasonable protection If the plug fitted is not suitable for the power points against harmful interference when the equipment in your ho
ページ3に含まれる内容の要旨
IMPORTANT SAFETY INSTRUCTIONS (1) English 1 Read these instructions. 13 Unplug this apparatus during lightning storms or when unused for long periods of time. 2 Keep these instructions. 14 Refer all servicing to qualified service personnel. 3 Heed all warnings. Servicing is required when the apparatus has been 4 Follow all instructions. damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects 5 Do not use this apparatus near water. have fallen into the
ページ4に含まれる内容の要旨
English IMPORTANT SAFETY INSTRUCTIONS (2) SAFETY INFORMATION This product has been designed and manufactured according to FDA regulations "title 21, CFR, chapter 1, subchapter J, based on the Radiation Control for Health and Safety Act of 1968", and is classified as a class 1 laser product. There is no hazardous invisible laser radiation during operation because invisible laser radiation emitted inside of this product is completely confined in the protective housings. The label required in this
ページ5に含まれる内容の要旨
Table of contents English 1. Before you start............................................... 6 Effect level setting....................................... 16 1.1 Environmental conditions .......................... 6 FLANGER................................................... 16 1.2 Beware of condensation............................. 6 ECHO .......................................................... 16 1.3 Handling of discs ....................................... 6 FILTER...........................
ページ6に含まれる内容の要旨
English 1. Before you start 1.1 Environmental conditions 1.3 Handling of discs The TASCAM CD-X1700 may be used in most The unit has been designed specifically for areas, but to maintain top performance, and reproduction of discs bearing the mark. No prolong operating life, observe the following other discs can be reproduced. environmental conditions: Observe the following: The nominal temperature should be between 5°C • Always place the compact discs in the trays with and 35°C (41°F and 95°F). t
ページ7に含まれる内容の要旨
2. Functions and Controls English 2-1. Main Unit (Front Panel) 1 POWER switch 3 Tray LEDs Turns the power on and off. The tray LEDs light Lights when power is supplied. when power is supplied. 4 OPEN keys When Timer start function is on, playback begins Open and close the appropriate tray. when power is supplied. NOTE 2 Disc trays … These keys cannot be used when direct Insert CD into these trays, label side upwards. mode (Preset menu: page 23) is off and disc is being played back. 2-2. Main Un
ページ8に含まれる内容の要旨
English 2. Functions and Controls 2-3. Remote Controller (Top Panel) REMAIN: REMAIN indicator in the LCD will 0 OPEN key light Opens and closes the appropriate tray. TOTAL REMAIN: The track number display area NOTE shows the number of tracks of … These keys cannot be used when direct inserted disc, however, for 5 seconds mode (Preset menu: page 23) is off and in the end of track, the current track a disc is being played back. number flashes and for 5 seconds in the beginning of the track, the cu
ページ9に含まれる内容の要旨
2. Functions and Controls English Pressing and holding the SHIFT key while • Key control pressing this key selects the parameter display • Preset menu mode. •Effect parameters TEMPO ∑ KEY ∑ TAP ∑ BPM (∑ DIR). • Sampler tempo/level • Program edit t SCRATCH key •Track memory number select Turns the scratch play mode on and off. When scratch play mode is on, this key lights and scratch d FX SYNC key can be performed by Jog wheel. (∑ page 15) Turns on and off synchronization of the effect time with
ページ10に含まれる内容の要旨
English 2. Functions and Controls x IN and OUT keys b TEMPO / BANK key Use these keys to record and clear the sampled Selects the tempo range, either +/-8, 16, 32, 100 or sound. When you have recorded the sample, these 0%. keys will light. Start and stop sample playback Selects the track memory bank from A to E. using these keys. (∑ page 17) (∑ page 18) Pressing and holding the IN key then using the Jog wheel controls the sampler output level. n BEND +/ A.RDY, –/A.CUE keys Use these keys to
ページ11に含まれる内容の要旨
2. Functions and Controls English 2-5. Remote Controller (LCD) . M indicator Q LOOP indicator If there is track memory data for the current Lights when loop play is engaged. selected track in the current selected memory bank, this indicator lights. W S indicator Lights when loop mode is set to single loop. / TRACK indicator E ALL indicator ! REMAIN indicator Lights when loop mode is set to all loop. When the time mode is set to remain time mode, this indicator lights. R Time Address Bar Shows
ページ12に含まれる内容の要旨
English 3. Playback operation When the CUE key has the stored point, the CUE 3-1. CUE key lights. The stored cue point cannot be erased but can be overwritten. The CD-X1700 can memorize the play start point as a cue point. If the cue point is memorized, NOTE pressing the CUE key locates the unit to the cue … When the unit is paused and the poin. indicator in the LCD lights, pressing the SET key then pressing the CUE 1-3 key starts the unit automatically. To memorize the CUE point There are tw
ページ13に含まれる内容の要旨
3. Playback operation English Re-looping 3-4. A-B Looping When loop play is disengaged and loop points are already stored, pressing the LOOP key starts re- To store the LOOP points loop playback and the LOOP key lights. NOTE … Loop points can be stored when loop points are not stored on the unit (A and Erasing the LOOP points B key don’t light). If loop points are already stored, erase these points first, Pressing the A and B key at the same time erases then store the loop points again. the loo
ページ14に含まれる内容の要旨
English 3. Playback operation Using the TEMPO slider 3-6. Pitch Bending The TEMPO slider controls playback tempo. Tempo changes are displayed in the LCD. When playing back a disc, pressing the BEND + or – key, or using the Jog wheel can change playback tempo momentary. Pressing the + key or moving the Jog wheel clockwise increases the playback speed and returns to original speed when release this key or stop the Jog wheel moving. Pressing the - key or moving the Jog wheel counterclockwise decr
ページ15に含まれる内容の要旨
4. More advanced operation English 4-1. Key control 4-3. Brake The CD-X1700 features up to +/-16% key control. Brake function simulates the braking audio just Key control range is determined with tempo range like turning off the analog turntable. Pressing the setting. BRAKE key turns the brake function on and off. When tempo and key control range is set to 8%, When brake function is activated, BRAKE key key value can be set in 0.1% steps. When tempo lights. and key control range is set to 16%
ページ16に含まれる内容の要旨
English 4. More advanced operation The effect level parameter is shown in the Effect time setting parameter display. When an effect is activated, using the Jog wheel can adjust the effect time. FLANGER Pressing the FLANGE key activates the Flanger effect. Effect time: 10msec – 16sec (default: 500msec) Effect beat: 32, 16, 8, 4, 2, 1, 1/2 (default: 1) Effect level: 0 – 100 (default: 75) The effect time parameter is shown in the parameter display. ECHO NOTE Pressing the ECHO key activates the Echo
ページ17に含まれる内容の要旨
4. More advanced operation English NOTE 4-5. Reverse play … If eight seconds elapse, or if the end of the track is reached without pressing the The CD-X1700 features the reverse play function. OUT key, the end point of the sample Pressing the REVERSE key changes playback will automatically be set at that point. direction. When playback is reversed, the REVERSE key will light. Using the A-B loop as a sample source When you have set up an A-B loop, you can press and hold the OUT key and press the
ページ18に含まれる内容の要旨
English 4. More advanced operation Sampler Loop 4-7. Track Memory / Recall Pressing and holding the SAMPLE key then pressing the OUT key turns the sampler loop play The CD-X1700 can memorize the various on and off. When sampler loop play is activated, playback settings of current selected track up to LOOP LED will light. 100 tracks of memory in each 5 banks (A to E). You could use each bank for a different player or use the other bank for a different setting for a track, for example. Sampler
ページ19に含まれる内容の要旨
4. More advanced operation English 1. Select the memory bank by pressing and holding Memory data the SHIFT key then pressing the … l DISC ID … CUE point TEMPO/BANK key. … CUE 1-3 points … LOOP A/B points … LOOP mode … Play mode … Tempo data … Tempo Range … Key Original On/Off … TAP value … Brake On/Off … Brake Time 2. Enter the recall mode by pressing and holding … Key value … Time mode the SHIFT key then pressing the … Sampling points … Effect setting FLASH/RECALL key. Using the Jog wheel to N
ページ20に含まれる内容の要旨
English 4. More advanced operation 4-8. Fader Start 4-11. Auto Ready Connect the FADER START jack on the rear panel Auto Ready function allows the unit to pause the of the main unit and fader start jack on the external beginning of the next track when playback of the device which supports the fader start function (i.e. current track is finished. X-9, X-17, X-15, XS-3, etc…) with Fader Start The behavior of Auto Ready function is follows. Cable which is supplied to perform the fader start/back cu
