ページ1に含まれる内容の要旨
Installation, Start-Up and Maintenance Manual
ICE SERIES CUBERS
ICE0250 through ICE2100 SERIES*
*Includes Undercounter and 22 Inch Series
ICE-O-Matic
11100 East 45th Ave
Denver, Colorado 80239
Part Number 9081264-01 Print Date 3/05
ページ2に含まれる内容の要旨
ICE Series Forward How To Use This Manual ICE-O-Matic provides this manual as an aid to the service technician in installation and maintenance of the ICE Series (electro-mechanical) cube ice machines. Do not attempt to perform installation, start-up or maintenance unless you have read and fully understand this manual. If at any time you encounter conditions that are not addressed in this manual, call, E-mail or write the ICE-O-Matic Service Department: ICE-O-Matic th 11
ページ3に含まれる内容の要旨
ICE Series Table of Contents Forward Page i Table of Contents Page ii Freight Claim Procedure Page iii Warranty Page iv Model Number and Serial Number Format Page 1 Installation Guidelines Page 2 Remote Condenser Guidelines Page 4 Electrical and Plumbing Requirements Page 6 How the Machine Works Page 12 Start-Up Procedure Page 13 General Maintena
ページ4に含まれる内容の要旨
ICE Series Freight Claim Procedure Freight Claims Important! Inspect Promptly This merchandise has been carefully inspected and packed in accordance with the carrier’s packing specifications. Responsibility for safe delivery has been assumed by the carrier, if loss or damage occurs, you as the consignee must file a claim with the carrier and hold container for carrier’s inspection. Visible Loss or Damage Any external evidence of loss or damage must be fully described and noted on
ページ5に含まれる内容の要旨
ICE Series Warranty ICE-O-MATIC Parts and Labor Domestic & International Warranty Mile High Equipment Company (the “Company”) warrants Ice-O-Matic brand ice machines, ice dispensers, remote condensers, and ice storage bins to the original user customer against defects in material and factory workmanship for a period of thirty-six(36) months on cube ice machines and twenty-four (24) months on flake ice machines, “compressed ice” ice machines, ice dispensers, remote condensers,
ページ6に含まれる内容の要旨
ICE Series Model and Serial Number Format Model and Serial Number Format The serial number format and machine specifics are detailed on the data plate. ICE 040 0 H A 2 Design Level Condenser Type: A=Air, W=Water, R=Remote Cube Size: H=Half, F=Full Voltage: 0=115V, 6=230V/60Hz. 5=240V/50Hz. Approximate Production in 24 hours @70 °FAir/50 °FWater
ページ7に含まれる内容の要旨
ICE Series Installation Guidelines Installation Guidelines For proper operation of the ICE-O-Matic ice machine, the following installation guidelines must be followed. Failure to do so may result in loss of production capacity, premature part failures, and may void all warranties. Reference the installation parameters prior to installing the machine: Ambient Operating Temperatures Minimum Operating Temperature: 50°F (10°C) Maximum Operating Temperature 100°F (38°C), 110°F (
ページ8に含まれる内容の要旨
ICE Series Installation Guidelines Secure the machine on top of the bin or dispenser. Attach the ice machine to the bin with the mounting straps provided with the bin or dispenser. If the ice machine is to be mounted on a bin or dispenser other than an ICE-O-Matic, refer to the manufactures instructions for machine mounting. If the ice machine is to be stacked on top of another ice machine, a stacking kit will need to be installed. Refer to the installation instructions included
ページ9に含まれる内容の要旨
ICE Series Remote Condenser Guidelines Remote Condenser Installation For proper operation of the ICE-O-Matic ice machine, the following installation guidelines must be followed. Failure to do so may result in loss of production capacity, premature part failure, and may void all warranties. Remote condensers must be installed per local building codes. A two to four inch diameter roof penetration will be needed for refrigerant lines and electrical conduit. The penetration should be
ページ10に含まれる内容の要旨
ICE Series Remote Condenser Guidelines The ICE0500R3, ICE0606R3, ICE806R3, ICE1006R3, ICE1606HR3 and ICE1506R2 Remote ice makers incorporate the mixing valve in the condenser. This configuration allows up to a 100 foot calculated remote line set run. Reference the diagram below to calculate the maximum 100 foot line set run. ICE Machine Model Number Remote Condenser Model Number ICE1606HR3 LRC2661 ICE1506HR2 LRC2661 ICE1006R3 VRC2061 ICE806R3 VRC2061 I
ページ11に含まれる内容の要旨
ICE Series Electrical and Plumbing Requirements Electrical and Plumbing Requirements: ICEU150, 220, 225 and 226 Note: The ICEU150, 220, 225 and 226 do not have a splash curtain. These models utilize a thermostatic bin control in place of a mechanical bin switch. Page 6
ページ12に含まれる内容の要旨
ICE Series Electrical and Plumbing Requirements Electrical and Plumbing Requirements: ICEU300 Note: The ICEU300 Series do not have a splash curtain. This models utilize a thermostatic bin control in place of a mechanical bin switch Page 7
ページ13に含まれる内容の要旨
ICE Series Electrical and Plumbing Requirements Electrical and Plumbing Requirements: ICE0250, ICE0400, ICE0500 ICE0600 Page 8
ページ14に含まれる内容の要旨
ICE Series Electrical and Plumbing Requirements Electrical and Plumbing Requirements: ICE0806 and ICE1006 Page 9
ページ15に含まれる内容の要旨
ICE Series Electrical and Plumbing Requirements Electrical and Plumbing Requirements: 48 Inch Wide Cubers Page 10
ページ16に含まれる内容の要旨
ICE Series Electrical and Plumbing Requirements Electrical and Plumbing Requirements: 22 Inch Wide Cubers Page 11
ページ17に含まれる内容の要旨
ICE Series Electrical and Plumbing Requirement Electrical and Plumbing Requirements : ICE1606 Remote Page 12
ページ18に含まれる内容の要旨
ICE Series Electrical and Plumbing Requirements Electrical and Plumbing Requirements : ICE1506 Remote Page 13
ページ19に含まれる内容の要旨
ICE Series How the ICE Machine Works How the ICE Machine Works A general description of how the ICE Series cubers work is given below. With the ICE/OFF/WASH switch in the ICE position, the compressor, water pump and condenser fan motor (when applicable) will energize starting the freeze cycle. During the freeze cycle, water is circulated over the evaporator(s) where the ice cubes are formed. When the suction pressure has pulled down to the proper cut-in pressure of the timer init
ページ20に含まれる内容の要旨
ICE Series Start-Up Procedure Start-Up Procedure Before starting the machine, make sure the machine is level within 1/8 inch in all directions, the bin or dispenser leg height can be adjusted by rotating the leg foot. Check the water level in the water trough. It should be approximately ½ inch above the top of the water pump impeller housing. The water level can be adjusted by bending the float arm. Move the ICE-OFF-WASH switch to the ICE position. Check for proper water fl
