ページ1に含まれる内容の要旨
RECORD THIS INFORMATION FOR FUTURE REFERENCE
BEFORE INSTALLING THE UNIT:
Model No. _______________ _____________________ Serial No.
Date Purchased __________ Place of Purchase ______________
MODEL RM2612 AND RM2812
Automatic/Manual Energy Selector
USA
SERVICE OFFICE
The Dometic Corp.
509 So. Poplar St.
REFRIGERATOR FOR LP/GAS
LaGrange, IN 46761
AND ELECTRIC OPERATION
CANADA
Dometic Dist.
866 Langs Dr.
Cambridge, Ontario
CANADA N3H 2N7
FOR YOUR SAFETY
WARNING
If you smell gas:
Improper installati
ページ2に含まれる内容の要旨
SECTION A. INSTALLATION The lower side vent is fitted with a panel which provides an 1.GENERAL INSTRUCTIONS adequate access opening for ready serviceability of the This appliance is designed for storage of foods and burner and control manifold of the refrigerator. This should be storage of frozen foods and making ice. centered on the back of the refrigerator. The refrigerators outlined herein have been design certified 3.CERTIFIED INSTALLATION by A.G.A. under ANSI Z21.19 Refrigerator Standard f
ページ3に含まれる内容の要旨
5.VENTILATION HEIGHTS 6. CLEARANCES Minimum clearances in inches to combustible materials are: Refer to FIG 1., Page 2 G: Top 0" K: Side 0" Installation with roof Minimum Ventilation vent and lower side vent heights in: L: Bottom 0" M: Rear 0" REFRIGERATOR INCHES MM N: See NOTE RM2612 54 1372 RM2812 60 1524 NOTE: Clearance "M" is between the rearmost part of the refrigerator and the wall behind the refrigerator. LOWER VENT CUTOUT NOTE: Clearance "N" is the distance between the bottom of the lowe
ページ4に含まれる内容の要旨
7. INSTALLING REFRIGERATOR IN FIG. 5 (One ENCLOSURE each NOTE: DO NOT install the appliance directly on carpeting. Side) Carpeting must be removed or protected by a metal or wood panel beneath the appliance, which extends at least the full width and depth of the appliance. INSTALLATION: The refrigerator must be installed in a substantial enclosure and must be level. When installing the refrigerator in the enclosure, be certain there is a complete seal between the front frame of the refrigerator
ページ5に含まれる内容の要旨
FIG. 6 Heater Rating Plate Flue Baffle Power Protection Module Cover Cover Evaporation Tray 12 V olt Manual G as Drip P an Terminal B lock Shutoff V alve Burner Jet Flexible C ord Inlet F itting 9.TESTING LP GAS SAFETY SHUTOFF The gas safety shutoff must be tested after the refrigerator is connected to LP gas supply. 10. 120 VOLT AC ELECTRICAL To test the gas safety shutoff, proceed as follows: CONNECTION A. Start the refrigerator according to the instructions, with The refrigerator is equipped
ページ6に含まれる内容の要旨
Do not use the chassis or vehicle frame as one of the 13. CHANGING DOOR HINGES FROM conductors. Connect two wires at the refrigerator and route ONE SIDE TO THE OTHER to the DC supply. Open the top door and remove the two screws holding the top decoration. The screws are accessible from beneath. 12.INSTRUCTION FOR MOUNTING DOOR PANEL Remove the top hinge pin and lift out the door. Remove The refrigerator is normally delivered without the door pan- center hinge pin and lift out the lower door. Uns
ページ7に含まれる内容の要旨
SECTION B. CERTIFIED VENT SYSTEM KITS REFRIGERATOR KIT MODEL NO. COMPONENTS PART NO. RM2612 4A ROOF BASE 3103633.XXX * RM2812 ROOF COVER 3103634.XXX * LOWER SIDE VENT 3102277.XXX * POWER VENT POWER VENT ASM. 3104131.002 ** (Island/through ROOF BASE 3103633.XXX * floor) ROOF COVER 3103634.XXX * * Fill in "XXX" with color code numbers. For color codes, contact your supplier. ** Alternate instructions forwarded with the Vent Kit. SECTION C. OPERATING INSTRUCTIONS 1.IMPORTANCE OF LEVELING A R
ページ8に含まれる内容の要旨
2. CONTROL PANEL A B ON CHECK AUTO 1 2 OFF MANUAL LEGEND C 1. Main Power Button ON/OFF 2. AUTO/MANUAL Mode Selector Button A. AUTO Mode indicator Lamp B. CHECK Indicator Lamp (GAS Mode Only) C. Climate Control Switch 3.OPERATING INSTRUCTIONS then ON position. The control system will attempt a A) START-UP INSTRUCTIONS new 45 second ignition sequence. 1) 12 volt DC supply must be available for the electronic 4) On the initial refrigerator start-up on gas (120 volts AC control to function. is not a
ページ9に含まれる内容の要旨
will automatically switch to GAS. As soon as AC This should be considered when placing different types of becomes available again, the control will switch back food in the refrigerator. to AC operation. 3) If the CHECK indicator lamp (B) illuminates, the B. FROZEN FOOD STORAGE COMPARTMENT control has failed to ignite the burner on GAS. To reset Quick frozen soft fruits and ice cream should be placed in the when the CHECK indicator lamp (B) is illuminated, coldest part of the compartment which is
ページ10に含まれる内容の要旨
When all frost is melted, dry the interior of the refrigerator with SECTION D. a clean cloth. Replace all food and start the refrigerator by pressing the ON/OFF button (1) to DOWN position. MAINTENANCE & SERVICE NOTE: On these models the drip tray/cup is on the rear side of the refrigerator. (See FIG. 1) 1.REFRIGERATOR REMOVAL Before working on the refrigerator, make sure the AC voltage Put the plastic drain tube in a watertight bucket or container and DC voltage leads are disconnected. Shut off
ページ11に含まれる内容の要旨
free of soot. Heavy soot formation indicates improper functioning of the burner. The flue and burner both require DO NOT use a wire or pin when cleaning the burner jet cleaning in the following manner: as damage can occur to the precision opening. This can 1) Unplug the refrigerator power cord from the 120 volt cause damage to the refrigerator or create a fire hazard. AC outlet (see FIG. 6). 2) Disconnect or shut off the 12 volt power to the refrigerator. 3) Turn manual shutoff valve to OFF. (Se
ページ12に含まれる内容の要旨
F. FUSES E. Flue baffle not inserted properly in flue tube. The refrigerator is equipped with 2 fuses, one for the F. Improperly set thermostat. refrigerator control system and one for the AC cartridge See Section C. Operating Instructions, Item 3. heater. (See Table below). Paragraph F, and Item 4, Paragraph H. To replace fuse(s) proceed as follows: G. Burner dirty. 1. Disconnect the wall plug, and the 12 volt wires. Clean. See Section D. Maintenance & Service, Item 1. 2. Remove the power modul
