ページ1に含まれる内容の要旨
MULTIPLE COMPACT DISC PLAYER
CD-2280M/DPF-J9010
INSTRUCTION MANUAL
KENWOOD CORPORATION
This unit is designed for home use only. If the unit is
used in a location other than at home, such as in a
shop (for commercial use), in a car or in a ship, etc.,
and is damaged, a service fee may be charged even
during the warranty period.
This instruction manual is used for two models.
Model availability and features (functions) may differ
depending on the country and sales area.
About the DTS multi-channel
ページ2に含まれる内容の要旨
Introduction Introduction CD-2280M/DPF-J9010 (En) Caution : Read this section carefully to ensure safe operation. Before applying power 2 Units are designed for operation as follows. U.S.A. and Canada.................................. AC 120 V only Europe and U.K. ............................................... AC 230 V only Australia .................................................. AC 240 V only Other countries ............... AC 110-120 / 220-240 V switchable For the United Kingdom Factory f
ページ3に含まれる内容の要旨
Introduction CD-2280M/DPF-J9010 (En) Special features 3 CD player with 200-disc changer This unit can accommodate up to 200 discs and can be used like a home jukebox. Multi-room capability This unit consists of two CD player mechanisms and an indepen- dent second output (OUTPUT-B) for simultaneous playback of two discs. This makes it possible to enjoy different music in different rooms, by listening to the playback of a disc on Mechanism-A in Room A and that of a disc on Mechanism-B in Room B, f
ページ4に含まれる内容の要旨
Introduction CD-2280M/DPF-J9010 (En) Unpacking Unpack the unit carefully and make sure that all accessories are put aside so they will not be lost. 4 Examine the unit for any possibility of shipping damage. If your unit is damaged or fails to operate, notify your dealer immediately. If your unit was shipped to you directly, notify the shipping company without delay. Only the consignee (the person or company receiving the unit) can file a claim against the carrier for shipping damage. We recomme
ページ5に含まれる内容の要旨
Introduction CD-2280M/DPF-J9010 (En) 5 Disc handling precautions Never play a cracked or warped disc Handling During playback, the disc rotates at high speed in the player. Therefore, to avoid danger, never use a cracked or deformed disc or a Hold compact discs so that you do not touch the playing surface. disc repaired with tape or adhesive agent. Please do not use discs which are not round because they may cause a malfunction. Label side Playing side Ö Do not attach paper or tape to either the
ページ6に含まれる内容の要旨
System connections System connections CD-2280M/DPF-J9010 (En) Make connections as shown below. Malfunction of microcomputer When connecting the related system components, refer 6 If operation is not possible or erroneous display also to the instruction manuals of the related components. appears even though all connections have been Do not plug in the power lead until all connections are com- made properly, reset the microcomputer refer- pleted. ring to “In case of difficulty”. Ú Be sure to use t
ページ7に含まれる内容の要旨
System connections CD-2280M/DPF-J9010 (En) Connection to digital amplifier or MD (OUTPUT-A only) 7 Connect the DIGITAL OUT (OPTICALor COAXIAL) jack to the digital input jack of the amplifier, DAT recorder, MD recorder, etc., using Optical fiber cable an optical fiber cable or coaxial cable which are commercially avail- able in audio stores. ÖWhen using an optical fiber cable to connect this unit to a digital amplifier, insert the plug straight into the jack until a snap sound is heard. ÖBe caref
ページ8に含まれる内容の要旨
Controls and indicators CD-2280M/DPF-J9010 (En) 8 (The displays given in this manual are approximations only. They may differ Play indicator Text information display from what actually appears on the display.) ¥
¥
¥
¥
¥
¥
¥
¥
¥
¥
¥
¥
¥
¥
¥
Pause indicator DISPLAY 1237 4 5 6 890 ! @ # 1 MULTIPLE COMPACT DISC PLAYER 0
PUSH OPEN DISPLAY-B DISPLAY-A TIMER PLAY OFF ON B A 6 DISC SKIP STANDBY STANDBY OPERATION CONFIRM CONTINUOUS PLAY 7 POWER RANDOM REPEAT DISPLAY 4 ¢
ON/STANDBY ON/STANDBY $ % ^
ページ9に含まれる内容の要旨
Operation of remote control unit (Mechanism-A only) CD-2280M/DPF-J9010 (En) The keys with the same name as those on the main unit operate the same way as on the main unit. The keys marked * are provided only on the remote control unit. The remote control unit controls 9 Mechanism-A regardless of whether the OPERATION A-B indicator on the main unit is lit or not. 1POWER key 6Keys related to program and file registration 2Input keys for numbers and letters * CONTINUOUS SUB OUT * MODE key CONFIRM P
ページ10に含まれる内容の要旨
Preparation Preparation CD-2280M/DPF-J9010 (En) Up to 200 CDs can be loaded in the carousel. Disc exchange also is possible during playback. 10 Never let your hand or any object enter inside the unit. Loading discs in the carousel Switch power ON. 1 STANDBY Press the POWER POWER : Keys and controls used in the operations described on this page. ( ) key. Open the door panel toward the front. 2 Press PUSH OPEN at the right top Ö Do not place any object on the open door panel. of the door panel. Lo
ページ11に含まれる内容の要旨
Preparation CD-2280M/DPF-J9010 (En) 11 Disc replacement Discs can be replaced with the same procedure as “Loading discs in the carousel”. In stopped condition, all discs can be exchanged. However, when the door panel is opened while “DISC DETEC- TION” is being displayed, it may not be possible to remove the disc which had been played. Accordingly, wait for the “DISC DETECTION” indication to go out before opening the door panel. When the disc information has been read in at the time of regis- tra
ページ12に含まれる内容の要旨
Normal play (TRACK mode) (TRACK mode) Normal play CD-2280M/DPF-J9010 (En) 12 Preparation ÖLoad discs into the carousel. 0 ÖSelect the Mechanism-A or Mechanism-B. ! : Keys and controls used in the operations described on this page. Playing tracks in order from track No.1 Use the following procedure to play a CD in the original order of tracks from track No.1. Select the disc. 1 ÖEach press of a key increases (or decreases)the disc number. Holding the key depressed varies the disc numbers success
ページ13に含まれる内容の要旨
Normal play (TRACK mode) CD-2280M/DPF-J9010 (En) Direct disc selection (Mechanism-A only) 13 1 Press the DISC SELECTOR key. Press the numeric keys in the following order... DISC SELECTOR Disc No. 63 : 63 Disc No. 100 : 1)) Ö If the selected disc is being played on Mechanism-B, blinking “DISCXXX BUSY!“ is displayed and the disc will not be played. Within 8 seconds! 2 Input the disc number. How to input numeric values ABC DEF 1 2 3 : Keys and controls used in the operations described on this page.
ページ14に含まれる内容の要旨
Normal play (TRACK mode) CD-2280M/DPF-J9010 (En) 14 Preparation ÖLoad discs into the carousel. 0 ÖSelect the Mechanism-A or Mechanism-B. ! : Keys and controls used in the operations described on this page. Playback from desired track Select the disc. 1 1Select the disc number. Display when disc No. 123 is selected ° DISC SKIP 5 Previous disc Next disc D312 13:2 Within 8 seconds! ÖThe disc number can be selected directly by using the DISC SELECTOR and numeric keys in place of the DISC SKIP keys.
ページ15に含まれる内容の要旨
Displays CD-2280M/DPF-J9010 (En) Displays scrolling Some track titles contain so much text information that the full 15 titles will not fit on the display. In cases like this, the letters on the display move from right to left so that the non-visible part of the title is revealed. This type of display movement is known as “scrolling display.” Display example |Scroll display D3 12GOODLTO DF3AI SHON... D3 12FAISHNODEH : Keys and controls used in the operations described on this page. Track title
ページ16に含まれる内容の要旨
Programming tracks in desired order (PGM mode) (Mechanism-A only) (PGM mode) (Mechanism-A only) Programming tracks in desired order CD-2280M/DPF-J9010 (En) Use the following procedure to select desired tracks (up to 32 tracks) from up to 200 discs and program them in the 16 desired order. Preparation ÖLoad discs into the carousel. 0 ÖSet the Mechanism-A to stop mode. : Keys and controls used in the operations described on this page. Press so that the PGM indicator lights. 1 CHARACTER/ DISPLAY-A
ページ17に含まれる内容の要旨
Programming tracks in desired order (PGM mode) (Mechanism-A only) CD-2280M/DPF-J9010 (En) 17 : Keys and controls used in the operations described on this page. To check the programmed tracks DISPLAY-A SPACE/ P0 GM1DED2000DT3 CHECK Ö Each time the key is pressed, the program No. (P-NO) and the disc No. are displayed. ÖThe previous display resumes in a few seconds. To add a track to the program 1 Set the Mechanism-A to stop mode. Ö When a track No. is entered, the track will be added to the end of
ページ18に含まれる内容の要旨
Programming tracks in desired order (PGM mode) (Mechanism-A only) (REPEAT mode) Repeated playback CD-2280M/DPF-J9010 (En) 18 Preparation ÖLoad discs into the carousel. 0 ÖSelect the Mechanism-A or Mechanism-B. ! : Keys and controls used in the operations described on this page. To repeat only the desired tracks (Mechanism-A only) 1Program the desired tracks by per- ÖUp to 32 tracks can be programmed by repeating steps 1. forming steps 1 to 3 of “Program- ming tracks in desired order”. ^ PGRE EP
ページ19に含まれる内容の要旨
Programming tracks in desired order (PGM mode) (Mechanism-A only) (RANDOM mode) Playback in a random order CD-2280M/DPF-J9010 (En) Use the following procedure to activate random playback which selects a track at random after every track. This fea- 19 ture may allow you to play CDs for long hours without getting tired of. Preparation ÖLoad discs into the carousel. 0 ÖSelect the Mechanism-A or Mechanism-B. ! : Keys and controls used in the operations described on this page. Check that the Mechani
ページ20に含まれる内容の要旨
Registration of Title Name Registration of Title Name CD-2280M/DPF-J9010 (En) For discs not corresponding to CD-TEXT, a title name can be given to the disc (max. 25 characters). Up to 20 tracks 20 titles can be registered per disc. Operation is possible also when the door panel is open. It is convenient to register titles while discs are being inserted. ÖLoad discs into the carousel. 0 Preparation Ö Check that the Mechanism-A is in the normal play TRACK mode. # ÖSet the Mechanism-A to stop mode.
