ページ1に含まれる内容の要旨
CD PLAYER
D-R350
INSTRUCTION MANUAL
KENWOOD CORPORATION
This instruction manual for this model also covers the systems
in the KENWOOD System “SERIES 21” lineup. Since the features
vary depending on the combined systems, the remote control
operation illustrations (icons) are shown for two types of remote
control units.
Refer to the instruction manual included with the AV CONTROL
CENTER for the basic remote control operations.
COMPACT
DIGITAL AUDIO
B60-3276-00 MA ( K, P, T, M, I, X, Y ) I D
98/1
ページ2に含まれる内容の要旨
Introduction D-R350 (En) Caution : Read this section carefully to ensure safe operation. Before applying power 2 Units are designed for operation as follows. U.S.A. and Canada ................................................................ AC 120 V only Europe and U.K. .....................................................................AC 230 V only Australia .................................................................................. AC 240 V only China .................................
ページ3に含まれる内容の要旨
D-R350 (En) Unpacking Unpack the unit carefully and make sure that all accessories are put aside so they will not be lost. 3 Examine the unit for any possibility of shipping damage. If your unit is damaged or fails to operate, notify your dealer immediately. If your unit was shipped to you directly, notify the shipping company without delay. Only the consignee (the person or company receiving the unit) can file a claim against the carrier for shipping damage. We recommend that you retain the or
ページ4に含まれる内容の要旨
System connections D-R350 (En) Malfunction of microcomputer Caution: 4 If operation is not possible or erroneous display appears even Do not plug in the power lead until all connections are com- though all connections have been made properly, reset the pleted. microcomputer referring to “In case of difficulty”. ° Make connections as shown below. When connecting the related system components, refer also to the instruction manuals of the related components. Caution regarding placement To maintain
ページ5に含まれる内容の要旨
System connections D-R350 (En) Connection to a general-use amplifier 5 Use the provided audio cords to connect the OUTPUT jacks of this unit to the CD input jacks (or AUX jacks) of the amplifier. Connection to digital amplifier or MD Connect the DIGITAL OUTPUT (OPTICAL or COAXIAL) jack to the digital input jack of the amplifier, DAT recorder, MD recorder, etc., using an optical fiber cable or coaxial cable which are commercially available in audio stores. ÖWhen using an optical fiber cable to co
ページ6に含まれる内容の要旨
Controls and indicators D-R350 (En) 6 Play indicator (The displays given in this manual are approximations only. Text information display They may differ from what actually appears on the display.) ¥
¥
¥
¥
¥
¥
¥
¥
¥
¥
¥
¥
¥
¥
¥
Pause indicator DISPLAY 125 3 4
6 7
8
DISC 1 2 345 DISC SELECTOR MULTIPLE CD PLAYER D-R350 REPEAT RANDOM 4 ¢
12 3 45 DISC SKIP 0 ON/STANDBY 7 COMPACT COMPACT DIGITAL AUDIO DIGITAL AUDIO TEXT D.R.I.V.E. 6 POWER 9 0 ! ON/STANDBY (For U.S.A. and Canada) The keys with
ページ7に含まれる内容の要旨
Operation of remote control unit D-R350 (En) Remote Control Unit (RC) 7 A remote control unit is not included with this unit. However, a remote control is supplied with the KENWOOD SERIES 21 “AV CONTROL CENTER” (sold separately). To enable remote control operation, simply connect this unit, cassette deck (sold separately), and other accessories to the AV CONTROL CENTER with the system control cords. The keys with the same name as those on the main unit oper- ate the same way as the main unit. Th
ページ8に含まれる内容の要旨
Operation of remote control unit D-R350 (En) Graphical Remote Control Unit (GRC) 8 A remote control unit is not included with this unit. However, a remote control is supplied with the KENWOOD SERIES 21 “AV CONTROL CENTER” (sold separately). To enable remote control operation, simply connect this unit, cassette deck (sold separately), and other accessories to the AV CONTROL CENTER with the system control cords. 4 3 5 Input Main Menu ENTER Source CD Tuner LD Tape1 TapeA 1 Return Set Up Confirm Cab
ページ9に含まれる内容の要旨
Operation of remote control unit D-R350 (En) ¦ Turn the system devices ON. Preparation 9 Input Main Menu ENTER CD Tuner LD Tape1 TapeA Source You may skip Step 1 if the settings for the AV CONTROL CENTER Return Set Up Confirm Cable Sat. TV VCR1 VCR2 TapeB VOLUME CD have already been made. Track 00 MUTING Disc Skip 10key Mode Pad Disc 0 Once the settings have been made in Steps 1 to 3, you do not ON /STANDBY REMOTE CONTROL UNIT need to repeat these steps until you replace the batteries. GRC opera
ページ10に含まれる内容の要旨
Operation of remote control unit D-R350 (En) 10 Input Main Menu ENTER CD Tuner LD Tape1 TapeA Source Return Set Up Confirm Cable Sat. TV VCR1 VCR2 TapeB VOLUME CD Track 00 MUTING Disc Skip 10key Mode Pad Disc 0 ON /STANDBY REMOTE CONTROL UNIT Graphical Remote Control Unit (GRC) This instruction manual for this model also covers the systems in the KENWOOD System “SERIES 21” lineup. Since the features vary depending on the combined systems, the remote control operation illustrations (icons) are sh
ページ11に含まれる内容の要旨
Preparing to Play Tracks D-R350 (En) Ö Turn the unit ON. Preparation 11 (For U.S.A. and Canada) (For other countries) POWER ON/STANDBY ON/STANDBY GRC operation : Complete the procedure in “Basic Operations for the Graphical Remote Control Unit (GRC)” 90 : Keys and control used in the operations described on this page. Loading/unloading discs Load/unload a disc. 1 1Open the tray. 0 Ö Do not touch the played side of disc. 2Place/remove a disc. ÖLoading two discs together will cause malfunctioning
ページ12に含まれる内容の要旨
Normal play (TRACK mode) D-R350 (En) Use the following procedure to play a CD in the original order of tracks from track No. 1. 12 Ö Load a disc in the CD player. Preparation GRC operation : Complete the procedure in “Basic Operations for the Graphical Remote Control Unit (GRC)” 90 : Keys and control used in the operations described on this page. Playing tracks in order from track No. 1 Check that the unit is in the normal play TRACK 1 mode. # Start playback. 2 Blinks during playback. Select
ページ13に含まれる内容の要旨
Normal play (TRACK mode) D-R350 (En) Remote control unit only Playback from desired track 13 RC operation GRC operation 1 Select the disc. DISC SKIP Disc Skip ENTER REPEAT 2 Select the desired track No. RC operation Press the numeric keys as shown below.... 10key To enter track No. 23 : 003 +10 Pad To enter track No. 40 : 0000) ENTER 1 2 3 4 5 1 2 3 6 7 8 9 0 GRC operation 4 5 6 Press the ENTER key after selecting each numeric icon. 7 8 9 To enter track No. 23 : 0ENTER, 0ENTER, 3ENTER 0 +10 ÖWh
ページ14に含まれる内容の要旨
Searching for tracks by title (TITLE SEARCH) D-R350 (En) In the case of a CD-TEXT disc, the tracks to be heard can be searched by title. 14 ÖLoad a disc (CD-TEXT support) in the CD Preparation player. ÖCheck that the unit is in the normal play TRACK mode. # Ö Press the ALL TEXT SEARCH key. ! GRC operation : Complete the procedure in “Basic Operations for the Graphical Remote Control Unit (GRC)” : Keys and control used in the operations described on this page. 90 Press the TITLE SEARCH key. 1 Bli
ページ15に含まれる内容の要旨
Displays D-R350 (En) Remote control unit only Time display on CD player (TIME DISPLAY) 15 Each press of the TIME key changes the displayed contents. 1 : Elapsed time of track being played 12:3 RC operation GRC operation 2 : Remaining time of track being played -3 2:7 Mode 3 : Elapsed time of entire disc (T lights up.) TIME 24 3:5T ENTER 4-632:5T : Remaining time on entire disc (T lights up.) Time ENTER Ö Only the display 1 and 2 will be displayed in PGM, RANDOM and Do this operation in the play
ページ16に含まれる内容の要旨
Programmed play (PGM mode) D-R350 (En) Use the following procedure to program desired tracks in a desired order. (Up to 32 tracks) 16 Ö Load a disc in the CD player. Preparation Ö Set the INPUT SELECTOR to ”CD“ on the connected device such as AV CONTROL CENTER or receiver. GRC operation : Complete the procedure in “Basic Operations for the Graphical Remote Control Unit (GRC)” 90 : Keys and control used in the operations described on this page. Press so that the “PGM” indicator lights. 1 RC oper
ページ17に含まれる内容の要旨
Programmed play (PGM mode) D-R350 (En) To check or change the programmed tracks 17 Blinks. RC operation GRC operation 1 Press the CHECK key. P0 GM1 D5TN2 O.5 CHECK Check ENTER Press until the track No. to ÖPerform only step 1 to simply check the program. be changed is displayed. Ö In the case of a CD-TEXT disc, the track’s title is scrolled on the display. 2 Select the disk. Ö Each time the key is pressed, the program No. and the track No. on CD DISC SKIP Disc Skip are displayed. ENTER REPEAT 3
ページ18に含まれる内容の要旨
Repeated playback D-R350 (En) Ö Load a disc in the CD player. Preparation 18 Ö Set the INPUT SELECTOR to ”CD“ on the connected device such as AV CONTROL CENTER or receiver. : Complete the procedure in “Basic Operations GRC operation for the Graphical Remote Control Unit (GRC)” 90 : Keys and control used in the operations described on this page. To repeat only the programmed tracks RC operation GRC operation 1 Press so that the “PGM” indicator lights. Mode ENTER P0 GM1DC IS? P.MODE PGM ENTER P.m
ページ19に含まれる内容の要旨
Repeated playback D-R350 (En) 19 To repeat the entire disc This allows repeated playback of all the tracks on the disc loaded in the disc tray. RC operation GRC operation 1Press so that the “PGM” indicator goes off. \ P0 GM1 01 Mode P.MODE ENTER PGM ENTER P.mode ENTER 2Switch REPEAT ON. Return REPEAT RE EPTAON ENTER Repeat ENTER Main unit operation GRC operation The current status is displayed when the key is pressed To display the current status, first select the Return icon and press once. Wh
ページ20に含まれる内容の要旨
Editing D-R350 (En) The following procedure allows to record a CD within the specified tape length so that no music is interrupted in the middle at the ends of sides A and B. 20 Ö Load a disc in the CD player. Preparation ÖCheck that the unit is in the normal play TRACK mode. # Ö Set the INPUT SELECTOR to ”CD“ on the connected device such as AV CONTROL CENTER or receiver. GRC operation : Complete the procedure in “Basic Operations : Keys and control used in the operations described on this page
