ページ1に含まれる内容の要旨
2104045
LOADER MOUNTING KIT
for LS84 Loader
®
on Kubota
B3200 Tractors
B3300SU Tractors
Includes Hose Kit
1019695
Tested. Proven. Unbeatable.
SAVE THIS
MANUAL!
Include it with
your Loader Manual.
It contains safety,
operation, and repair
part information
not found in other
manuals.
MAN0807
(Rev. 4/25/2011)
INSTALLATION MANUAL
ページ2に含まれる内容の要旨
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Make sure that all operating and service person- ! nel know that if hydraulic fluid penetrates skin, it LEA EL INSTRUCTIVO! must be surgically removed as soon as possible by Si no lee Ingles, pida ayuda a a doctor familiar with this form of injury or gan- alguien que si lo lea para que le grene, serious injury, or death will result. CON- traduzca las medidas de seguridad. TACT A PHYSICIAN IMMEDIATELY IF FLUID ENTERS SKIN OR EYES.
ページ3に含まれる内容の要旨
LOADER MOUNT INSTALLATION CAUTION ■ Only use 2104045 Loader Mounting Kit for Always wear relatively tight and belted clothing ® mounting Woods LS84 loader on Kubota B3200 to avoid getting caught in moving parts. Wear and B3300SU tractors. Any other use or modifica- sturdy, rough-soled work shoes and protective tion of this mounting kit may result in serious equipment for eyes, hair, hands, hearing, and head; injury or death. and respirator or filter mask where appropriate. Safety ins
ページ4に含まれる内容の要旨
Attach Right and Left loader Mounts 1. Attach right loader mount (1) to tractor frame using two cap screws (10) and hardened flat washers (12) in the forward top holes. 11 12 10 2. Insert cap screw (11) and hardened flat washer 12 (12) in the third and fourth hole. 3. Insert flange head cap screw (7) into the three 10 holes in tractor clutch housing. Use cap screw (6) Tractor 12 and washer (8) in the top rear slots to connect Hardware 13 loader mount to tractor frame. For three lower slots, u
ページ5に含まれる内容の要旨
Install Grill Guard (Optional) 1. Attach grill guard (20) to front of tractor frame using cap screws (10), hardened flat washers (12), and hex nuts (13) as shown in Figure 4. 2. Torque hardware to: M14-1.5P x 40mm HHCS . . . 87 lbs-ft (118 N-m) 20. 1031140 Grill guard (includes items 10, 12 & 13) 10. 64127 M14 x 1.5P x 40 mm HHCS 12. 46070 9/16 Hardened Flat Washer 13. 43104 M14 x 1.5P Hex Nut Figure 4. Grill Guard Installation Mount Installation 5 MAN0807 (6/17/2009)
ページ6に含まれる内容の要旨
1019695 HOSE KIT INSTALLATION Keep hands and body away from pressurized Protective hose sleeves must cover all hydrau- lines. Use paper or cardboard, not hands or other lic hoses within 20 inches of the operator and be body parts to check for leaks. Wear safety goggles. secured onto metal hose fittings. Replace hoses or Hydraulic fluid under pressure can easily penetrate sleeves if damaged or if protective sleeve cannot skin and will cause serious injury or death. be properly
ページ7に含まれる内容の要旨
Attach Loader Supply Hoses 1. Attach female quick couplers (2) to the loader 1. 360220 Hose, 38" x 1/4 NPTM x 9/16 JICM supply hoses (1). 2. 1019696 Quick coupler, female 2. Attach loader supply hoses to the loader steel feedlines on the loader boom. See Figure 6. Figure 6. Loader Feedline Connections Connect Loader Supply Hoses 3. Hoses must be routed so that they are not 1. Route hydraulic hoses along loader mount and pinched, bent sharply, or chafed during operation. connect to tractor h
ページ8に含まれる内容の要旨
Verify Control Movements 1. Mount loader to tractor: Remove mount pins from loader uprights. Align tractor with loader and slowly drive tractor into loader. Shut off tractor. 2. Connect loader feedline hoses to tractor hydraulic couplers. See Figure 7. 3. Comply with all safety rules and start the tractor. 4. Mount loader to tractor by activating bucket cylin- ders to raise or lower the loader uprights into the loader mounts. Slowly advance tractor forward, activating appropriate cylinders t
ページ9に含まれる内容の要旨
NOTES 9 Hydraulic Installation MAN0807 (6/17/2009)
ページ10に含まれる内容の要旨
2104045 LOADER MOUNTING KIT REF PART QTY DESCRIPTION REF PART QTY DESCRIPTION 1 1030978 1 Right Mount 10 64127 12 M14 x 1.5P x 40 mm HHCS 2 1030979 1 Left Mount 11 65541 4 M14 X 1.5P x 50 mm HHCS 3 1030986 1 Center Plate 12 46070 20 9/16 Hardened Flat Washer 6 65505 5 12 mm-1.25P x 30 mm HHCS 13 43104 8 M14 x 1.5 Hex Nut 7 1028293 12 M12-1.75x35 CL10.9 Hex flange screw 20 1031140 1 Grill Guard (optional) (includes items 10, 12, & 13) 8 52177 5 .488 x 1.25 x .134 HT washer 9 1028338 6 M12-1.75 CL
ページ11に含まれる内容の要旨
1019695 HOSE KIT REF PART QTY DESCRIPTION 1 360220 4 Hose, 38" x 1/4 NPTM x 9/16 JICM 2 1019696 4 Quick coupler, female 3 395061 1 Plastic band, red (not shown) 4 395062 1 Plastic band, blue (not shown 5 56061 1 Plastic band, green (not shown) 6 56062 1 Plastic band, yellow (not shown) 7 54124 1 Plastic band, white (not shown) 8 88 * 2 Plastic tie, (not shown) * Standard hardware, obtain locally 11 Parts MAN0807 (6/17/2009)
ページ12に含まれる内容の要旨
BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application. Fasteners must always be replaced with the same grade as specified in the manual parts list. Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware. Make sure fastener threads are clean and you start thread engagement properly. All torque values are given to specifications used on hardware define
ページ13に含まれる内容の要旨
BOLT SIZE CHART NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts. SAE Bolt Thread Sizes 5/16 3/8 1/2 5/8 3/4 7/8 IN 1 2 7 34 5 6 MM 25 50 75 100 125 150 175 Metric Bolt Thread Sizes 8MM 10MM 12MM 14MM 16MM 18MM ABBREVIATIONS AG .............................................................. Agriculture MPa ........................................................ Mega Pascal ASABE ....................American Society of Agricultural & N .
ページ14に含まれる内容の要旨
WARRANTY TM All Models Except Mow’n Machine Zero-Turn Mowers Please Enter Information Below and Save for Future Reference. Date Purchased: ____________________________ From (Dealer): __________________________________________ Model Number: ____________________________ Serial Number: __________________________________________ Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and workmanship. Except as otherwise set forth below, the duration of this Warrant
ページ15に含まれる内容の要旨
WARRANTY TM (Replacement Parts For All Models Except Mow’n Machine TM Zero-Turn Mowers and Woods Boundary Utility Vehicles) Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and workmanship for a period of ninety (90) days from the date of delivery of the product to the original purchaser with the exception of V-belts, which will be free of defect in material and workmanship for a period of 12 months. Under no circumstances will this Warranty apply in th
ページ16に含まれる内容の要旨
MAN0807 Woods Equipment Company 2606 South Illinois Route 2 Post Office Box 1000 Oregon, Illinois 61061 815-732-2141 tel 815-732-7580 fax www.WoodsEquipment.com © 1994 Woods Equipment Company. All rights reserved. WOODS, the Woods logo, and "Tested. Proven. Unbeatable." are trademarks of Woods Equipment Company. All other trademarks, trade names, or service marks not owned by Woods Equipment Company that appear in this manual are the property of their respective companies or mark holders. Spec
