ページ5に含まれる内容の要旨
2. Place the battery. Preparing the remote controller Slide the battery into the holder with the + side facing upwards so that the battery is fixed in This section is only for KD-SX992R. the holder. Lithium coin battery (product number: KD-SX921R can also be remotely controlled with CR2025) an optionally purchased remote controller. We recommend that you use remote controller RM-RK50 with your unit. Before using the remote controller: • Aim the remote controller directly at the remote sensor on
ページ6に含まれる内容の要旨
3 • Selects the preset stations while listening to Remote controller the radio (or the DAB tuner). Each time you press the button, the preset This section is only for KD-SX992R. station (or service) number increases, and the selected station (or service) is tuned in. KD-SX921R can also remotely controlled with an • Skips to the previous disc while listening to optionally purchased remote controller. We the CD changer. recommend that you use remote controller Each time you press the button, the d
ページ7に含まれる内容の要旨
BASIC OPERATIONS 3 12 Turning on the power 3 Adjust the volume. To increase the volume. 1 Turn on the power. “HELLO” appears on the display. To decrease the volume. Volume or audio level Note on One-Touch Operation: indicator (see page 27) When you select a source in step 2 below, the Volume level appears power automatically comes on. You do not have to press this button to turn on the power. 2 Select the source. To select the tuner, press FM AM repeatedly. 4 Adjust the sound as you want. FM1 FM
ページ8に含まれる内容の要旨
RADIO OPERATIONS Listening to the radio 2 Start searching a station. Press ¢ to search You can use either automatic searching or manual stations of higher searching to tune in to a particular station. frequencies. Searching a station automatically: Auto search Press 4 to search stations of lower frequencies. 1 Select the band (FM1 – 3, AM). When a station is received, searching stops. To stop searching before a station is received, press the same button you have pressed for FM1 FM2 FM3 AM sear
ページ9に含まれる内容の要旨
• If you release your finger from the button, Searching a station manually: the manual mode will automatically turn off Manual search after 5 seconds. • If you hold down the button, the frequency 1 Select the band (FM1 – 3, AM). keeps changing (in 50 kHz intervals for FM and 9 kHz intervals for AM – MW/LW) until you release the button. FM1 FM2 FM3 AM When an FM stereo broadcast is hard to (F1) (F2) (F3) receive: 1 Press MODE to enter the functions mode while listening to an FM Note: stereo broad
ページ10に含まれる内容の要旨
Manual preset Storing stations in memory You can preset up to 6 stations in each band (FM1, You can use one of the following two methods to FM2, FM3 and AM) manually. store broadcasting stations in memory. Ex.: Storing an FM station of 88.3 MHz into the • Automatic preset of FM stations: SSM (Strong- preset number 1 of the FM1 band station Sequential Memory) • Manual preset of both FM and AM stations 1 Select the band (FM1 – 3, AM) you want to store stations into (in this FM station automatic pr
ページ11に含まれる内容の要旨
Tuning in to a preset station 3 Press and hold the number button (in this example, 1) for more than 2 You can easily tune in to a preset station. seconds. Remember that you must store stations first. If you have not stored them yet, see “Storing stations in memory” on pages 10 and 11. 1 Select the band (FM1 – 3, AM). FM1 FM2 FM3 AM (F1) (F2) (F3) Selected band/preset number and “MEMO” (memory) appear alternately for a while. 2 Select the number (1 – 6) for the preset station you want. 4 Repeat t
ページ12に含まれる内容の要旨
RDS OPERATIONS To use Network-Tracking Reception What you can do with RDS You can select the different modes of network- tracking reception to continue listening to the RDS (Radio Data System) allows FM stations to same programme in its finest reception. send an additional signal along with their regular When shipped from the factory, “AF” is selected. programme signals. For example, the stations send their station names, as well as information about • AF: Network-Tracking Reception is what type
ページ13に含まれる内容の要旨
Using TA Standby Reception 1 Press and hold SEL (select) for more than 2 seconds so that one of the TA Standby Reception allows the unit to switch PSM items appears on the display. temporarily to Traffic Announcement (TA) from the (PSM: see page 26.) current source (another FM station, CD or other connected components). • TA Standby Reception will not work if you are listening to an AM station. 2 Select “AF-REG (alternative frequency/regionalization reception)” if not shown on the display. 7 Whe
ページ14に含まれる内容の要旨
Using PTY Standby Reception 4 Finish the setting. PTY Standby Reception allows the unit to switch temporarily to your favourite programme (PTY: Programme Type) from the current source (another FM station, CD or other connected components). • PTY Standby Reception will not work if you are listening to an AM station. 7 When the current source is FM, the PTY indicator either lights up or flashes. To select your favourite programme for • If the PTY indicator lights up, PTY PTY Standby Reception Stan
ページ15に含まれる内容の要旨
Searching your favourite programme 2 Select one of the twenty-nine PTY codes. (See page 18.) You can search any one of the PTY codes. In addition, you can store your 6 favourite Selected code name programme types in the number buttons. appears on the display. When shipped from the factory, the following 6 programme types have been stored in the number buttons (1 to 6). To store your favourite programme types, see below. To search your favourite programme type, see page 16. 3 Press and hold the n
ページ16に含まれる内容の要旨
To search your favourite programme type Other convenient RDS functions and adjustments 1 Press and hold TP PTY for more than 2 seconds while listening to an FM station. Automatic selection of the station when using the number buttons Usually when you press the number button, the preset station is tuned in. However, when the preset station is an RDS station, something different will happen. If the signals from that preset station are not sufficient for good reception, this unit, using the AF data
ページ17に含まれる内容の要旨
Changing the display mode while Setting the TA volume level listening to an FM station You can preset the volume level for TA Standby Reception. When a traffic programme is received, You can change the initial indication on the display the volume level automatically changes to the preset to station name (PS NAME), station frequency level. (FREQ) or while listening to an FM RDS station. • See also “Changing the general settings (PSM)” • See also “Changing the general settings (PSM)” on page 25. o
ページ18に含まれる内容の要旨
PTY codes NEWS: News CHILDREN: Entertainment programmes for AFFAIRS: Topical programmes expanding children on current news or affairs SOCIAL: Programmes on social activities INFO: Programmes which impart advice RELIGION: Programmes dealing with any on a wide variety of topics aspect of belief or faith, or the SPORT: Sport events nature of existence or ethics EDUCATE: Educational programmes PHONE IN: Programmes where people can DRAMA: Radio plays express their views either by CULTURE: Programmes
ページ19に含まれる内容の要旨
CD OPERATIONS The CD–in indicator lights up. Playing a CD 1 Open the control panel. Total playing time of Total track number the inserted disc of the inserted disc Note: When an external component is connected to the AUX jack in the control panel, be careful of handling a CD. Elapsed 2 Insert a disc into the loading slot. playing time Current track The unit turns on, draws the disc and starts playback automatically. Source indication will change to the clock time if “CLOCK” is set to “ON”. (See
ページ20に含まれる内容の要旨
To stop play and eject the disc To go to a particular track directly Press 0. CD play stops, the control panel opens, then the disc automatically ejects from the loading slot. If you change the source, the CD play also stops (without ejecting the disc this time). Press the number button corresponding to the Notes: track number to start its playback. • If the ejected disc is not removed for about 15 • To select a track number from 1 – 6: seconds, the disc is automatically inserted again Press 1 (
ページ1に含まれる内容の要旨
CD RECEIVER
CD-RECEIVER
RECEPTEUR CD
CD-RECEIVER
KD-SX992R/KD-SX921R
KD-SX992R
ATT SOUND
KD-SX992R
U
DAB
R SOURCE F
D
EQ
VOL VOL
TP
PTY
KD-SX921R
KS-SX921R
DAB
EQ
TP
PTY
For installation and connections, refer to the separate manual.
Für den Einbau und die Anschlüsse siehe das eigenständige Handbuch.
Pour l’installation et les raccordements, se référer au manuel séparé.
Bijzonderheden over de installatie en aansluiting van het apparaat vindt u in de desbetreffende
handleiding.
INSTRUCTIONS
BEDI
ページ2に含まれる内容の要旨
Position And Reproduction Of Labels Bottom panel of the main unit CAUTION: Invisible laser ADVARSEL: Usynlig laser - VARNING: Osynlig las er- VARO: Avattaessa ja suo- radiation when open and stråling ved åbning, når strålning när denna del jalukitus ohitettaessa olet interlock failed or d efeated . sikkerhedsafbrydere er ude är öppnad och spärren är alttiina näkymättömälle AVOI D DIRECT EXPOSURE af funktion. Undgåudsæt- urkopplad. Betrakta ej lasersäteilylle. Älä katso strålen.
ページ3に含まれる内容の要旨
Thank you for purchasing a JVC product. Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best possible performance from the unit. CONTENTS How to reset your unit ............................... 2 SOUND ADJUSTMENTS .................. 22 How to use the MODE button ................... 3 Adjusting the sound ................................. 22 Selecting preset sound modes LOCATION OF THE BUTTONS ............ 4 (C-EQ: custom equalizer) .
ページ4に含まれる内容の要旨
LOCATION OF THE BUTTONS Control panel Display window s d f g h jk l / z x 12437 56 8 9 p q w e r t yui o ; a 14 /¢ buttons ; TP PTY (traffic programme/programme type) 25 (up) button button 3° (down) button a AUX (auxiliary) input 4 Remote sensor 5 Display window Display window 60 (eject) button s Main display 7 FM AM button d Volume (or audio) level indicator 8 CD CD-CH (AUX) button Equalization pattern indicator 9 (standby/on/attenuator) button f Tuner reception indicators p (control panel rel
