Clam Corp Fish Trap X2 8237の取扱説明書

ページ1に含まれる内容の要旨

M o d e l N o .

- 8 2 3 7 -


( p / n 1 0 8 3 2 6 )
S p e c i f i c a t i o n s
H e i g h t – 7 5 ” ( 2 5 ” p a c k e d )
▪
W i d t h - 7 5 i n c h e s
▪
▪ D e p t h – 9 0 ” ( 4 2 ” p a c k e d )
Weight - 1 4 5 l b s
▪
I n s t r u c t i o n p / n 1 0 2 4 8 3
▪


























- Clam Customer Servi ce Information -

NOTICE!! - ONCE USED, THIS SHELTER CANNOT BE RETURNED TO THE STORE. IF YOU HAVE
A WARRANTY CLAIM, HAVE YOUR SALES RECEIPT READY

ページ2に含まれる内容の要旨

- Parts Diagram (Seating) – ITEM QTY P/N DESCRIPTION ITEM QTY P/N DESCRIPTION 1 8 101048 BLOCK, SLIDE 18 2 101813 BRACKET, RAIL HANGER 2 16 101081 WASHER, ¼ FLAT 19 2 101817 BRACKET, FRONT SEAT 3 34 101082 LOCKNUT, ¼” THIN 20 6 101829 ASSY, STRAIGHT CANOPY POLE 4 8 101088 SCREW, ¼” X ¾” PHILLIPS 21 2 101830 ASSY, BENT CANOPY POLE 5 4 101146 ANGLE, 1-1/2” X 1-3/4” X 9” ALUM 22 2 101836 ASSY, FRONT SPREADER POLE 6 8 101147 SCREW, #10 x 1” LONG PHILLIPS 23 2 101839 ASSY, ROOF SPREADER POLE

ページ3に含まれる内容の要旨

- Parts Diagram (Shelter) - 3

ページ4に含まれる内容の要旨

- Step 0ne - 4

ページ5に含まれる内容の要旨

- Step Two - 5

ページ6に含まれる内容の要旨

- Step Three - 6

ページ7に含まれる内容の要旨

- Step Four - Rear Seat Bracket (p/n 102430) Latch Clip (p/n 102512) 7

ページ8に含まれる内容の要旨

- Step Five - X2 Base (p/n 102500) 8

ページ9に含まれる内容の要旨

- Step Si x - 9

ページ10に含まれる内容の要旨

- Step Seven - 10

ページ11に含まれる内容の要旨

- Step Ei ght - X2 Tent (p/n 102437) 11

ページ12に含まれる内容の要旨

- Step Nine - 12

ページ13に含まれる内容の要旨

- Step Ten - 13

ページ14に含まれる内容の要旨

- Seating Installation - Angle the seat assembly slightly while placing the bottom lip of the front seat bracket under the outside edge of the base lip. With the latch clip hanging freely, tilt the complete assembly downward until the interior of the rear seat bracket surrounds the support tube. 14

ページ15に含まれる内容の要旨

- Seating Install ati on (cont .) - Reach under the rear seat bracket and slide the latch clip outwards and then up against the underside of the support tube. Squeeze the latch clip into the horizontal slot of the rear seat bracket. Secure the position of the latch clip by pushing it into the two holes located above the horizontal slot of the rear seat bracket. WARNING: ALWAYS KEEP THE LATCH CLIP IN THE SECURED POSITION DURING USE. FAILURE

ページ16に含まれる内容の要旨

- Tips for Use - Folding and transporting your Fish Trap is easy: Unsnap the roof spreader poles, rear spreader poles, and front spreader poles. Lay them in the ▪ bottom of the base. Push the spring buttons and retract each hoop, starting with the rear hoop and working towards the ▪ front. Rotate all retracted hoops to the resting position. Tuck the tent into the base and between the hoops so that no material is left hanging on the ground for transport. Cover with the Travel Cove