ページ1に含まれる内容の要旨
English Español Português Italiano Deutch Français
M
INSTRUCTION MANUAL
FOR
DIGITAL BLOOD PRESSURE MONITOR
MODEL CH-656C
- Eng 1 -
ページ2に含まれる内容の要旨
CLEANING METHOD OF CUFF After cleaning the cuff with a neutral detergent, will cause air leakage. Also, be careful not to get lightly rinse it with water and let it dry in the air. water into the air hose. Hard rubbing or washing in a washing machine GENERAL REMARKS • The blood pressure varies constantly throughout the General Remarks on blood day. Measurement should be made regularly at the pressure measurement same time each day. • If the cuff is to be deflated quickly, depress • Do NOT be im
ページ3に含まれる内容の要旨
English Español Português Italiano Deutch Français For proper measurement of blood • When you feel like relieving yourself, you should do so before measuring blood pressure. pressure • Measure blood pressure where the room tem- • Take a deep breath five or six time and then perature is about 20˚C. Do NOT measure blood relax before measuring blood pressure. If you pressure when it is too cold (below 10˚C) or are tense when taking the measurement, you too hot (above 40˚C) in the room. will not ge
ページ4に含まれる内容の要旨
• Congestion, swelling, etc. may occur in some Nature and frequency of people. maintenance: • If blood pressure is measured repeatedly, an This products is designed for use over an ex- accurate result will not be achieved. An inter- tended period of time; however, it is generally val of about 10 minutes should be allowed. recommended that it be inspected every two • The memory is erased if the batteries are re- years to ensure proper function and performance. moved for replacement, etc. and a re
ページ5に含まれる内容の要旨
English Español Português Italiano Deutch Français M IDENTIFICATION OF PARTS Diastolic blood pressure/ Pulse display section Systolic blood pressure display section Battry cover Power/Start switch Memory recall switch Wrist cuff - Eng 5 -
ページ6に含まれる内容の要旨
BATTERY REPLACEMENT 1. To use this unit, you must install batteries, and also If battery mark “ ” will display on the display, you must change two pieces of batteries. 2. Open battery cover as illustrated. Replace the new two pieces of batteries, matching the (+) and (–) polarities on each battery with the polarity marks on the case. 3. “LR03” batteries or equivalent is suitable for • Pull the transparent ribbon to remove the bat- this blood pressure meter. teries. MEASUREMENT PROCEDURES 1. At
ページ7に含まれる内容の要旨
English Español Português Italiano Deutch Français • Apply the wrist cuff to the wrist and make sure Measurement Procedures for it is not too loose or too tight. If the wrist cuff People With a Weak Pulse is applied inappropriately, it may display an • Apply the middle part of the wrist cuff to the error or abnormal values. artery in the wrist to measure blood pressure. Pull the wrist tight and close the “Burr closure”. Wrist circumference: 13.5-19.5 cm. 2. To start the Measurement CAUTION Press
ページ8に含まれる内容の要旨
The heart symbol flashes, and the buzzer sounds When a pulse is detected, the pressure value for 1 second. Once the measurement prepara- moves to the lower side of the display. At this tions are completed, the buzzer sounds three time the mark “Q” flashes and buzzer beeps. more times. If batteries become weak, “ ” mark is dis- played and measurement is discontinued. Once the blood-pressure measurement has sta- bilized, pressurization is discontinued, the air in the cuff is automatically let ou
ページ9に含まれる内容の要旨
English Español Português Italiano Deutch Français When there are already 7 sets of results in 3. Turn Power off memory, the oldest one is automatically erased and overwritten with the newest. (2 second) (1 second) Blood pressure values and pulse rate display al- ternatively on the display. Display of the mea- surement result will continue until power is Press the “POWER/START” switch to turn off. turned off. CAUTION To discontinue a measurement for any reason, press the “POWER/START
ページ10に含まれる内容の要旨
M 5. Memory recall • When pressing the “Memory recall” switch, the memory cell number is displayed, then the stored measurement results (high/low blood pressure) are displayed. • You can recall stored data by pressing the “Memory recall” switch, except when per- forming a measurement. • Up to 7 sets of measurement results can be stored in memory, and memory cell No. 1 is always used to store the newest set of re- • If the “Memory recall” switch is pressed fur- sults. ther, the old date are indic
ページ11に含まれる内容の要旨
English Español Português Italiano Deutch Français M 6. Memory clear function While the memory datum to be cleared are in- dicated and when the “Memory recall” switch is continued to push for 3 seconds, buzzer beeps and the memory datum are cleared. - Eng 11 -
ページ12に含まれる内容の要旨
DESCRIPTION OF DISPLAY MARKS DISPLAY MARK CONDITION / CAUSE CORRECTIVE ACTION The cuff was inflated to more than 280 Exhaust the air with in the cuff. mmHg. Pressurization is not possible After winding the cuff over again, re- Cuff winding has not been performed peat measurement. correctly. The pulse could not be measured ac- After again winding the cuff, conduct curately. the measurement without moving. Repeat the measurement without mov- The arm moved during measurement. ing the arm. Device ha
ページ13に含まれる内容の要旨
CITIZEN is a registered trademark of Citizen Watch Co., Japan. Consumer Electronics Division CBM Bldg. 5F, 5-68-10, Nakano, Nakano-ku, Tokyo 164-0001, Japan Phone: (03)5345-7430 Fax: (03)5345-7431 E-mail: info-con@jcbm.co.jp
