ページ1に含まれる内容の要旨
T4261 T4261
Please keep this instruction sheet for future reference, Please keep this instruction sheet for future reference,
as it contains important information. as it contains important information.
R Requires three “AA” (LR6) alkaline batteries (not included) for operation. equires three “AA” (LR6) alkaline batteries (not included) for operation.
Adult assembly is required. Adult assembly is required.
T To ool required for assembly: Phillips screwdriver (not included). ol required for as
ページ2に含まれる内容の要旨
Assembled Parts Assembled Parts CAUTION This package contains small parts in its unassembled state. Adult assembly is required. Upper Wall Lower Wall 2 Bases 8 Ramps Ramp Ramp Top Ramp 2 Balconies Car Lift Elevator (Labeled 1) (Labeled 2) (Labeled 3) #8 x ⅝ ” Screw – 7 Shown Actual Size The screw is shown actual size. Tighten or loosen all screws with a Phillips screwdriver. Do not over-tighten the screws. Fisher Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A. T426
ページ3に含まれる内容の要旨
Battery Installation Battery Safety Information In exceptional circumstances, batteries may leak fluids that can 1,5V x 3 cause a chemical burn injury or ruin your product. To avoid “AA” (LR6) battery leakage: • Do not mix old and new batteries or batteries of different types: alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium). • Insert batteries as indicated inside the battery compartment. • Remove batteries during long periods of non-use. Always remove exhausted batteries f
ページ4に含まれる内容の要旨
Consumer Information FCC Statement (United States Only) CONSUMER ASSISTANCE This equipment has been tested and found to comply with the 1-800-432-5437 (US & Canada) limits for a Class B digital device, pursuant to Part 15 of the 1300 135 312 (Australia) FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accorda
ページ5に含まれる内容の要旨
Assembly Walls 1 • Fit the upper and lower walls together, as shown. Bases 3 • Place the bases on a flat surface, as shown. • Fit the wall assembly into each base and push to “snap” in place. Hint: The wall is designed to fit the bases one way. If it does not seem to fit, turn or switch one or both bases around and try again! Blue Dots T Top View op View 4 Screws 2 Ramp Labeled 2 • Insert four screws into the holes in the wall assembly and tighten. 4 • Locate the ramp labeled with a 2. • Fit
ページ6に含まれる内容の要旨
Assembly Green Dots Ramps Labeled 1 T Top View op View Ramp Labeled 3 BACK FRONT 5 7 • Locate the ramp labeled 3. • Carefully turn the assembly around. • Fit the ends of the ramp into the slots in the wall and base, • Fit the ends of the three ramps labeled 1 into the slots in the wall, as shown. as shown. Hint: The tab at the top of the ramp has a green dot on it. Match • While holding each ramp in place, push the ramps on both sides this dot to the slot with the green dot. of the wall to
ページ7に含まれる内容の要旨
Assembly Elevator Car Lift 9 • Fit the tabs on the car lift into the slots on the wall, as shown. 11 • Slide the elevator onto the end of the wall assembly, as shown. 3 Screws Top Ramp Balconies 10 • Fit the balconies into the slots in the wall assembly, as shown. Hint: The balconies are designed to fit one way. If a balcony does not seem to fit, turn it over and try again! • Push to "snap" each balcony in place. 12 • Fit the top ramp onto the assembly. • Insert three screws into the holes in
ページ8に含まれる内容の要旨
Spiral Speed Action! • Slide the cars down the ramps for spiral speed action! • Lower the sign for stop lights and fun sounds! • Lift and lower the gas hose for car sounds. • Slide the power switch on the bottom of the toy ON . P Power Switch ower Switch When you are finished playing with this toy, slide the power switch OFF . 8
