ページ1に含まれる内容の要旨
Model PRO 9644a
Owner’s Manual
3 Button Remote Security System with Starter Disable
IMPORTANT ! In order to provide the highest possible level of security to your vehicle, this
system is equipped with selectable manual override circuitry. It is possible that you will need to
manually override your security system if the transmitter becomes lost, or inoperative due to
battery failure. Reading the sections on "MANUALLY OVERRIDING YOUR SYSTEM" is
necessary to fully understand the procedure requi
ページ2に含まれる内容の要旨
YOUR " CODE HOPPING " TRANSMITTERS The transmitters included with your new security system use the most advanced and secure form of radio frequency transmission available on any current automotive security system. Some of today’s sophisticated auto thieves use a device known as a code grabber, which will receive and store the signal from your keychain transmitter, and re-transmit at a later time to disarm your system. Your anti code grabbing transmitters will change their signal every time the
ページ3に含まれる内容の要旨
Siren will not sound. If the siren "chirped" three times, sometime after arming, the exclusive delayed dome light learn circuit has been programmed and the system detected a open entry point after the learned delay expired. Closing the hood, trunk, or doors will correct the problem and you do not need to disarm the system to make the correction. Vehicles horn will not beep. If the horn beeps three times, then you have left a door, trunk, or hood lid ajar. Simply close the opened entry point
ページ4に含まれる内容の要旨
Whenever the system is triggered, the vehicle’s horn will beep for the full 30 second alarm cycle, attracting added attention to the vehicle. Optional - Whenever the system is triggered, the interior courtesy lights will flash for the full 30 second alarm cycle. Whenever the system is armed, the vehicle’s starting circuit will be bypassed. If the thief should choose to ignore the siren, the vehicle can not be started Optional - Any strong impact to the vehicle’s glass will cause the alar
ページ5に含まれる内容の要旨
SILENT DISARMING 1. As you approach the vehicle, press and hold the Unlock button on the keychain transmitter for 2 seconds. Red dash mounted LED turns off. If passive arming was selected during the installation, then the LED will start flashing rapidly, indicating that the system is re-arming automatically. Open any door to suspend the automatic arming. Parking Lights flash two times. If the parking lights flashed three times, then the alarm was triggered in your absence. Before turning the
ページ6に含まれる内容の要旨
If the LED is flashing one time...pause...one time...pause...etc., then an intrusion attempt was made to the OPTIONAL shock sensor, or an accessory triggering device that may have been added to the system. If the LED is flashing two times...pause...two times...pause...etc., then an intrusion attempt was made to a hood or trunk pin switch that was added to the system, or to a light activated entry point if the alarm was installed using the voltage sensing feature. If the LED is flashing thr
ページ7に含まれる内容の要旨
1. Disarm the system by use of the transmitter, or by use of the emergency override sequence. Turn the ignition switch to the on position. 2. Within 10 seconds, press and release the valet/override switch, 3 times. 3. Within 10 seconds turn the ignition switch off, on, off, on, off, on. (The siren or horn will beep and the lights will flash one time.) 4. Within 10 seconds, begin to enter your chosen 10ths digit by pressing and releasing the pushbutton switch from 1 up to 9 times. 5. Within 10 s
ページ8に含まれる内容の要旨
5 seconds during any of the above steps, the unit will revert back to the last successfully stored code. MANUALLY OVERRIDING YOUR SYSTEM: USING THE CUSTOM CODE OVERRIDE Assuming the override code programmed has not been changed, and the default override code of 11 is in the system's memory. 1. Enter the vehicle and turn the ignition switch to the on position. NOTE: The siren will sound. 2. Within 5 seconds, press and release the pushbutton switch 1 time. 3. Within 5 seconds, turn the ignition sw
ページ9に含まれる内容の要旨
allotted 30 seconds, however, the security system will be disarmed allowing the vehicle to start. OPTIONAL DEVICE OUTPUT (CHANNEL 3) Controlled By: Option Button, Both Lock & Unlock Button, Both Option & Lock Button, or Both Option and Unlock Button. This security system is equipped with an output which will activate when the appropriate transmitter button is depressed for four seconds. Optional devices that may be connected to this channel are: Remote Electric Trunk Release Remote Ca
ページ10に含まれる内容の要旨
PRO 9644 SYSTEM FUNCTIONS AT A GLANCE DASH LED INDICATORS RAPID FLASHING = PASSIVE ARMING SLOW FLASHING = ARMED OFF = DISARMED ON SOLID = VALET MODE 3 FLASH...PAUSE = INTRUSION ZONE 3 2 FLASH...PAUSE = INTRUSION ZONE 2 1 FLASH...PAUSE = INTRUSION ZONE 1 SIREN AND / OR HORN CHIRP INDICATORS 1 CHIRP * = ARM 2 CHIRPS * = DISARM 3 CHIRPS = ARM / DOOR OPENED 4 CHIRPS = DISARM / INTRUSION * These chirps are optional, and can be de - activated. PARKING LAMP INDICATORS 1 FLASH = ARM 2 FLASHES = DISARM 3
