ページ1に含まれる内容の要旨
1
128-8605
1 of 20
Model AS9233ST
Installation Manual
SELECTABLE FEATURES
The selectable features can be set manually as explained below, or with the RF feature programmer.
To set features using the RF programmer, follow the instructions packaged with the programmer.
Factory default settings are indicated by bold text.
Note : The method of manual override can either be selected to operate from the valet switch or operate as custom code.
Be certain to place a check mark indicating the method us
ページ2に含まれる内容の要旨
Note: Where indicated, press transmitter lock button to change, the Factory Transmitter Lock button, Door Lock Switch, or the supplied transmitter can be used. To program these selectable features; Action System Response Turn ignition on No response Press and release the valet switch 3 times 1 Chirp - LED 1 flash Within 3 seconds, turn ignition Off Then On Short chirp, then long chirp This Action Accesses Feature Bank 2 Alarm Selectable Features First Press and release the valet switch 1 time 1
ページ3に含まれる内容の要旨
3 128-8605 3 of 20 To exit program mode, turn ignition off, or press and release valet switch. RF Programmable Features Bank 3 Is Remote Start Selectable Features: Feature Selection 1 Chirp 2 Chirps 3 Chirps 4 Chirps 5 Chirps 6 Chirps 1st Defrost Output NA 2nd RF Start Chirp Off On On & Carfinder 3rd Run Time 5 Mins 10 Mins 15 Mins 20 Mins 45 Mins 60 Mins 4th Parking Lights On Steady Flashing 5th Input Check Voltage Tach DBI Tach Hybrid 6th Voltage Level >0.5V B4 Start < 0.5V B4 Start 7th Ign. 2
ページ4に含まれる内容の要旨
Action System Response Turn ignition on No response Press and release the valet switch 3 times 1 Chirp - LED 1 flash Within 3 seconds, turn ignition Off, On, Off, On Short chirp, then 2 long chirps This Action Accesses Feature Bank 3 Remote Start Selectable Features First Press the valet switch one time Non Functional On This Unit or Second Press and release the valet switch 2 chirps = RF start chirp on Press transmitter Lock button to change 1 chirp = RF start chirp off or Third Press and relea
ページ5に含まれる内容の要旨
This Remote Start/Alarm System is designed to be used with Automatic Transmission Vehicles Only! The unit provides a selectable ignition control that allows a number of selectable timed outputs for glow plug pre-heat which may be required for certain diesel vehicles, (see selectable feature #9). If the diesel engine has a instant fire, (no glow plug pre-heat system), feature #9 should remain in the default Gasoline mode setting. For diesel applications, consult your dealer for the type of igniti
ページ6に含まれる内容の要旨
from all areas of the vehicle. The selected location must be within 18" of the control module to allow routing and connecting of the 4 pin harness. Secure the shock sensor to the chosen location using two #8 self taping sheet metal screws. The sensor can also be secured to an existing dash brace using cable tie straps. Whichever mounting method is used be sure to allow access to the sensitivity adjustment potentiometer for use later in the installation. STARTER INHIBIT RELAY: Select a mounting l
ページ7に含まれる内容の要旨
Note: This wire must be connected to the vehicle side of the starter cut relay (when used). For the electrical neutral switch configuration, this connection must be made between the starter inhibit relay, (when used) and the neutral safety switch as shown in the following diagram. Failure to connect this wire to the ignition switch side of the neutral safety switch can result in personal injury and property damage. SEE NEUTRAL START SAFETY TEST FOR FURTHER DETAILS. YELLOW START WIRE DETAIL BLUE
ページ8に含まれる内容の要旨
WIRING CONNECTIONS: Multi Pin Accessory Input/Output Harness White w/ Red Trace Wire: Parking Light Flasher Feed This wire is the common contact of the on board parking light flasher relay. If the vehicle you are working on has +12 volt switched parking lights, connect this wire to a fused + 12 volt source. (Max. 15 Amps) Note: If the vehicle's parking lights are ground switched, connect this wire to chassis ground. White Wire: Parking Light Flasher Output This wire is the normally open contact
ページ9に含まれる内容の要旨
Dark Green Wire: (-) Instant Trigger Input This is the instant on ground trigger input wire. This wire must be connected to the hood and trunk pin switches where installed. Note: This wire will be shunted when remote control channel 3 is accessed, (trunk release). This wire will remain shunted all the while there is ground present and for 5 seconds after the ground is removed. This allows the operator to open the trunk via the remote transmitter without having to first disarm the alarm system. S
ページ10に含まれる内容の要旨
General Motors VATS By-Pass Diagram Grey Wire: Negative Inhibit Input The Grey w/ Black Trace wire provides an instant shutdown for the Remote Start Control Module whenever it is grounded. Connect the Grey trace wire to the hood pin switch previously installed. This wire must be routed through a grommet in the firewall and connected to the hood pin switch. If the factory switch is used, a diode assembly as shown below may be used to isolate the factory circuit from the this circuit. IMPORTANT!
ページ11に含まれる内容の要旨
Brown w/ Black Trace Wire: Positive Inhibit Input The Brown w/ Black Trace wire provides an instant shutdown for the Remote Start Control module when- ever it gets + 12 volts. If the Brake lights switch in the vehicle switches + 12 volts to the brake light circuit, connect the Brown w/ Black trace wire to the output side of the brake switch. This will allow the Remote Start to shut down if an attempt is made to operate the vehicle without the key while running under the control of the Remote St
ページ12に含まれる内容の要旨
Green/Yellow Wire: Diesel Wait To Start Input The Green/Yellow wire will connect to a diesel vehicles glow plug wire. When the unit receives a start command, this wire must go to + 12 then to ground to allow the crank sequence to begin. When ignition #1 is activated by the remote start unit, the glow plug circuit gets energized, (+ 12 volts), when the glow plug circuit of the vehicle drops the + 12 volts, which effectively grounds the wait to start input, then 500mS later the starter will enga
ページ13に含まれる内容の要旨
Note!When installing this system as a stand alone passive security system, the RED wire in this connector must be connected to a rest at ground , + 12 VDC switched ignition source. RED w/BLACK, GREEN & GREEN/BLACK wires must be connected to ground. The BLUE wire in this connector will not be required for the stand alone installation. The Trigger Input, feature # 18 must be set for delay instead of instant, to insure the consumer has time to get into the vehicle and turn the ignition on before
ページ14に含まれる内容の要旨
output would be to disarm a factory theft deterrent system to prevent false triggering of the factory alarm when the remote start unit engages or when the 785 is used to unlock the doors. Black w/ Light Green Trace Wire: Pulsed Ground Output After Start The Black w/ Light Green Trace wire will provide a 1 second mA pulsed ground output after the vehicle is started under control of the remote start unit. Typically this wire will be used to re-lock the vehicle doors if the doors unlock automatical
ページ15に含まれる内容の要旨
3 Wire Positive Switched Door Locks: In this application, the Red wire of the door lock harness provides a + 12 volt pulse during the disarming sequence, or pulsed 12 volt unlock output. Connect the Red wire to the low current 12 volt signal wire from the factory door unlock switch to the factory door unlock relay. The Green wire of the door lock harness provides a + 12 volt pulse during the arming sequence, or pulsed 12 volt lock output. Connect the Green wire to the low current 12 volt sign
ページ16に含まれる内容の要旨
To Learn Tach 1. Turn the ignition key to the On position. 2. Press and release the valet/program push button switch 3 times. 3. Immediately turn the ignition key Off. 4. Press and hold the valet/program push button switch, then start the vehicle using the key. 5. When the unit senses the tach signal, the parking lights will begin to flash. 6. Release the valet/program pushbutton switch. The parking lights will turn on for three seconds to indicate that the learned tach signal is stored and the
ページ17に含まれる内容の要旨
TESTING YOUR INSTALLATION: CAUTION!! The following procedure must be performed after the installation of an Audiovox Remote Start Device. It is the responsibility of the installing technician to complete these tests. Failure to test the unit in the following manner may result in personal injury, property damage, or both. HOOD PIN SAFETY SHUT DOWN: The intention of the hood pin safety shut down is to prevent the Remote Start unit from being activated while a mechanic or vehicle owner is performi
ページ18に含まれる内容の要旨
MECHANICAL NEUTRAL SAFETY SWITCH CONSIDERATIONS: Mechanical neutral safety switch configurations differ slightly in that they do not offer the same level of safety when installing a remote start device. Often when the ignition switch is turned off while the gear selector is in any position other than park or neutral, the mechanical function will not allow the key to be turned to the start position or be removed from the ignition cylinder. This configuration prevents mechanical operation while th
ページ19に含まれる内容の要旨
METHOD 2 To connect to the key in sensor circuit as shown for method 2: A. Locate the control wire that connects the drivers door pin switch to the key in sensor switch. B. Cut this wire and connect the ignition cylinder side to chassis ground. C. Locate the key in sensor switch wire that connects the chime module to the ignition cylinder. D. Cut this wire and connect the ignition cylinder side to the Remote Start Negative Safety Shut down Wire Gray/Black, using a 4002 series diode as shown abov
ページ20に含まれる内容の要旨
© 2009 Audiovox Electronics Corp., Hauppauge, N.Y. 11788 128-8605 20 128-8605 20 of 20
