ページ1に含まれる内容の要旨
Model AA-925
Installation Manual
Keyless Entry System
With Two Auxiliary Outputs
Installation Instructions
This Unit Is Intended For Installation In Vehicles With
12 Volt Negative Ground Electrical Systems Only.
Kit Contents:
(1) Control Module
(2) - Three Button Transmitters
4 Channel Code Learning Receiver
On Board Antenna
(1) - Multi Pin Input/Output Harness
(1) - Three Pin Door Lock Harness
(1) - Two Pin LED Indicator
(1) - Two Pin Valet / Override Switch
(1) - 15 Amp In-line Fuse
ページ2に含まれる内容の要旨
The AA-925 Keyless Entry System is designed to provide a convenient electronic means to gain access to the vehicle by providing RF remote control over the vehicle's power door lock system. The unit also includes outputs to control the vehicle's dome lights, as well as exterior parking lights. Although not an alarm system, this unit also incudes a starter interrupt circuit output. It also includes two additional auxiliary outputs designed to allow for control over optional devices such as a po
ページ3に含まれる内容の要旨
NOTE: Some vehicles, (mostly European) have isolated "left" and "right" side parking lights. To connect to the parking light systems in these vehicles, you must use separate SPDT relays to connect to each side in order to keep them isolated. Attach the WHITE wire of the system to this point. BROWN Wire: Negative (-) Door Sense Input Wire If the vehicle's interior lights are controlled by grounding door pin switches (typical of most GM, Chrysler, and import vehicles), the Brown negative door se
ページ4に含まれる内容の要旨
GREEN/BLACK Wire: Immediate, 300mA Duration of Transmit, Channel 3 Output The Green/Black wire supplies a 300mA switched output whenever Channel 3 of the receiver is accessed. Pressing A combination of the transmitter Lock/UnLock buttons simultaneously will access Channel 3 and will remain active for as long as the transmitter button(s) is held. This is a low current output and must be connected to a relay to supply power to the device you intend to control. Connect Green/Black Trace wire
ページ5に含まれる内容の要旨
The green wire provides a positive pulse during locking, or the pulsed + 12 volt lock output. Connect the green wire to the wire that provides a low current positive signal from the factory door lock switch to the factory door lock control relay. 3 Wire Positive Switched 2 Step Door Locks The green wire provides a positive pulse during locking, or the pulsed + 12 volt lock output. Connect the green wire to the wire that provides a low current positive signal from the factory door lock switch to
ページ6に含まれる内容の要旨
Programmable Features: Features 1 Chirp 2 Chirp 3 Chirps Default First Passive Arming Active Arming Active Arming Second Ignition D/L ON Ignition D/L OFF Ignition D/L OFF Third Ignition D/UL ON Ignition D/UL OFF Ignition D/UL OFF Fourth Chirps ON Chirps OFF Chirps ON Fifth Passive D/L Active D/L Active D/L Sixth Siren Output Horn Output Horn Output Seventh 800ms D/L Pulse 3.5 Sec. D/L Pulse 800ms D/L Pulse 800ms Door Lock Double 800ms D/UL Pulses To Program These Features: Entering the Programmi
ページ7に含まれる内容の要旨
Fourth Turn the valet switch on then off 1 chirp = chirps on 4 Flash pause Press transmitter Lock button to change 2 chirps = chirps off or Fifth Turn the valet switch on then off 2 chirps = active locks 5 Flash pause Press transmitter Lock button to change 1 chirp = passive locks or Sixth Turn the valet switch on then off 2 chirp = horn output 6 Flash pause Press transmitter Lock button to change 1 chirp = siren output or Seventh Turn the valet switch on then off 1 chirp = 800ms door lock outpu
ページ8に含まれる内容の要旨
© 2003 Audiovox Electronics Corp. 128-6711 128-6711 8 of 8
