ページ1に含まれる内容の要旨
FS-30
2-WAY REMOTE CONTROL ALARM SYSTEM
OPERATING INSTRUCTIONS
INTRODUCTION
CONGRATULATIONS on your choice of an Remote Alarm System by Crimestopper Security Products Inc.
This booklet contains the information necessary for installing, using, and maintaining your alarm system. If
any questions arise, contact your installation dealer or Crimestopper Security Products Inc. at the Tech
Support number below.
*IMPORTANT INFORMATION: Primary and Optional Features:
-PRIMARY: The
ページ2に含まれる内容の要旨
TABLE OF CONTENTS Operation Cautions & Warnings……..…………..……………………………………………………………………2 The Remote Controls………………………………...……………………..……………………….…….……..…..3-4 Quick Chart Button Functions…………………………....……………………………………………….…….........5 Operating Instructions………………………..……………….…….………………….…….…………...……....…6-9 Car Jack Protection..…………..…………..……………………………………………...…………………..…….…10 Transmitter Programming.………………………………….…………………………….……………...………..…11 2 Vehicle Programming…………..…………..………………….…
ページ3に含まれる内容の要旨
THE REMOTE CONTROLS 2-WAY - PAGER / REMOTE TRANSCEIVER: 1-WAY - SIDEKICK REMOTE: DISARM / UNLOCK AM ARM / TRUNK VEH 1 / VEH 2 12:00 PM LOCK SILENT SLT SILENT ARM / DISARM TRUNK VEH 1 / VEH 2 CLOCK SET DISARM / ARM / UNLOCK LOCK 3
ページ4に含まれる内容の要旨
THE REMOTE CONTROLS 1-WAY - SIDEKICK REMOTE: The 1-Way sidekick remote adds flexibility to your system. You can have the convenience of operating your system without needing to carry the larger pager remote. The Sidekick remote has less range and offers all of the same operation features except for page-back confirmation. The 1-Way Sidekick Remote uses two CR- 2016 Lithium 3 Volt Batteries. 2-WAY - PAGER / REMOTE TRANSCEIVER: The 2-Way hand-held remote transceiver is used to sen
ページ5に含まれる内容の要旨
QUICK CHART BUTTON FUNCTIONS Button Button Button Options Functions Lock Doors & Arm Press and hold 2 System Seconds for Panic Mode Unlock Doors and Unlock Doors and Disarm System Disarm System Press and Release for Trunk Release Aux # 1 Trunk Pop (Aux #1) Press and Release for Silent Arm / Disarm Aux Silent Arm. Press and SLT #2 Hold for Aux #2 Selects between Vehicle Press 5 times for Clock #1 / Vehicle #2. Press & VEH (AM / PM blinking) hold 2 Sec. Lock = Increase, Unloc
ページ6に含まれる内容の要旨
OPERATION INSTRUCTIONS ARMING To arm the alarm and lock the doors, press the Lock button on the transmitter. You will hear a single siren chirp and the lights will flash once. The system will arm, the doors will lock and the starter will be disabled if these optional features are installed. The red LED in the vehicle will start flashing after 5 seconds. After a short delay to allow vehicle and electronics to stabilize the system will be completely armed. DISARMING Press the Unlock
ページ7に含まれる内容の要旨
OPERATING INSTRUCTIONS ARM / DISARM WITH IGNITION ON (PROGRAM OPTION #15) This feature allows the system to be armed or disarmed while the ignition is in the ON position or vehicle is running. The feature is disabled by default and should not be used under normal operating conditions. On an installation with an add-on remote start module, this option can be enabled to allow the system to be armed or disarmed when the vehicle has been remote started (Ignition will be ON). Note that you
ページ8に含まれる内容の要旨
OPERATING INSTRUCTIONS EMERGENCY OVERRIDE / DISARM If you have lost the transmitter or it stops working for any reason and the Alarm is armed, you will have to open the door with the key, which will activate the alarm. Turn the ignition on and press the override/program button for about 5 seconds (until siren stops). The Alarm will disarm. If you continue to hold the button for additional 7 seconds, the system will enter the Valet mode. EMERGENCY DISARM WITH CUSTOM OVERRIDE Custom
ページ9に含まれる内容の要旨
OPERATING INSTRUCTIONS VALET MODE (Solid LED) To disable the Alarm system for vehicle service or otherwise, turn the ignition on and press the override/program button 4-5 seconds until the dash LED turns on solid and you hear (1) siren chirp. Repeat the process to exit VALET mode and the system will chirp (2) times and the LED will turn off. Lock/Unlock and AUX features will still operate in when in VALET mode. When performing an Emergency Override and you hold down the override butto
ページ10に含まれる内容の要旨
CARJACK PROTECTION ACTIVE CARJACK This feature provides Active Carjack protection and must be enabled before use through Alarm programming option (14) See page 10. When the Ignition is on (vehicle is running), press and hold button #3 (AUX) for 3 seconds. Parking lights will flash TWICE to confirm the Carjack countdown sequence. LED begins to flash slowly. 90 Seconds later, the unit will begin a Carjack Cycle consisting of 20 seconds of pre-warning chirps turning into a full system ac
ページ11に含まれる内容の要旨
TRANSMITTER PROGRAMMING NOTE: All transmitters must be learned at the time of programming. This system can learn up to 4 remotes. 1. Turn key to the ON position and press program button 4 times. 2. After a short delay, the unit will flash the parking lights 4 times, Siren 4 times, Horn 4 times and status LED will be on solid. 3. Press the Lock Button on the remote you wish to program. 4. You should get 2 light flashes, 2 siren chirps and 2 horn honks (optional) indicating the unit is
ページ12に含まれる内容の要旨
2 VEHICLE OPERATION / PROGRAMMING 2 VEHICLE CONTROL Your remotes have the ability to control a second vehicle with a Crimestopper system installed. To set up the 2-Vehicle operation you must first program your remotes to Vehicle #2. Follow the “Transmitter Programming” steps (Pg. 11) at the second vehicle and learn YOUR remote, along with vehicle #2’s existing remotes. 2-VEHCLE NOTES: (1) You do not have to switch between Vehicle “1” and “2” to get pages from each vehicle. Your re
ページ13に含まれる内容の要旨
BATTERY REPLACEMENT LOW BATTERY WARNING The 2-Way LCD remote has a low battery warning system. When the battery voltage is low, the LCD Pager Remote will show a low voltage icon. We recommend replacing the battery for proper operation. To replace the battery: Simply unlatch and slide open the battery door on the back of the remote. Carefully insert a new 1½ Volt AAA Battery using the outline on the bottom of the battery compartment as a guide. Your remote will beep 3 times & vib
ページ14に含まれる内容の要旨
2-Way DATA PORT Some vehicles require a Databus Module to Bypass the factory Immobilizer and operate the keyless entry Databus modules are used to communicate with the vehicles computer at the OBD2 Data connector or Canbus wires. This reduces installation error. Crimestopper Systems with DP Series have a direct Data Port Plug-In for the Databus bypass module. This eliminates conventional wiring between the Alarm/Remote Starter and the bypass interface module. Features Include • Tran
