ページ1に含まれる内容の要旨
EZ-30 / EZ-10
REMOTE ENGINE STARTING SYSTEM
OPERATING INSTRUCTIONS
INTRODUCTION
**IMPORTANT NOTES:- FOR EZ-10 MODEL ONLY**
The EZ-10 Model is for remote starting purposes only. It has NO keyless entry functions. Any information in this
manual pertaining to remote keyless entry functions, door lock & door unlock applies only to the EZ-30 model.
*IMPORTANT INFORMATION: Primary and Optional Features
-PRIMARY: These are features that must be connected in orde
ページ2に含まれる内容の要旨
TABLE OF CONTENTS Operation Cautions & Warnings…….……………..….…………………………………….…………………………2 Remote Control Diagrams………...……………………………………………………………………………...…….3 Remote Engine Control…………….…..…………………………………………………………………….……….4-6 Turbo Timer Mode……………………………….……………………………………...………………………………7 Convenience and Safety Features……………………………….……………………………………...……..……8-9 Transmitter Programming….…………….…………………………………………….……………………...……..9-10 2 Vehicle Operation.…………………………………….………………...……………………..…………….……
ページ3に含まれる内容の要旨
REMOTE CONTROL DIAGRAMS EZ-30 EZ-10 System #2 Flashlight UNLOCK #1 FLASHLIGHT Vehicle LOCK #2 VEHICLE #2 Engine #3 Start/ ENGINE Stop START/STOP EZ-30 SYSTEM The transmitter supplied with the EZ-30 system has 5 buttons total. The button configuration of the EZ-30 is Factory-set and unchangeable. See Page 11 for additional information on how to use your remote to operate a second vehicle equipped with an EZ-30 or EZ-10 system. EZ-10 SYSTEM The transmitter supplied with the EZ-10 sys
ページ4に含まれる内容の要旨
REMOTE ENGINE CONTROL REMOTE ENGINE STARTING - SUCCESSFUL START: 1) Press the remote start button for at least 1 second. 2) Parking lights flash once; return solid, and the Ignition/Acc circuits turn on. 3) After a few seconds the Starter Motor engages, Parking lights and Acc circuits will turn off while cranking. 4) Engine Starts and Runs. Parking Lights and Acc turn back on, Doors Lock. 5) Engine will remain running for programmed run time until it is reset with Brake pedal. SOLID
ページ5に含まれる内容の要旨
REMOTE ENGINE CONTROL ENTERING YOUR REMOTE STARTED VEHICLE: 1) With engine running, Remote Unlock system (EZ-30) or open door with key. 2) Enter vehicle and be careful not to step on brake pedal! (Remote Start Reset) 3) Turn Ignition to ON/RUN position, then press brake pedal to reset the Remote Starter & Shift out of park. 4) Remote starter will reset instantly when the brake is pressed. Parking lights will turn off and the ignition key is now controlling your vehicle. ID
ページ6に含まれる内容の要旨
REMOTE ENGINE CONTROL INFINITY RUN MODE This mode can only be activated when "Idle Down" procedure. The Infinity Run mode allows the vehicle engine to remain running INDEFINITELY after the programmed run time elapses. This mode will allow the vehicle to be left running and unattended without the ignition key in the switch preventing the vehicle from being stolen. This mode can be beneficial to law enforcement or commercial trucks that need to remain running unattended for long perio
ページ7に含まれる内容の要旨
TURBO TIMER MODE (OPTIONAL) The optional Turbo Timer mode allows the EZEE Start system to keep a Turbo or Turbo Diesel vehicle running for 1 to 5 minutes [selectively] after you remove the key, exit the vehicle, and lock the doors remotely. This is handy for turbo cool-down without the need for expensive turbo timers. This mode requires the use of an extra part called a momentary switch/button that is not included with the kit. Check with your installer about adding this feature. NO
ページ8に含まれる内容の要旨
CONVENIENCE AND SAFETY FEATURES EZ-30 ONLY: KEYLESS ENTRY (POWER DOOR LOCK CONTROL, Optional) This system enables you to remotely lock and unlock the vehicle’s doors (if equipped with power locks) via remote control for safety and convenience. Note: This feature may require extra labor and/or parts to install. Press the Lock or Unlock transmitter button as you leave or come near the vehicle. Parking lights will flash once for lock and twice for unlock. If vehicle is running by the r
ページ9に含まれる内容の要旨
CONVENIENCE AND SAFETY FEATURES BRAKE PEDAL RESET Prevents starting or shuts off a remote started vehicle when this circuit is active or activated. Prevents unauthorized tampering. This circuit shuts the system down immediately when brake pedal is pressed if the key is not in ignition and turned to the ON position. OEM ALARM INTERFACE This feature is designed to Disarm and Re-arm Factory equipped security systems in conjunction with remote start and keyless entry (if needed fo
ページ10に含まれる内容の要旨
TRANSMITTER PROGRAMMING TRANSMITTER PROGRAM DIAGRAM: IGN OFF WAIT FOR (GRAY WIRE GROUNDED) 4 FLASHES PRESS 4X's EZ-30 EZ-10 IGN OFF FLASH 2, 3, or 4 X's COMPLETE PRESS PRESS LOCK BUTTON START BUTTON 10
ページ11に含まれる内容の要旨
2-VEHICLE OPERATION The EZ-30/10 systems can be used for 2 vehicle operation. A single remote can control a second vehicle with an VEHICLE #2 identical system installed. There are some exceptions. See “Multi-Vehicle Notes” section below. Press lower side button Pressing the lower side button on your remote transmitter first, then you have switches your remote to car #2 mode for 3-seconds. You can continue operating Vehicle#2 functions within this 3- 4 seconds to second window as
ページ12に含まれる内容の要旨
TROUBLESHOOTING: “BEFORE YOU CALL” SECTION UNIT FLASHES LIGHTS ONCE AND WILL NOT ATTEMPT A START: The unit senses a fault at the Brake (Purple wire is active) or the Hood is OPEN (Gray wire grounded). This is a safety feature of the unit. Check installation for faults and make sure hood is closed and latched and brake wire is not active. UNIT CRANKS VEHICLE BUT ENGINE NEVER STARTS: • In some vehicles, there may be a Factory anti-theft system that will not allow the engine to run withou
