ページ1に含まれる内容の要旨
Remote Vehicle Control System
CA 650
Owner's Manual
Vehicle Security and Remote Start
System with Two Way Confirming
LCD Remote Control
IMPORTANT NOTE: The operation of the Security and Convenience System as described in this manual is
applicable to most vehicles. However, due to the configuration of some vehicles, some functions AND/OR SAFETY
PRECAUTIONS may not apply. Please see your installing dealer for more information.
ページ2に含まれる内容の要旨
Table of Contents Using Your Remote Control .......................................................... 3 Arming the security system Passive Arming Hidden alarm function Disarming the security system Two stage door unlock* Automatic rearm Valet mode Using Your Remote Control, continued .................................... 4 Activating trunk release* Activating optional AUX 1* Using the car finder feature Using the personal protection alarm 2-car mode Anti-car jacking mode Using Your Remote Vehicl
ページ3に含まれる内容の要旨
Using Your Remote Control Arming the Security System To arm the system, exit the vehicle, close all doors, then press the LOCK icon button on the remote control. The system will sound once and the parking lights will flash once, indicating the system is armed. The doors will also lock at this time (if equipped and connected). The status indicator (red warning light on the dash) will blink steadily, once per second. To arm the system silently, press the LOCK and UNLOCK icon buttons for 1 sec
ページ4に含まれる内容の要旨
Using Your Remote Control, continued Activating the Trunk Release Feature (Optional) If this feature is enabled on your system, pressing and holding the TRUNK icon button on the remote control for 2 seconds will open the vehicle’s trunk or hatch. Activating Optional AUX 1 (Optional) If this feature is enabled on your system, pressing the LOCK and TRUNK icon buttons on the remote control simultaneously will activate an optional feature. This feature can be programmed for a wide range of func
ページ5に含まれる内容の要旨
Using Your Remote Vehicle Starter Remote Starting Your Vehicle To activate the remote vehicle start function, press and release the STAR button on the remote control two (2) times within 2 seconds. The system will sound, the parking lights will flash 1 time and the system will check the vehicle to ensure it is safe to start. If all safety parameters are correct, the vehicle will start within 5 seconds. The vehicle’s parking lights will turn on (or flash depending on system settings) as a vis
ページ6に含まれる内容の要旨
Using Your Remote Vehicle Starter, continued Operating the 2 / 3 Hour Start Up Timer Mode The system has the ability to start the vehicle every 2 or 3 hours with a MAXIMUM of 6 start cycles. This feature is especially useful in cold climates where the only means to keep the engine and engine fluids warm is to periodically start the engine. WARNING! Be certain that the vehicle is outdoors before using this or any remote starting device. A running engine produces dangerous carbon monoxide fume
ページ7に含まれる内容の要旨
Additional 2-Way LCD Remote Control Functions Check Vehicle Status Press and release the TRUNK button and then simultaniously press the LOCK and UNLOCK buttons, the transmitter will respond with one melody sound and display the current status of the vehicle. LCD Remote Control Display Illumination Press and release the TRUNK button on the LCD remote control one time. The display will illuminate for 5 seconds. LCD Remote Control Vibrate or Tones First enter TRANSMITTER FUNCTION MODE by
ページ8に含まれる内容の要旨
LCD Remote Control ICON’s UNLOCK LOCK VALET MODE ARM SYSTEM ARMED TRANSMITTING IN-RANGE INDICATOR HOOD/TRUNK TRIGGER DOOR TRIGGER WARN AWAY TRIGGER FULL SHOCK TRIGGER ENGINE RUNNING IGNITION ON/TRIGGER IGN TIME CONTROL START 2 CAR MODE BATTERY INDICATOR SAVE BATTERY SAVE MODE PAGE FROM VEHICLE VIBRATE/SILENT MODE 8
ページ9に含まれる内容の要旨
LED and Siren/Horn Indications LED Display Indications LED Function OFF DISARMED SLOW FLASH ARMED FAST FLASH PASSIVE ARMING ON (SOLID) VALET MODE 2 FLASH... PAUSE ZONE 2 TRIGGER, HOOD/TRUNK 3 FLASH... PAUSE ZONE 3 TRIGGER, DOOR 4 FLASH... PAUSE ZONE 4 TRIGGER, SHOCK 5 FLASH... PAUSE ZONE 5 TRIGGER, IGNITION Siren/Horn Indications Chirps Function 1 ARM 2 DISARM 3 DOOR AJAR UPON ARMING 4 DISARM / TRIGGERED 6 CAR LOCATOR Parking Light Flash Indications Flashes Function 1 ARM 2 DISARM 3 DISARM
ページ10に含まれる内容の要旨
Replacing Remote Control Batteries 2-way LCD Remote Control: The AAA alkaline battery inside the 2-way LCD remote control should last approximately 1 year under normal use. When the batteries become weak you will notice the remote control range (the distance from the vehicle the remote control will work) deteriorate and the BATTERY icon on the LCD remote control will show. 1. Slide the small release tab on the back of the remote control to the unlock position. 2. Gently slide the battery cove
ページ11に含まれる内容の要旨
Emergency Override Procedure If your transmitter is lost or disabled, it will be necessary use the emergency override button to turn the security system off. There are two types of emergency override procedures. Check with your installing dealer to find out what has been activated on your system. Standard Emergency Override Procedure 1. Enter the vehicle, the security system will trigger. 2. Turn the ignition key to the ON position. 3. Press and release the emergency override button. The
ページ12に含まれる内容の要旨
Code Systems, Inc. Limited Lifetime Warranty Code Systems Inc. (“CODE”) warrants to the ORIGINAL PURCHASER of this CODE vehicle security product (the “Product”), purchased from an authorized CODE dealer, that (except as provided below) should this Product under normal use and conditions, be proven defective in material or workmanship DURING THE LIFETIME OF THE VEHICLE IN WHICH IT WAS ORIGINALLY INSTALLED, such defect(s) will be repaired or replaced (at CODE’s option) without charge for parts dir
ページ13に含まれる内容の要旨
FCC COMPLIANCE This device complies with Part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including any interference that may cause undesired operation. Warning! Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
