ページ1に含まれる内容の要旨
Model APS-2K4, APS-2K4S,
APS-2K4MS, APS-2K4SFL
& APS-2K4MSFL
Transmitter Programming Guide
These transmitters makes use of icons (symbols) to identify the reac-
tion your security system/keyless entry/and or remote start system,
where applicable, will have when any icon (button) is pressed.
These icons are programmed at time of installation to meet the needs of
the individual and to complement the vehicle that the system is installed
in. To replace a transmitter or add transmitters, please foll
ページ2に含まれる内容の要旨
Some of the more popular options available for the unused Option Buttons of your transmitter are: AS 9554 Remote Garage Door Interface (APS-2K4S only) AS 9075 Remote car starter AS 9153 Remote window roll up AS 9256 Remote trunk release relay Although the most common use of the transmitter buttons are shown on the front page of this guide, any button or button combination can be programmed into any receiver channel. Additionally, if all 4 buttons are used and you require access to a 5th channe
ページ3に含まれる内容の要旨
NOTE: If your transmitter button has the Lock/Unlock icon on one button, press and release the valet push button switch 2 times then move on to step #8. 5) Press and release the valet push button switch one time to advance to channel 2. The siren will chirp 2 times and the dash mounted LED will Flash 2 times, indicating that the unit is ready to accept program- ming for channel # 2 which is only used for separate lock and unlock button transmitters, and is the disarm/unlock/unlock 2 and panic.
ページ4に含まれる内容の要旨
three times. (Siren emits 1 short chirp indicating channel 1 has been entered) 3. Within 10 Seconds, press and hold the ARM or ARM/DISARM button of the first transmitter you wish to remain stored into the control unit until a single chirp is heard from the siren. (Repeat this for each transmitter you wish to remain stored in the control unit). The receiver stores up to four transmitters. To be certain all transmitter slots in the receiver are occupied with transmitters you wish to con- tinue t
ページ5に含まれる内容の要旨
The light will turn off when the button is released. Caution! Always point the light away from you and the eyes of others. This is a bright high intensity LED which should not be directed toward or into the eyes of anyone. QUICK REFERENCE CHART: You can program any individual channel without reprogramming all channels. To go directly to a particular receiver channel follow the chart below: CHANNEL VALET SWITCH LED 1 Ign. On Then Press and Release 3 Times 1 Flash 2 Ign. On Then Press and Release
ページ6に含まれる内容の要旨
ORDER FORM FOR APS-2K4, APS-2K4S, APS-2K4MS, APS-2K4SFL & APS-2K4MSFL Attention: Transmitter Ordering De- partment Important: To help us expedite your or- der, please print all of the information legibly and mail this form and your payment according to the instructions below. Indicate the pad number of your trans- mitter selected from the pads shown above. Note: Transmitter model number found on back of case. APS-2K4MSFL & APS-2K4SFL Main use PD 110, Side use 111 1)Pad Number:_________________
ページ7に含まれる内容の要旨
THIS PAGE LEFT BLANK INTENTIONALLY 7 128-6516A 7 of 8
ページ8に含まれる内容の要旨
© 2006 Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, NY, 11788 128-6516A 8 128-6516A 8 of 8