ページ1に含まれる内容の要旨
Model APS-520
Owner’s Manual
ARMING THE SYSTEM - ACTIVE
1. Turn off the engine, exit the vehicle, and close all doors, hood lid
and trunk lid.
2. Press and release Lock/Arm button on the keychain transmitter.
The dash mounted LED begins to flash slowly. Parking Lights flash
one time.
Siren sounds one chirp.
If the siren/horn sounds 3 chirps, then you have left a door, trunk,
or hood lid ajar. Simply close the opened entry point to provide full
protection. If the siren "chirped" three times, s
ページ2に含まれる内容の要旨
intrusion attempt has occurred, the siren will chirp 4 times and the parking lights will flash 3 times when disarming the system. Enter the vehicle and observe the red dash mounted LED to identify which zone was triggered. 1. If the LED is flashing one time...pause...one time...pause...etc., then an intrusion attempt was made to the shock sensor, or an accessory triggering device that may have been added to the system. 2. If the LED is flashing two times...pause...two times...pause...etc., then
ページ3に含まれる内容の要旨
2. Turn the ignition switch to the on position. 3. Within 10 seconds, press and release the valet/override switch, 3 times. 4. Within 10 seconds turn the ignition switch off, on, off, on, off, on. (The siren or horn will beep and the lights will flash one time.) 5. Within 10 seconds, begin to press and release the pushbutton switch to set the tenths digit. (As per the example, press and release 5 times to set the tenths digit to 5) 6. Within 10 seconds of the last press of the pushbutton, turn t
ページ4に含まれる内容の要旨
that can be selected by the operator: 1. Normal Operation (default mode) In this mode, any strong vibrations will cause the siren to sound (full detect) for 30 seconds. Any lesser vibration will cause the siren to emit about 6 short warn away chirps, (pre-detect). 2. Stage 1 (Omit pre-detect) In this mode, the warn away chirps created by the lesser vibration will be deleted. If strong vibration occurs, the siren will sound. 3. Stage 2 (Omit pre & full detect) In this mode, both the pre-detect
ページ5に含まれる内容の要旨
2) Press and release the pushbutton switch three times The unit will flash the parking lights and or beep the horn once to indicate that the system is in the transmitter program mode. The LED will also flash one time pause, one time pause, etc... indicating that you are in the transmitter program mode of the unit’s channel 1 or single button program mode. 3) Press and hold any combination of buttons of your transmitter that was not used for your primary vehicle. If, for instance you can press &
ページ6に含まれる内容の要旨
FEATURES AND FUNCTIONS OF YOUR TWO WAY LCD 920TX2 Doors are locked Icon. If the system is armed “ ARM “ will also appear below the Lock Icon. Doors Unlocked Icon. Valet Mode. When Transmitting, any button activated. Within Range Indicator. Timed Start Activated. Someone Paging You From Your Vehicle. Vibrate Mode Is On. Toggle feature on and off by pressing Trunk/Key + * buttons for 5 seconds until beep is heard, then press the Unlock Button Once. Battery Save Mode Is On. Battery Level Indica
ページ7に含まれる内容の要旨
ORDER FORM FOR 620TX & 920TX2 Attention: Transmitter Ordering Department Important: To help us expedite your order, please print all of the information legibly and mail this form and your payment ac- cording to the instructions below. Note: Transmitter model number found on back of case. 620TX 920TX2 1) Transmitter Model Number_____________________ 2) Name: _______________________________________ 3) Address: ______________________________________ 4) City: ________________ State: _____ Zip Co
ページ8に含まれる内容の要旨
© 2007 Audiovox Electornics Corporation, 150 Marcus Blvd., Hauppauge, N.Y., 11788 128-8146 Page 8 128-8146 8 of 8