ページ1に含まれる内容の要旨
Model PRO-9775
Owner's Manual
4 Button Remote Start Security System With
Plug-In Shock Sensor & Starter Disable
FEATURES:
2 Four Button Programmable RF Transmitters
Four Channel Code Learning Receiver (capable of accepting 4 transmitters)
Code Hopping Technology
Selectable Manual Override Mode
Remote Panic in all modes
Protected Valet/Override
Remote Start Safety Control Switch
Selectable Automatic Timed Start Mode
User Programmable Manual Override Code
7 Function LED - Arm /
ページ2に含まれる内容の要旨
Your Remote Start Alarm System has many features and available options some of which are selected at time of installation. For your reference, the list on page 9 of this manual shows what features and options have been installed. Consult your installing dealer for options that may have been installed and are not listed. YOUR “ CODE HOPPING “ TRANSMITTERS: The transmitters included with your new remote start system use the most advanced and secure form of radio frequency transmission available o
ページ3に含まれる内容の要旨
ARMING THE SYSTEM - PASSIVE (AUTOMATIC) If the passive arming feature has been selected: 1. Turn the engine off, exit the vehicle, and close all doors, hood and trunk. The dash mounted LED will begin to flash rapidly indicating that the 30 second passive arming timer has begun. If the LED does not begin to flash rapidly, then you have left a door, hood, or trunk ajar. Closing this entry point will allow the arming cycle will begin. If any entry point is opened during the 30 second arming cycle,
ページ4に含まれる内容の要旨
NOTE: If the optional 2 step door unlock circuit is installed, when the unlock transmitter button is activated, the drivers door only will unlock, pressing the unlock button a second time will cause all doors to unlock. If your transmitter has a sperate lock unlock buttons, pressing the unlock button anytime after the first unlock command will cause all the vehicle doors to unlock. SILENT DISARMING 1. As you approach the vehicle, press and hold the disarm button of your key chain transmitter fo
ページ5に含まれる内容の要旨
either by using your keychain transmitter, or by activating your personalized manual override code. 1. Enter the vehicle, and turn the ignition key to the on position. 2. Press and hold the valet pushbutton switch until the dash mounted LED turns on solid. The system will remain in the valet mode. 3. To return to normal operation, press and release the pushbutton switch any time the ignition is on. NOTE: Always remember to return the vehicle to the valet off position. This will ensure that the v
ページ6に含まれる内容の要旨
NOTE: If 15 seconds of inactivity expire, or if the ignition switch is turned off for more then 5 seconds during any of the above steps, the unit will revert back to the last successfully stored code. Custom Code Programming Example: To Change the code from the factory pre-assigned code of 11 to “52” you would do the following: 1. Disarm the system by use of the transmitter, or by use of the emergency override sequence. 2. Turn the ignition switch to the on position. 3. Within 10 seconds, press
ページ7に含まれる内容の要旨
4. If the chirps were on before you started, the siren will emit 2 short chirps indicating that the chirps are now off. If the chirps were off before you started, the siren will emit one short chirp indicating that the chirps are now on. NOTE: If the vehicle battery is disconnected then reconnected, the unit will return to the default setting of chirps on. Repeat the above procedure to eliminate the arm/disarm chirps. REMOTE PANIC OPERATION The Lock or Unlock button on your keychain transmitte
ページ8に含まれる内容の要旨
minutes. As a visual indication, the parking lights will flash or turn on depending on the programming set up by your installation center. When you arrive at your vehicle, disarm the alarm system by pressing and releasing the Disarm button of your keychain transmitter. Enter the vehicle and turn the ignition key to the on position. CAUTION ! Do not turn the key to the start position. This will cause the starter motor to engage with the already running engine which could result in damage. Step
ページ9に含まれる内容の要旨
ADDITIONAL REMOTE FUNCTION CHANNEL 3 The system has an additional feature, (Channel 3) ,that can be connected to a number of different optional accessories. Some of the more common uses for this channel are: Remote Trunk Release Remote Window Close Remote Garage Door Interface To operate the accessory associated with channel 3, press and hold the trunk/key button(s) of your keychain transmitter for four seconds. NOTE: The feature that has been added to channel 3 will always be operated u
ページ10に含まれる内容の要旨
PRO-9775 SYSTEM FUNCTIONS AT A GLANCE ALARM DASH LED INDICATORS RAPID FLASHING = PASSIVE ARMING SLOW FLASHING = ARMED OFF = DISARMED ON SOLID = VALET MODE 3 FLASH... PAUSE = INTRUSION ZONE 3 2 FLASH...PAUSE = INTRUSION ZONE 2 1 FLASH...PAUSE = INTRUSION ZONE 1 ALARM SIREN CHIRP INDICATION 1 CHIRP* = ARM 2 CHIRPS* = DISARMED 3 CHIRPS = ARMING WITH ENTRY POINT OPENED 4 CHIRPS = DISARM AFTER INTRUSION 5 CONTINUOUS = TRIGGERED/PANIC ALARM PARKING LAMP INDICATIONS 1 FLASH = ARM 2 FLASH = DISARM 3 FLA
