ページ1に含まれる内容の要旨
Model PRO 9842B
Installation Manual
Vehicle Alarm System
With Auxiliary Output
Installation Instructions
This Unit Is Intended For Installation In Vehicles With
12 Volt Negative Ground Electrical Systems Only
Kit Contents:
(1) Control Module
(2) - Three Button Transmitters
3 Channel Code Learning Receiver
(1) - Multi Pin Input/Output Harness
(1) - Two Pin Door Lock Harness
(1) - Two Pin LED Indicator
(1) - Two Pin Valet / Programming Switch
Multi-tone Siren
(1) - Installation Manual
(1) - Operat
ページ2に含まれる内容の要旨
The PRO 9842B Vehicle Alarm System is designed to provide a basic deterrent to vehicle theft, and a convenient electronic means to gain access to the vehicle by providing RF remote control over the vehicle's power door lock system. The unit also includes outputs to control the vehicle's parking lights and an additional auxiliary output designed to allow for control over an optional device such as a power trunk release or engine starting device. BEFORE BEGINNING THE INSTALLATION: 1) Find location
ページ3に含まれる内容の要旨
HOOD AND TRUNK PIN SWITCHES: The pin switch included in this package is intended for protecting the hood or trunk/hatch areas of the vehicle. In all cases, the switch must be mounted to a grounded metal surface. When the pin switch is activated, (hood/trunk open), it will supply a ground to the input wire thus activating the alarm. Mount the switches in the hood or trunk locations away from water drain paths. If necessary, the included bracket may be used to move the switch away from rain gut
ページ4に含まれる内容の要旨
cases the factory door pin-switches are wired in parallel, making it necessary to connect to only one door switch in order to detect the opening of all doors. In a few cases this will not be true, making it necessary to connect to the vehicle dome light, or isolated door trigger wires. Locate the vehicle's positive door trigger wire in the vehicle's kick panel or under-dash. Splice and tape the PURPLE wire of the system to this point. DARK GREEN Wire: Negative (-) Hood/Trunk Trigger Input Wire T
ページ5に含まれる内容の要旨
+12VDC source. Connect the common, normally open, and normally closed contacts of the relay to perform the selected function of Channel 3. DOOR LOCK/UNLOCK CONTROL HARNESS (+) and (-) 2-PIN White Plug w/2 Wires; RED & GREEN The Red and Green Door Lock/Unlock output wires provide either a momentary pulsed ground (-) or a momentary pulsed 12VDC (+) output for controlling a vehicle's power door lock/unlock circuit. In order to accomplish this "dual polarity" output scheme these two wires produce t
ページ6に含まれる内容の要旨
OPTIONAL SHOCK SENSOR 4-PIN White Plug w/4 Wires; Red, Black, Blue, and Green The Red (+12 volt), Black (ground), Blue (pre-detect) and Green (full trigger when armed) wires loaded into the white connector shell are the inputs/outputs of the shock sensor. Route the 4 wire harness from the shock sensor location to the Control Module and plug the 4-PIN white connector into the mating 4-PIN connector. VALET/PROGRAM/MANUAL OVERRIDE SWITCH 2-PIN Blue Plug w/2 Wires; Black and Gray The Black and Gray
ページ7に含まれる内容の要旨
once you have toggled past it. Should you accidentally toggle past the feature you wanted to program, you must exit and re-enter the Programming Mode and then adjust the feature you missed. It is also important to note that you may toggle past as many programmable features as you wish without having to adjust them. Each time you toggle forward to a new feature, the siren will chirp the appropriate number of times (1 or 2 times) to indicate how that feature is currently set, and the LED will flas
ページ8に含まれる内容の要旨
© 2003 Audiovox Electronics Corp. 128-6189C 8
