ページ1に含まれる内容の要旨
Please read this manual and save it Please read this manual and save it
with your original sales receipt. with your original sales receipt.
T Tools needed for assembly: Phillips screwdriver ools needed for assembly: Phillips screwdriver
(not included) and Assembly Wrenches (included). (not included) and Assembly Wrenches (included).
® ®
Use only with a Power Wheels Use only with a Power Wheels 6 V 6 Volt olt
Rechargeable Batter Rechargeable Battery with A-Style Connector y with A-Style Conn
ページ2に含まれる内容の要旨
TABLE OF CONTENTS TABLE OF CONTENTS Important Information ............................................................... ........................2 Parts ............................................................... .....................................4 Parts Picture ............................................................... ...............................7 Batter y Charging ............................................................... ............................8 Assembly .......
ページ3に含まれる内容の要旨
IMPORTANT INFORMATION ELECTRICAL HAZARD DANGER To pr e v ent electr ic shoc k, do not immer se in w at er ; wipe clean with a damp cloth. WARNING • Bat t er y can f all out and injur e a child if v ehicle tips over. Alwa ys use the bat t er y r et ainer . • PREVENT FIRE - Ne v er modify the electr ical system. Alt er ations could cause a fire r esulting in ser ious injur y and could also r uin the electr ical system. - Use of the
ページ4に含まれる内容の要旨
PARTS • If you experience a problem with this product, or are missing a part, please call us at 1-800-348-0751 , rather than return this product to the store. • Please identify all parts before assembly and save all packaging material until assembly is complete to ensure that no parts are discarded. • Metal parts have been coated with a lubricant to protect them during shipment.
ページ5に含まれる内容の要旨
PARTS Steering Column Steering Wheel Cover 2 Side Mirrors 4 Wheels 4 Hubcaps Steering Wheel 4 Hubcap Covers Rear Axle 2 Rear Wheel Drivers 2 Side Windows K3033pr-0921 5
ページ6に含まれる内容の要旨
PARTS 2 Bushings 3 /8" -16 Hex Nut - 5 Key 7 /16" Washer - 2 Wrench - 2 3 #8 x /4" Screw - 11 1" Bolt - 2 6 Volt Battery 1 #12-32 x 1 /4" Screw - 2 For your convenience, we included extra fasteners! Note: T ighten and loosen all screws with a Phillips screwdriver . Do not over -tighten the screws. Super 6 Volt Charger Part not shown: Label Sheet - 2 Fasteners Shown Actual Size K3033pr-0921 6
ページ7に含まれる内容の要旨
PARTS PICTURE Note: Some parts shown are assembled on both sides of the vehicle. 2 14 4 22 3 15 13 21 1 18 19 5 12 17 6 22 10 16 23 11 7 9 12 22 8 10 11 20 Parts Not Shown 1 V ehicle 9 Bushing - 2 17 Side Window - 2 2 Seat 10 Wheel - 4 18 Rear Axle 3 #8 x / " Screws - 11 Assembly Wrench 4 3 Hood 11 Hubcap - 4 19 Rear Wheel Driver - 2 1 " Bolt - 2 Label Sheet - 2 4 Windshield 12 Hubcap Cover - 4 20 Super 6 V olt Charger 1 #12 x 1 / " S
ページ8に含まれる内容の要旨
BATTERY CHARGING ELECTRICAL HAZARD CAUTION WARNING • Bat t er y can f all out and injur e a child if Use the char ger in dr y locations onl y . v ehicle tips over. Alwa ys use the bat t er y r et ainer . About Thermal Fuses • PREVENT FIRE ® Y our Power Wheels 6 volt batter y is equipped with a built-in - Ne v er modify the electr ical system. thermal fuse. The thermal fuse is a self-resetting safety device Alt er ations could cause a
ページ9に含まれる内容の要旨
BATTERY CHARGING ASSEMBLY WARNING Power Childr en can be har med b y small par ts , Indicator shar p edges and shar p points in the v ehicle's unassemb led st at e , or b y electr ical it ems . C ar e should be t ak en in unpac king and assemb l y of the v ehicle . Childr en should B not handle par ts , including the bat t er y , or help in assemb l y of the v ehicle . CAUTION A In the unassemb led st at e , this pac k age cont ains Battery Charg
ページ10に含まれる内容の要旨
ASSEMBLY Motors Seat Vehicle Hole in Motor Rear Axle Assembly 3 FRONT VIEW • Rotate the seat back and lift to remove from the vehicle. 5 • Slide the rear axle assembly through the hole in one motor , the Motors back end of the vehicle and then out through the other motor . Rear Wheel Driver (Ring Side Out) Rear Axle Wheel (Rib Side In) 4 TOP VIEW Motor Hubcap • Locate the motors inside the vehicle. (Peg Side In) • Make sure each motor is positioned
ページ11に含まれる内容の要旨
ASSEMBLY Steering Linkage Wrench Assembly 3 /8" -16 Hex Nut Rear Wheel Assembly 7 3 • Fit a / 8" -16 hex nut onto the end of the rear wheel assembly . 9 • T ighten the hex nuts on both sides of the rear wheel assembly with the wrench. • T urn the vehicle so that the front end is toward you. Hint: An extra wrench has been provided to hold the hex nut • Fit the steering linkage assembly to the front end of the vehicle. on one side of
ページ12に含まれる内容の要旨
ASSEMBLY Front Axle Hubcap (Peg Side In) Hubcap Wheel Cover 13 (Rib Side In) 11 • Fit and snap a hubcap cover to the hubcap. • Fit a wheel, rib side in, onto the front axle. • Repeat Assembly steps 10-13 to assemble a washer , bushing, • Slide a hubcap, peg side in, onto the front axle. wheel, hubcap, hex nut and hubcap cover to the other front axle. Front Axle Seat Tabs Wrench 3 /8" -16 Hex Nut 12 3 14 • Fit a / 8" -16 hex nut onto each end
ページ13に含まれる内容の要旨
ASSEMBLY Label #11 Dashboard 17 BACK VIEW 15 • Lower the front end of the vehicle. 3 • Insert four #8 x /4" screws into the seat. • Apply label #11 to the dashboard, as shown. • T ighten the screws with a Phillips screwdriver . Straight End of Steering Column Steering Wheel Hole Steering Wheel Column Steering Steering Cur Curved ved Linkage Linkage End End Hole Hole 18 16 BOTTOM VIEW • Fit the steering wheel onto the end of the steering column and
ページ14に含まれる内容の要旨
ASSEMBLY Key Wrench 3 /8" -16 Hex Nut Hole in Steering Column Dashboard 21 19 • Insert and “snap” the key into the hole in the dashboard. 3 • Fit a / 8" -16 hex nut on the end of the steering column. • T ighten the hex nut with the wrench. Steering Wheel Cover Steering Wheel B A Side Window 22 FRONT VIEW 20 • First insert the tabs on the bottom edge of the side window into • At an angle, fit the tabs on one side of the steering wheel co
ページ15に含まれる内容の要旨
ASSEMBLY Slots Windshield Side Mirror 23 25 FRONT VIEW • Fit a side mirror to the side of the vehicle. • Insert and “snap” the tabs at the top of the windshield into the slots in the top edge of the vehicle. 3 #8 x /4" Screws 24 RIGHT SIDE VIEW 3 • From the inside of the vehicle, insert two #8 x /4" screws 26 through the vehicle and into the side mirror . • T ighten the screws. 3 • Insert three #8 x /4" screws into the windshield. •
ページ16に含まれる内容の要旨
ASSEMBLY VEHICLE CARE • Check all screws, hex nuts and their protective coverings regularly and tighten as required. Check plastic parts on a regular basis for cracks or broken pieces. Pretend • During snowy or rainy weather , the vehicle should be stored Engine inside or under a protective cover . Remember to charge the batter y at least once per month while your vehicle is not in regular use. • A void operating the vehicle in
ページ17に含まれる内容の要旨
DECORATION • Before applying the labels, wipe the sur face of the vehicle with a clean, dr y cloth to remove any dust or oils. • Place the labels exactly as shown in the illustrations. For best results, avoid repositioning a label once it has been applied to the vehicle. • After applying a label, rub the label firmly with a clean, dr y cloth to make sure the label is a
ページ18に含まれる内容の要旨
DECORATION 24 19 20 28 4 26 22 21 23 31 2 21 29 5 32 REAR VIEW K3033pr-0921 18
ページ19に含まれる内容の要旨
BATTERY INSTALLATION ® IMPORTANT! Use only a Power Wheels 6 volt lead-acid rechargeable batter y . Use of any other batter y will damage your vehicle. Make sure you charge the batter y for at least ® 18 hours using the enclosed Power Wheels Super 6 volt charger before operating your vehicle for the first time. Charge the batter y for at least 14 hours after each use of the ve
ページ20に含まれる内容の要旨
BATTERY CARE AND DISPOSAL Care Disposal ® If a battery leak develops, avoid contact with the leaking acid and • Y our Power Wheels batter y is a non-spillable, sealed lead-acid place the damaged batter y in a plastic bag. See information below batter y . It must be recycled or disposed of in an environmentally for proper disposal. sound manner . If acid comes in contact with skin or eyes, flush with cool water • Do not dispose of a lead-acid
