ページ1に含まれる内容の要旨
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
®
Safety Notice
MARCY CLASSIC
Hardware Identifier
INVERSION TABLE
Assembly Instruction
IVT-451
Parts List
Warranty
Ordering Parts
Model
IVT-451
Retain This
Manual for
Reference
100114
OWNER'S
MANUAL ®
IMPEX INC.
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
info@impex-fitn
ページ2に含まれる内容の要旨
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................…. 1 IMPORTANT SAFETY NOTICES..................................................................…. 2 HARDWARE IDENTIFIER.....…....................................................................…. 4 ASSEMBLY INSTRUCTIONS........................................................................…. 5 EXPLODED DIAGRAM………………………………………………………………. 11 PARTS LIST................
ページ3に含まれる内容の要旨
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a time should use t
ページ4に含まれる内容の要旨
WARNING LABEL PLACEMENT The Warning Labels shown here have been placed on the Rear Support Frame. If the labels are missing or illegible, please call customer service at 1-800-999-8899 for replacement. Apply the labels in location shown. 3
ページ5に含まれる内容の要旨
HARDWARE IDENTIFIER NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 4
ページ6に含まれる内容の要旨
ASSEMBLY INSTRUCTION Tools Required for Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended that two or more people assemble this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Do not fasten the Nuts and Bolts until instructed to do so. B.) Attach Front Support Frame (#1) to Rear Support Frame (#2). Secure them together with one M10 x 1” Allen Bolt (#34), two Ø ¾” Washers (#45), and one M10 aircraft Nut (#43) on eac
ページ7に含まれる内容の要旨
DIAGRAM 1 6
ページ8に含まれる内容の要旨
STEP 2 (See Diagram 2) A.) Attach the two Pivot Brackets (#12) to the Backrest Frame (#7) from each side. B.) Lift the Backrest Frame and insert the two Pivot Brackets into the open slot on Rear Support Frame (#2). Make sure the groves on the Pivot are attached on the slots completely and the Pivots can swing smoothly. C.) Cover the two open slots on the Rear Support Frame with Left & Right Swivel Cover (#30 & #31). DIAGRAM 2 7
ページ9に含まれる内容の要旨
STEP 3 (See Diagram 3) A.) Attach the Left Handle (#8) to Front Support Frame (#1). Secure it with one M8 x ¾” Allen Bolt (#35), one Ø 5/8” Washer (#46), and one M8 Aircraft Nut (#43). B.) Attach the Left Handle to the Rear Support Frame (#2). Secure it with one M8 x 1 ¾” Allen Bolt (#36), one Ø 5/8” Washer (#46), and one M8 Aircraft Nut (#43). C.) Slide one Plastic Barricade (#38) onto opening edge on the Rear Support Frame (#2) to prevent fingers from being caught in the opening. D.)
ページ10に含まれる内容の要旨
STEP 4 (See Diagram 4) A.) Pull up the Foot Adjustment Lock Pin (#23). Insert the Foot Lock Frame (#13) into the Adjustment Fame (#11). Push down the Pin to securely lock the Foot Lock Frame in position. B.) Insert the Foot Support (#6) into the bottom of Adjustment Frame. Secure it with one M8 x 1 5/8” Allen Bolt (#40), one Ø 5/8” Washer (#46), and one M8 Aircraft Nut (#43). C.) Insert the Foam Tube (#10) halfway through the hole on Adjustment Frame. Push two Foam Rolls (#17) onto the
ページ11に含まれる内容の要旨
STEP 5 (See Diagram 5) A.) Pull out the Backrest Adjustment Lock Pin (#22). Insert the Adjustment Frame (#11) into the opening on the vertical frame on the back of Backrest Frame (#7). Push back the Pin into the selected hole on Adjustment Frame. The holes are scaled from 5’3” to 6’6”. User can select the hole by user’s body height for better fitment while performing the inversion exercises. B.) Insert the Ring Lock Pin (#21) through the hole on the vertical frame and hole on Adjustment
ページ12に含まれる内容の要旨
EXPLODED DIAGRAM 11
ページ13に含まれる内容の要旨
PARTS LIST KEY NO. DESCRIPTION QUANTITY 1 Front Support Frame 1 2 Rear Support Frame 1 3 Short Horizontal Support 2 4 Right Long Horizontal Support 1 5 Left Long Horizontal Support 1 6 Foot Support 1 7 Backrest Frame 1 8 Left Handle 1 9 Right Handle 1 10 Foam Tube 1 11 Adjustment Frame 1 12 Pivot Bracket 2 13 Foot Lock Frame 1 14 U-shaped Lock Pin 1 15 Inversion Adjustment Belt 1 16 Curved Foam Roll 2 17 Foam Roll 2 18 Hook 2 19 Backrest 1 20 Ø 1 ¼” End Cap 4 2
ページ14に含まれる内容の要旨
® IMPEX INC. LIMITED WARRANTY ® IMPEX Inc. ("IMPEX ") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX
