ページ1に含まれる内容の要旨
Display System
Owners Manual
Customer Service Center
• N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A.
Model
89226
REQUIRED TOOLS AND MATERIALS:
WARNING!
• 2 Capable Adults • (2 each) Wrenches and/or
Socket Wrenches and
READ AND UNDERSTAND
Sockets.
OPERATOR'S MANUAL
BEFORE USING THIS UNIT.
• 2 Stepladders 7/16" 1/2" 9/16"
FAILURE TO FOLLOW
OPERATING INSTRUCTIONS
AND/OR
COULD RESULT IN INJURY
OR DAMAGE TO PROPERTY.
• Phillips Screwdriver
7/16" 1/2" 9/16"
IMPORTANT!
To ensure promp
ページ2に含まれる内容の要旨
NOTICE TO ASSEMBLERS ALL basketball systems, including those used for DISPLAYS, MUST be assembled and ballasted with sand or water according to instructions. Failure to follow instructions could result in SERIOUS INJURY. It is NOT acceptable to devise a makeshift weight system. IMPORTANT! Remove all contents from boxes. Be sure to check inside pole sections; hardware and additional parts are packed inside. SAFETY INSTRUCTIONS FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS IN
ページ3に含まれる内容の要旨
PARTS LIST (See Hardware Identifier) Item Qty. Part No. Description Item Qty. Part No. Description 1 2 200318 Bracket, Reinforcement S/J 17 2 203795 Nut, 3/8-16 Special S/J 2 1 200503 P/S Cover 18 2 203796 T-bolt, 3/8-16 x 5" 3 2 200520 Screw, #8 x 3/4", Flat Head, Phillips 19 1 203798 Bolt, Hex 5/16-18 x 1.5" 4 2 200533 Spacer, Mounting 20 4 204290 Net 5 3 990062 Pole, 3.5" 21 1 206219 Pole Cap, 3" 6 3 201344 Plastic Knob 22 3 207103 Pole Cap, 3.5" 7 12 201611 Bolt,Hex-Flange, 5/16-18 x 3" 23 2
ページ4に含まれる内容の要旨
Install display boards in the marked locations. Each mounting location consists of a mounting pole stub with the following dimensions: Height = 8”, O.D. = 3 3/8”, I.D. = 3 1/8” (arrows indicate direction the board is facing). Display Stand - Top View 3-1/2" 3" Corner “4” Corner “3” 80602 61259 Corner “2” Corner “1” 73256 9H235A 3-1/2" 3-1/2" Display boards will be mounted as follows: Corner Location 1: 9H235A • 48” SFA Board • Titanium II Logo • Black Slam Jam Goal with Cover • Use extension a
ページ5に含まれる内容の要旨
Slide the 3" diameter end of the display pole (24) 1. inside the pole sleeve. Secure the display pole by sliding the display 24 wedge (27) into position as shown. To lock the display pole in place, tighten the hex-bolt (19). 24 27 19 At corner location 1, 2 and 4 slide 2. the 3-1/2" diameter end of the display pole (5) outside the mounting stubs. 5 09/06 ID# M890001 5
ページ6に含まれる内容の要旨
Corner Location 1: STEEL FRAME ACRYLIC BACKBOARD ASSEMBLY Display Stand - Top View 31 11 11 3-1/2" 3" Corner “4” Corner “3” 80602 61259 32 4 Corner “2” Corner “1” 4 73256 9H235A 3-1/2" 3-1/2" 18 Insert “T” bolt (18) through Slam Jam bracket (23) as shown. 1. Secure Slam Jam bracket (23), extension arm (31) and 23 mounting spacers (4) assemblies to backboard using bolt (7 ) 7 and nut (11) as shown. Attach board assembly to pole. 2. 32 WARNING! TWO CAPABLE ADULTS REQUIRED FOR THIS PROCEDURE. FAILU
ページ7に含まれる内容の要旨
• Fit rim (25) securely into bracket (23) as shown. NOTE: 3. • Install reinforcement bracket (1) onto “T” bolt (18) as shown. Tighten nut (17) until flush with end of "T" bolt (18) as • Install spring (16) onto “T” bolt (18) as shown. shown here. • Install special nut (17) and washer (15) onto “T” bolt (18). 25 17 18 NOTE: 15 Peel protective 23 film from surface 16 of acrylic backboard prior to 1 use. Apply logo label (8) to rim cover (2). Attach cover (2) to rim using 4. 5. screws (3). 3 25 2
ページ8に含まれる内容の要旨
Corner Location 2: 48” FAN MOLDED PLASTIC BOARD ASSEMBLY Display Stand - Top View 11 31 3-1/2" 3" Corner “4” Corner “3” 80602 61259 28 Corner “2” Corner “1” 73256 9H235A 3-1/2" 3-1/2" Insert “T” bolt (18) through Slam Jam bracket 1. 18 (23) as shown. 23 Secure Slam Jam bracket (23) and extension arm (31) to backboard using bolt (7) and nut 18 (11) as shown. Tighten completely. 7 7 2. Attach board assembly to pole. 28 WARNING! TWO CAPABLE ADULTS REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS
ページ9に含まれる内容の要旨
• Fit rim (25) securely into bracket (23) as shown. 3. • Install reinforcement bracket (1) onto “T” bolt (18) as shown. • Install spring (16) onto “T” bolt (18) as shown. • Install special nut (17) and washer (15) onto “T” bolt (18). NOTE: Tighten nut (17) until flush with end of "T" bolt (18) as shown here. 25 17 18 15 1 16 23 09/06 ID# M890001 9
ページ10に含まれる内容の要旨
Corner Location 3: 44" FAN MOLDED PLASTIC BOARD ASSEMBLY Pole bracket will need to be lightly pressed into 1. Display Stand - Top View backboard ribbing. Be sure to press completely into place. Attach rim (25) to backboard and pole bracket (26) with knob (6), reinforcement bracket (1), and carriage bolt (10) as shown. Tighten knob completely. 3-1/2" 3" Corner “4” Corner “3” 80602 61259 WARNING! KNOB MUST BE TIGHTENED COMPLETELY AND CHECKED FOR TIGHTNESS BEFORE EACH USE. 29 Corner “2” Corner “1”
ページ11に含まれる内容の要旨
Corner Location 4: 44" FAN MOLDED PLASTIC BOARD ASSEMBLY Display Stand - Top View 11 11 31 3-1/2" 3" Corner “4” Corner “3” 80602 61259 30 Corner “2” Corner “1” 73256 9H235A 3-1/2" 3-1/2" Attach rim (25) to backboard (30) and 1. 14 14 extension arm (31) with bolts (7), washers (14) and nuts (11). Tighten completely. 7 25 Attach board assembly to pole. 2. 30 WARNING! TWO CAPABLE ADULTS REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE
