ページ1に含まれる内容の要旨
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
MARCY HOME GYM
Hardware Pack
MWM-1100
Assembly Instruction
Parts List
Resistance Chart
Warranty
Ordering Parts
Model
MWM-1100
Retain This
Manual for
Reference
08-10-09
®
IMPEX INC.
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
OWNER'S
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
MANUAL
info@impe
ページ2に含まれる内容の要旨
TABLE OF CONTENTS BEFORE YOU BEGIN....................................................................................……….. 1 IMPORTANT SAFETY NOTICES...................................................................……….. 2 HARDWARE IDENTIFIER.....….....................................................................……….. 4 ASSEMBLY INSTRUCTIONS.........................................................................……….. 7 EXPLODED DIAGRAM………………………………………………………………………19 PARTS
ページ3に含まれる内容の要旨
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a ti
ページ4に含まれる内容の要旨
WARNING LABEL PLACEMENT The warning labels shown here have been placed on the Rear Stabilizer and Upper Frame. If the labels are missing or illegible, please call customer service at 1-800-999-8899 for replacements. Apply the labels in the location shown. 3
ページ5に含まれる内容の要旨
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 4
ページ6に含まれる内容の要旨
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 5
ページ7に含まれる内容の要旨
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 6
ページ8に含まれる内容の要旨
ASSEMBLY INSTRUCTION Tools Required for Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended that this machine to be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Slide two Ø 2 ½” x 1” Rubber Bumpers (#35) onto the two Guide Rods (#5). Insert the two Guide Rods into the holes on the Rear Stabilizer (#2). Secure each Guide Rod with one M10 x 1” Allen Bolt (#62) and one ∅ ¾” Washer (#70) from
ページ9に含まれる内容の要旨
STEP 2 (See Diagram 2) A.) Slide 9 Weight Plates (#50) onto the Guide Rods (#5). Make sure the deep groove on the Weight Plate are facing down and toward the back of the Machine. B.) Align the holes on the Weight Plates. Insert a Selector Rod (#16) through the center hole. Use the L-shaped Pin (#57) to select the number of Weight Plates for exercise. Each Plate weighted approx. 10lbs. Please refer to the Weight Resistance Chart in page 21. C.) Slide Selector Stem (#49) down the Guide Ro
ページ10に含まれる内容の要旨
DIAGRAM 2 9
ページ11に含まれる内容の要旨
STEP 3 (See Diagram 3) A.) Attach the Seat Support (#9) to the Vertical Frame (#3). Secure it with two M10 x 2 ½” Carriage Bolts (#60), one 5 1/8” x 1 5/8” Bracket (#21), two Ø ¾” Washers (#70), and two M10 Aircraft Nuts (#72). B.) Place the Seat Pad (#25) onto the Seat Support. Secure it with two M8 x 2 3/8” Allen Bolts (#68) and two Ø 5/8” Washers (#69). C.) Attach two ∅ ¾” Leg Developer Bushings (#54) to the Leg Developer (#9). Attach the Leg Developer to the bracket on the Seat
ページ12に含まれる内容の要旨
STEP 4 (See Diagram 4) A.) Attach two Ø 1” x Ø ½” Bushings (#53) to the holes on Upper Frame (#4). Attach the Front Press Base (#6) to the two Bushings. Secure it with one M12 x 3 3/8” Hex Bolt (#61), two Ø 1” Washers (#71), and one M12 Aircraft Nut (#73). Do not over tighten the Nut and Bolt. B.) Insert the axle on the Right Butterfly (#8) through the hole on the Front Press Base from the bottom. Slide a Lock Ring (#41) onto the axle. Align the holes and secure it with one M6 x 1 3/8”
ページ13に含まれる内容の要旨
DIAGRAM 4 12
ページ14に含まれる内容の要旨
CABLE LOOP DIAGRAM 13
ページ15に含まれる内容の要旨
STEP 5 (See Diagram 5 & Cable Loop Diagram) A.) Attach the 136” Upper Cable (#26) to the front opening on the Upper Frame (#4). NOTE: The Ball Stopper on the Cable needs to be underneath the Frame. B.) Attach a Pulley (#38) to the forward most opening. Secure it with one M10 x 2 3/8” Allen Bolt (#64), two Ø 1” x ½” Pulley Bushings (#39), and one M10 Aircraft Nut (#72). C.) Draw the Cable towards the back of the machine to the second opening on the Upper Frame. Repeat Step B above to i
ページ16に含まれる内容の要旨
14 DIAGRAM 5 15
ページ17に含まれる内容の要旨
STEP 6 (See Diagram 6 & Cable Loop Diagram) A.) Attach one end of the 108” Butterfly Cable (#27) to the hook on the Right Butterfly (#8). Draw the Cable towards the right open Swivel Pulley Bracket (#17). B.) Attach a Pulley (#38) to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#63), two ∅ ¾” Washers (#70), and one M10 Aircraft Nut (#72). C.) Draw the Cable over the Pulley then pull downward. Attach the Cable to an Angled Double Floating Pulley Bracket (#18). Install a Pulley
ページ18に含まれる内容の要旨
STEP 7 (See Diagram 7 & Cable Loop Diagram) A.) Attach the 142” Lower Cable (#28) to the opening on the bottom of the Leg Developer (#10). B.) Attach a Pulley (#38) to the opening. Secure it with one M10 x 2 3/8” Allen Bolt (#64), two ∅ 1” x ½” Pulley Bushings (#39), and one M10 Aircraft Nut (#72). C.) Draw the Cable underneath the Pulley towards the back of the machine to the opening on the bottom of Vertical Frame (#3). D.) Repeat Step B to install a Pulley. E.) Pull the Cable
ページ19に含まれる内容の要旨
DIAGRAM 7 18
ページ20に含まれる内容の要旨
19
