ページ1に含まれる内容の要旨
NOTE:
Please read all instructions
carefully before using this
product
DELUXE SMITH MACHINE
Table of Contents
MSS-1280
Safety Notice
Hardware Identifier
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
MSS-1280
Retain This
Manual for
Reference
08-03-09
OWNER'S
MANUAL
®
IMPEX INC.
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
info@impex-fitness.com
ページ2に含まれる内容の要旨
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... 1 IMPORTANT SAFETY NOTICES..................................................................... 2 SMITH MACHINE HARDWARE PACK……….....….......................................... 4 SMITH MACHINE ASSEMBLY INSTRUCTIONS...............................................6 SMITH MACHINE EXPLODED DIAGRAM........................................................15 SMITH MACHINE
ページ3に含まれる内容の要旨
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a
ページ4に含まれる内容の要旨
WARNING LABEL PLACEMENT The warning labels shown here have been placed on the back of Rear Support, and Upper Frame. If the labels are missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the labels in the location shown. 3
ページ5に含まれる内容の要旨
SMITH MACHINE HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 4
ページ6に含まれる内容の要旨
CAGE MACHINE HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 5
ページ7に含まれる内容の要旨
SMITH MACHINE ASSEMBLY INSTRUCTION Tools Required for Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended that two or more people assemble this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Note: Do not tighten the Nuts and Bolts until instructed to do so. B.) Connect the two Base Frames (#3) by the Cross Brace (#7). Secure each end of the Cross Brace to each Base Frame with four M10 x 2 3/8” Carriage Bolts (#50), one
ページ8に含まれる内容の要旨
STEP 2 (See Diagram 2) A.) Do not tighten Nuts and Bolts until instructed to do so. B.) Attach the Left Upright Beam (#1) to the Left Rear Support (#5) and onto the left Base Frame (#3). C.) Secure it to the Base Frame with two M10 x 4” Allen Bolts (#54), four Ø ¾” Washers (#57), and two M10 Aircraft Nuts (#58). D.) Secure it to the Left Rear Support with one M10 x 4” Carriage Bolt (#48), one Ø ¾” Washer (#57), and one M10 Aircraft Nut (#58) from side. Secure with one M10 x 5/8” Allen B
ページ9に含まれる内容の要旨
DIAGRAM 2 8
ページ10に含まれる内容の要旨
STEP 3 (See Diagram 3) A.) Attach two Ø 2 3/8” x 2” Rubber Bumpers (#30) to the holes on the Cross Brace (#7). Insert the two Rear Short Guide Rods (#17) through the two Rubber Bumpers into the holes on Cross Brace. B.) Secure each Guide Rod to the Cross Brace with one M10 x ¾” Allen Bolt (#56) and one Ø ¾” Washer (#57) from bottom. C.) Slide the Sliding Weight Post (#16) onto the two Rear Short Guide Rods. Make sure the Pulley bracket on the Weight Sliding Frame faces upward. D.) At
ページ11に含まれる内容の要旨
DIAGRAM 3 10
ページ12に含まれる内容の要旨
CABLE LOOP DIAGRAM 11
ページ13に含まれる内容の要旨
STEP 4 (See Diagram 4 & Cable Loop Diagram) A.) Attach the 170” Upper Cable (#25) to the opening on the Front Upper Frame (#14). B.) Attach a Pulley (#33) to the opening. Secure it with one M10 x 4” Allen Bolt (#54), two Ø ¾” Washers (#57), and one M10 Aircraft Nut (#58). C.) Draw the Cable over the Pulley toward the back of the machine. Note: The Ball stopper on the Cable needs to be under the Frame. D.) Draw the Cable to the first opening on the Rear Upper Frame. Repeat B to install a P
ページ14に含まれる内容の要旨
STEP 5 (See Diagram 5 & Cable Loop Diagram) A.) Attach the 62” Lower Cable (#26) to the open bracket on the Cross Brace (#7). Attach a Pulley (#33) to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#52), two Ø ¾” Washers (#57), one L-shaped Cable Retainer (#24), and one M10 Aircraft Nut (#58). B.) Draw the Cable underneath the Pulley then upward to the 170” Upper Cable (#25) installed in Step-4. C.) Connect the Lower Cable to a Hook (#36). Connect the Hook to the 5-link Chain (#44
ページ15に含まれる内容の要旨
STEP 6 (See Diagram 6) A.) Place the Lifting Sleeve (#8) in between the two Safety Stop Frames (#18). Align the holes. Insert the Weight Bar (#13) from outside of one Safety Stop Frame through the Lifting Sleeve to the other Safety Stop Frame on the other side. B.) Turn and attach the two safety catch hooks on the Lifting Sleeve (#8) to the selected slots on the Left and Right Uptight Beams (#1 & #2). C.) Attach two Weight Bar Sleeves (#35) onto the Weight Bar from both ends. Attach
ページ16に含まれる内容の要旨
SMITH MACHINE EXPLODED DIAGRAM 15
ページ17に含まれる内容の要旨
SMITH MACHINE PART LIST KEY NO. DESCRIPTION Q’ty 1 Left Upright Beam 1 51 M10 x 1” Allen Bolt 1 2 Right Upright Beam 1 52 M10 x 1 ¾” Allen Bolt 2 3 Base Frame 2 53 M10 x 4 1/8” Allen Bolt 2 4 Top Beam 1 54 M10 x 4” Allen Bolt 7 5 Left Rear Support 1 55 M10 x 3 ½” Allen Bolt 4 6 Right Rear Support 1 56 M10 x ¾” Allen Bolt 12 7 Cross Brace 1 57 Ø ¾” Washer 58 8 Lifting Sleeve 1 58 M10 Aircraft Nut 28 9 Lower Left Safety Stop Frame 1 59 ST3.8 Philips Screw 24 10 Lower R
ページ18に含まれる内容の要旨
BENCH HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 17
ページ19に含まれる内容の要旨
BENCH HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 18
ページ20に含まれる内容の要旨
BENCH ASSEMBLY INSTRUCTION STEP 1 (See Diagram 1) A.) Attach the Bench Base Frame (#6) to the Rear Stabilizer (#7). Secure the side-holes with two M10 x 4” Carriage Bolts (#41), two Ø ¾” Washers (#31), and two M10 Aircraft Nuts (#33). Secure the top hole with one M10 x 5/8” Allen Bolt (#36) and one Ø ¾” Washer (#31). B.) Attach the Wheel Set (#25) to the bracket on Rear Stabilizer. Secure it with one M8 x 5 1/8” Allen Bolt (#35), two Ø 5/8” Washers (#30), and one M8 Aircraft Nut (#3
