ページ1に含まれる内容の要旨
NOTE:
Please read all instructions
carefully before using this
product
HOME GYM
Table of Contents
MSS-1600
Safety Notice
Hardware Pack
Assembly Instruction
Parts List
Resistance Chart
Warranty
Ordering Parts
Model
MSS-1600
Retain This
Manual for
Reference
08-14-09
®
IMPEX INC.
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
OWNER'S
www.impex-fitness.com
MANUAL
info@impex-fitn
ページ2に含まれる内容の要旨
TABLE OF CONTENTS BEFORE YOU BEGIN....................................................................................……….. 1 IMPORTANT SAFETY NOTICES...................................................................……….. 2 HARDWARE IDENTIFIER.....….....................................................................……….. 4 ASSEMBLY INSTRUCTIONS.........................................................................……….. 7 EXPLODED DIAGRAM………………………………………………………………
ページ3に含まれる内容の要旨
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a tim
ページ4に含まれる内容の要旨
WARNING LABEL REPLACEMENT The warning labels shown here have been placed on the Rear Stabilizer and Upper Frame. If the labels are missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the labels in the location shown. 3
ページ5に含まれる内容の要旨
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 4
ページ6に含まれる内容の要旨
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 5
ページ7に含まれる内容の要旨
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 6
ページ8に含まれる内容の要旨
HARDWARE PACK 7
ページ9に含まれる内容の要旨
ASSEMBLY INSTRUCTION Tools Required for Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended that this machine to be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Insert the two Guide Rods (#5) into the holes on the Rear Stabilizer (#2). Secure each Guide Rod with one M10 x 1” Allen Bolt (#65) and ∅ ¾” Washer (#74) from the bottom. Slide two Ø2” Rubber Bumpers (#50) onto the Guide Rods. B.
ページ10に含まれる内容の要旨
STEP 2 (See Diagram 2) A.) Slide 9 Weight Plates (#29) onto the Guide Rods (#5). Make sure the deep groove on the Weight Plates all face the back of the machine and downward. Align the holes on the Weight Plates. Insert a Selector Rod (#14) through the center hole. Use a Weight Selector Pin (#36) to select the number of Weight Plates to exercise. Note: Each Weight Plate weights approximately 10 lbs. Please refer to the Weight Resistance Chart in page 23. B.) Slide the Selector Stem (#28
ページ11に含まれる内容の要旨
DIAGRAM-2 10 STEP 3 (See Diagram 3)
ページ12に含まれる内容の要旨
A.) Attach the Seat Support (#9) to Vertical Frame (#3). Secure it with two M10 x 2 3/8” Carriage Bolts (#61), one 5 1/8” Curved Bracket (#22), two Ø ¾” Washers (#74), and two M10 Aircraft Nuts (#76). B.) Place the Seat (#26) onto the Seat Support. Secure it with two M8 x 2 1/8” Allen Bolts (#71) and Ø 5/8” Washers (#73). C.) Attach the Arm Curl Pad (#27) to Arm Curl Stand (#77). Secure it with two M8 x 5/8” Allen Bolts (#72) and two Ø 5/8” Washers (#73). Insert the Arm Curl Stand into the
ページ13に含まれる内容の要旨
A.) Attach two Ø 1” Bushings (#41) to the holes on Upper Frame (#4). Attach the Front Press Base (#6) to the Bushings. Secure it with one M12 x 4 ½” Allen Bolt (#62), two Ø 1” Washers (#75), and one M12 Aircraft Nut (#67). Do not over tighten the Nuts. Make sure the Front Press Base can move freely. B.) Attach the Left Butterfly (#7) to Front Press Base (#3). Secure it with one M12 x 4 3/8” Allen Bolt (#63), two Ø 1” Washers (#75), and one M12 Aircraft Nut (#67). Repeat the Procedure to i
ページ14に含まれる内容の要旨
DIAGRAM 4 13
ページ15に含まれる内容の要旨
CABLE LOOP DIAGRAM 14
ページ16に含まれる内容の要旨
STEP 5 (See Diagram 5 & Cable Loop Diagram) A.) Attach the 114” Upper Cable (#32) to the open bracket under the Upper Frame (#4). NOTE: The Ball Stopper on the Cable needs to be underneath the Frame. B.) Attach a Pulley (#43) to the open bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#66), two Ø ¾” Washers (#74), and one M10 Aircraft Nut (#76). C.) Draw the Cable under the Upper Frame towards the back of the machine to the next open bracket under the Upper Frame. Repeat Step B abov
ページ17に含まれる内容の要旨
DIAGRAM 5 16
ページ18に含まれる内容の要旨
STEP 6 (See Diagram 6 & Cable Loop Diagram) A.) Attach one end of the 119” Butterfly Cable (#31) to the hook on the Left Butterfly (#7). Draw the Cable towards the left open Swivel Pulley Bracket (#12). B.) Attach a Pulley (#43) to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#66), two ∅ ¾” Washers (#74), and one M10 Aircraft Nut (#76). C.) Draw the Cable over the Pulley then pull downward. Attach the Cable to an Angled Double Floating Pulley Bracket (#13). Install a Pulley as
ページ19に含まれる内容の要旨
STEP 7 (See Diagram 7 & Cable Loop Diagram) A.) Attach the 130” Lower Cable (#30) to the opening on the bottom of the Leg Developer (#10). B.) Attach a Pulley (#41) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#68), two ∅ 7/8” Pulley Bushings (#39), and one M10 Aircraft Nut (#76). C.) Draw the Cable underneath the Pulley towards the back of the machine to the open bracket on the back of the Vertical Frame (#3). D.) Attach a Pulley to the bracket. Secure it with one M10 x
ページ20に含まれる内容の要旨
DIAGRAM 7 19
