ページ1に含まれる内容の要旨
Design Wash 1400E
Elation Professional
6122 S. Eastern Ave
Los Angeles, Ca. 90040
Rev. 08/08/2008-visage
ページ2に含まれる内容の要旨
Design Wash 1400E™ CONTENTS 1. General Information……………………………………………………………………… 4 a. Introduction………………………………………………………………………. 4 b. Customer Support…………………………………………….………………… 3 c. Warranty Registration……………………………………………………..……. 5 d. Discharge Lamp Warning………………………………………………………. 5 2. Safety Instructions………………………………………………………........…………. 7 3. Features…………………………………………………………………………………… 9 4. General Guidelines………………………………………………………………………. 10 5. Lamp Installation………………………………………………………………………….
ページ3に含まれる内容の要旨
Design Wash 1400E™ 1. GENERAL INFORMATION INTRODUCTION: Congratulations, you have just purchased one of the most innovative and reliable lighting fixtures on the market today! The Design Wash 1400E,™ has been designed to perform reliably for years when the guidelines in this booklet are followed. Please read and understand the instructions in this manual carefully and thoroughly before attempting to operate this unit. These instructions contain important information regarding safet
ページ4に含まれる内容の要旨
Design Wash 1400E™ Please do not discard the shipping carton in the trash, keep for warranty repair. Please recycle whenever possible. WARRANTY REGISTRATION: The Design Wash 1400E™ carries a two year (730 days) limited warranty. Please fill out the enclosed warranty card to validate your purchase. All returned service items whether under warranty or not, must be freight pre-paid and accompany a return authorization (R.A.) number. The R.A. number must be clearly written on the outs
ページ5に含まれる内容の要旨
Design Wash 1400E™ high-pressure environment to emit a brilliant output. Due to the high pressure involved with the construction of the lamp, the lamp may explode during prolonged extensive use. This risk is increased with age; added care is encouraged when dealing with older lamps. Thus, lamp should always be replaced at the end of their recommended duty cycle. Extreme caution should be used when operated this or any fixture fitted with a gas discharge lamp. Never open this fixtur
ページ6に含まれる内容の要旨
Design Wash 1400E™ 2. SAFETY INSTRUCTIONS The Design Wash 1400E™ is an extremely sophisticated piece of electronic equipment. To guarantee a smooth operation, it is important to follow the guidelines in this manual. The manufacturer of this device will not accept responsibility for damages resulting from the misuse of this fixture due to the disregard of the information printed in this manual. 1. Always be sure that the fan and the air inlets remain clean and are never bloc
ページ7に含まれる内容の要旨
Design Wash 1400E™ may increase the risk of damage and/or personal injury. 10. To reduce the risk of fire or electric shock, do not expose this fixture to rain or moisture. 11. Do not attempt to operate this fixture if the power cord has become damaged or frayed. Important Notice: Damages resulting from the disregard of safety and general user instructions found in this user manual are not subject to any warranty claims. ©Elation Professional®
ページ8に含まれる内容の要旨
Design Wash 1400E™ 3. FEATURES • Pan 630° or 540˚ (User selectable) / Tilt 265° • 30 Built-In Color Preset Macros • 3 operation mode: DMX Controlled, Stand-Alone or Sound Activated • 2 Color Wheels (Replaceable Filters) o Wheel 1: 4 Colors plus White o Wheel 2: 2 Colors plus CTB, UV & White • CMY & CTO Variable Color Mixing for Infinite Color Possibilities • Easy to Navigate, Full Color, On-Board LCD Menu (may be turned 180°) • Strobe Effect: 0~10 flashes per second • Moto
ページ9に含まれる内容の要旨
Design Wash 1400E™ 4. GENERAL GUIDELINES This fixture is a professional lighting effect designed for use on stage, in nightclubs, in theatres, etc. Do not attempt operation or installation without a proper knowledge on how to do so. This fixture was designed for indoor use only. Consistent operational breaks may ensure that the fixture will function properly for many years to come. Do not shake the fixture around. Avoid brute force when installing or operating the device.
ページ10に含まれる内容の要旨
Design Wash 1400E™ 5. FIXTURE OVERVIEW 1. Head 2. Output Lens 3. Yoke 4. Antenna 5. Base 6. Full Color LC-Display 7. Menu Jog Wheel 8. Mode/esc Button 9. Enter Button 10. Software update socket 11. Lamp Cover 12. Carrying Handle 13. Power Cord 14. Fuse 1 15. Fuse 2 16. 3-Pin DMX Input 17. 5-Pin DMX Input 18. 3-Pin DMX Output 19. 5-Pin DMX Output 20. ©Elation Professional® 10 Design Wash 1400E™
ページ11に含まれる内容の要旨
Design Wash 1400E™ 6. LAMP INSTALLATION INSTRUCTIONS For a proper and safe lamp change, please read this chapter carefully and follow all instructions. Safety Regulations • Disconnect the unit’s main power supply. • Allow the unit to cool for at least 15 minutes before attempting any type of service. • Before you put the Design Wash 1400E™ back into operation after a lamp change, be sure all covers have been replaced and/or closed and secured. Operating the fixture with the co
ページ12に含まれる内容の要旨
Design Wash 1400E™ FastFit). 4. Once the lamp has been inserted and secured into the socket, follow the lamp optimization instructions outlined below, then lock the lamp cover back in to place. 5. Reset the lamp run time in the system menu. 6. Always be sure to optimize the lamp after lamp replacement. Caution! Do not attempt to operate this fixture without the protective covers in tacked. Lamp Optimization The lamp orientation and optimization must be adjusted after e
ページ13に含まれる内容の要旨
Design Wash 1400E™ Please remember that a MSR Gold 1200 FastFit lamp is not a hot-restrike lamp therefore, you must wait approximately 15 minutes before you can attempt to strike the lamp once it has been turned off. ©Elation Professional® 13 Design Wash 1400E™
ページ14に含まれる内容の要旨
Design Wash 1400E™ 7. MOUNTING AND INSTALLATION Cautions: For added protection mount the fixtures in areas outside walking paths, seating areas, or in areas were unauthorized personnel might reach the fixture. Before mounting the fixture to any surface, make sure that the installation area can hold a minimum point load of 10 times the device’s weight. Fixture installation must always be secured with a secondary safety attachment, such as an appropriate safety cable. Never
ページ15に含まれる内容の要旨
Design Wash 1400E™ Mounting points Overhead mounting requires extensive experience, including amongst others calculating working load limits, a fine knowledge of the installation material being used, and periodic safety inspection of all installation material and the fixture. If you lack these qualifications, do not attempt the installation yourself. Improper installation can result in bodily injury. CAUTION! Be sure a qualified electrician performs all electrical connectio
ページ16に含まれる内容の要旨
Design Wash 1400E™ yoke. As an added safety measure be sure to attached at least one properly rated safety cable to the fixture using on of the safety cable rigging point integrated in the bracket assembly Securing the Design Wash 1400E™ Regardless of the rigging option you choose for your Design Wash 1400E™ always be sure to secure your fixture with a safety cable. The fixture provides a built-in rigging point for a safety cable on the hanging bracket as illustrated above. B
ページ17に含まれる内容の要旨
Design Wash 1400E™ 8. UNDERSTANDING DMX DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used by most lighting and controller manufactures as a form of communication between intelligent fixtures and controllers. DMX allows all makes and models of different manufactures to be linked together and operate from a single controller. This is possible as long as all the fixtures and the controller are DMX compliant. A DMX controller sends the DMX data instruction
ページ18に含まれる内容の要旨
Design Wash 1400E™ Be sure to follow the above figure when making your own cables. Do not use the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR’s outer casing. Grounding the shield could cause a short circuit and erratic behavior. DMX-512 control connection Connect the provided XLR cable to the female 3-pin XLR output of your controller and the other side to the m
ページ19に含まれる内容の要旨
Design Wash 1400E™ DMX-512 connection with DMX terminator A DMX terminator should be used in all DMX lines especially in longer runs. The use of a terminator may avoid erratic behavior in your DMX line. A terminator is a 120 ohm 1/4 watt resistor that is connected between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This fixture is inserted in the female XLR connector of the last fixture in your daisy chain to terminate the line. Using a line terminator (Elation part: DM
ページ20に含まれる内容の要旨
Design Wash 1400E™ channel number from which the fixture starts to “listen” to the digital control information sent out from the DMX controller. The allocation of this starting DMX address is achieved by setting the correct DMX address on the digital display located on the head of the fixture. You can set the same starting address for all fixtures or a group of fixtures, or set different address for each individual fixture. Be advised that setting all you fixtures to the same DMX a
