ページ1に含まれる内容の要旨
Owner’s Manual
™
SmartOnline 3-Phase 20kVA & 30kVA
Intelligent True On-Line UPS Systems
Input/Output Voltage: 120/208V AC, 3ø, 4 wire (plus ground), wye
Important Safety Warnings
2
Front Panel 3
5
Rear Panel
Installation 6
Operation (Normal Conditions) 7
Operation (Special Conditions) 8
10
Communications
Adding or Replacing Internal Batteries 11
Service 16
Warranty & Warranty Registration 16
Specifications
17
Español 19
Français 38
1111 W. 35th Street • Chicago, IL 60609 USA
(773) 869-1234 � www
ページ2に含まれる内容の要旨
Important Safety Warnings SAVE THESE INSTRUCTIONS. This manual contains important instructions and warnings that should be followed during the installation and maintenance of all Tripp Lite SmartOnline 3-Phase 20kVA and 30kVA UPS Systems. UPS Location Warnings • Install your UPS in a controlled environment. • Install your UPS indoors, away from heat, direct sunlight, dust, and excess moisture or other conductive contaminants. • Install your UPS in a structurally sound area that is level. Your UP
ページ3に含まれる内容の要旨
Front Panel Familiarize yourself with the location and function of the features on your UPS system before installing and operating it. CONTROL PANEL 13 4 3 6 7 2 1 12 5 89 10 11 1. “ON” Button: This button turns the UPS System's inverter ON. 2. “OFF” Button: This button turns the UPS System's inverter OFF. NOTE: If the UPS System remains off for an extended period of time, it should be turned back on periodically to allow the internal batteries to recharge. The UPS System should be turned on an
ページ4に含まれる内容の要旨
Front Panel (continued) BATTERY ACCESS PANEL (cover removed) Individual models may vary slightly from diagram. 1 4 3 2 7 5 6 1. Internal Battery Packs: These supply backup runtime to connected equipment. Each pack consists of two strings (one positive and one negative). The number of included battery packs varies depending on UPS model number. Battery packs must replaced by a qualified electrician. See “Adding or Replacing Internal Batteries” section for details. 2. Battery Cartridge Fuses: Pro
ページ5に含まれる内容の要旨
Rear Panel REAR PANEL Individual models may vary slightly from diagram. 9 8 6 11 5 7 10 12 3 2 1 15 4 13 15 14 1. Manual Bypass Switch: This dial is used to put the UPS in “BYPASS” mode, which must be done before performing any maintenance on the UPS with the connected load supported. [See “Operation (Special Conditions)” for step-by-step instructions for going into “BYPASS.”] While this switch is on “BYPASS,” connected equipment will receive filtered AC mains power, but will not receive battery
ページ6に含まれる内容の要旨
Installation UPS LOCATION Move your UPS over short distances using its wheels. NOTE: the wheels are not designed to provide long-term support for the UPS system after final installation. Mounting bracket installation is required. MOUNTING BRACKET INSTALLATION DANGER! RISK OF PRODUCT DAMAGE AND SERIOUS PERSONAL INJURY The UPS System's wheels are not designed to provide long-term support for the UPS system after final installation. MOUNTING BRACKET INSTALLATION IS REQUIRED. If the mounting brack
ページ7に含まれる内容の要旨
Installation (continued) WIRING CONNECTION Connect your wiring to the input and output terminal blocks located on the rear panel of your UPS (see figure below). CAUTION! Qualified personnel should follow all procedures prescribed by N.E.C. and other local codes for hardwiring devices to a utility source. G N1 R1 S1 T1 Ensure that cables are fitted with cable sleeves and are secured by connector clamps. Tighten connections with a torque of not less than 35 inch-pounds. Observe the appropriate c
ページ8に含まれる内容の要旨
Operation (Normal Conditions) (continued) LCD DISPLAY SELECT BUTTON Momentarily press the “SELECT” button on the front panel to browse through different power readings on the LCD Display. BYPASS OUTPUT R: XXXV R: XXX.XV (Bypass & Output Voltage) S: XXXV S: XXX.XV T: XXXV T: XXX.XV Press "SELECT" Button OUTPUT LOAD R: XXX% XXX.XA (Output Load & Current) S: XXX% XXX.XA T: XXX% XXX.XA Press "SELECT" Button MAINS INVERTER R: XXXV R: XXX.XV (Mains & Inverter Voltage) S: XXXV S: XXX.XV T:
ページ9に含まれる内容の要旨
Operation (Special Conditions) (continued) INVERTER ON WARNINGS When the inverter is ON, the LCD Display may show any one of the following warnings: Condition LCD Display Message UPS Output Overload OVERLOAD 110% UPS Charger Failure CHARGER FAILURE Abnormal Input Frequency FREQUENCY ERROR Abnormal Input Phase PHASE ABNORMAL! Battery is Depleting* ON BATTERY Battery Charge is Nearly Depleted* BATTERY LOW * During a prolonged blackout, users should save files and shut down connected equipment. Th
ページ10に含まれる内容の要旨
Communications RS-232 INTERFACE This female DB9 port connects your UPS via an RS-232 cable to a workstation or server equipped with Tripp Lite software. The port uses RS-232 communications to report UPS status and power conditions. Using this port, Tripp Lite software can monitor and manage network power and automatically save open files and shut down equipment during a blackout. Contact Tripp Lite Customer Support at (773) 869-1234 for information on available SNMP, network management and conne
ページ11に含まれる内容の要旨
Communications (continued) REMOTE EMERGENCY POWER OFF (EPO) This optional feature is only for those applications which require connection to a facility's Emergency Power Off (EPO) circuit. When the UPS System is connected to this circuit, it enables emergency shutdown of the output. Using a user-supplied cable, connect the UPS System's EPO port to a user- supplied remote switch. The EPO port is not a phone line surge suppressor; do not connect a phone line to this port. The pin assignments for t
ページ12に含まれる内容の要旨
Adding or Replacing Internal Batteries (continued) INTERNAL BATTERY PACK WIRING DIAGRAM Qualified service personnel should familiarize themselves with the battery pack wiring diagram prior to adding or replacing batteries. The battery module can accept up to four battery packs (each pack consisting of two strings). The diagram shows all four battery packs connected for illustrative purposes only. The actual number of batteries shipped with the UPS System varies depending on model number. White
ページ13に含まれる内容の要旨
Adding or Replacing Internal Batteries (continued) 1 Place the UPS System in Bypass Mode or completely turn it off, depending on preference. See “Operation of Manual Bypass Switch” or “Turning the UPS Off” in the Operation section. Remove battery access panel, located on the FRONT of the UPS 2 2 system. 3 Disconnect the RED and BLACK cables attached to each internal 3 battery pack. Remove the battery cartridge fuses from each fuse block. 4 4 Save the fuses. Disconnect the BLUE and WHITE jumper
ページ14に含まれる内容の要旨
Adding or Replacing Internal Batteries (continued) Remove the fuse block bracket. 6 6 7 Slide the battery string with the RED cable into an empty slot within 7 the battery compartment as shown. Make sure that the string is 7A oriented as shown in the diagram . TERMINALS NOTE: If the auxiliary battery connector is in the way, remove its mounting screw and 7B position the cable to allow adequate room to add the battery strings . 7A 7B Slide the battery string with the BLACK cable next to it (on
ページ15に含まれる内容の要旨
240 Adding or Replacing Internal Batteries (continued) Connect the BLUE and WHITE jumper cables on each internal 10 10 battery pack to its corresponding fuse block. See printing next to fuse block to locate the correct fuse block for each cable. Insert the battery cartridge fuses into each fuse block. The fuses are 11 11 identical, and can be inserted into any of the blocks. Make sure that the fuses are firmly snapped into place. DANGER! BATTERY CARTRIDGE FUSES MUST BE INSERTED LAST DUE TO THE
ページ16に含まれる内容の要旨
Adding or Replacing Internal Batteries (continued) WARNING! OBSERVE PROPER POLARITY! Connect BLACK-to-BLACK and RED-to-RED. Failure to observe proper polarity will cause permanent damage to the UPS System and create a potential for serious personal injury. Connect the BLACK cable for each internal battery pack to the 13 13 / 14 nearest BLACK connector located inside the UPS system's battery module. Connect the RED cable for each internal battery pack to the nearest 14 RED connector located ins
ページ17に含まれる内容の要旨
Specifications Model: SU20K3/3 Model: SU20K3/3XR5 Input Input Input Voltage 120/208V AC, 3ø, 4 Wire (plus ground), wye Input Voltage 120/208V AC, 3ø, 4 Wire (plus ground), wye Input Frequency 60 Hz ± 3 Hz Input Frequency 60 Hz ± 3 Hz Voltage Correction Range 88-144/166-250V AC Voltage Correction Range 88-144/166-250V AC Input Current (Per Phase, On-Line) 60A Input Current (Per Phase, On-Line) 60A Inrush Current <300A Inrush Current <300A Power Factor (Full Load) >0.95 Power Factor (Full Load) >
ページ18に含まれる内容の要旨
Specifications (continued) Model: SU30K3/3XR5 Model: SU30K3/3 Input Input Input Voltage 120/208V AC, 3ø, 4 Wire (plus ground), wye Input Voltage 120/208V AC, 3ø, 4 Wire (plus ground), wye Input Frequency 60 Hz ± 3 Hz Input Frequency 60 Hz ± 3 Hz Voltage Correction Range 88-144/166-250V AC Voltage Correction Range 88-144/166-250V AC Input Current (Per Phase, On-Line) 90A Input Current (Per Phase, On-Line) 90A Inrush Current <300A Inrush Current <300A Power Factor (Full Load) >0.95 Power Factor
ページ19に含まれる内容の要旨
Manual del Propietario ™ Sistemas UPS SmartOnline Trifásicos de 20kVA y 30kVA Inteligente Genuino en Línea Voltaje de Entrada/Salida: 120/208V CA, 3ø, 4 hilos (más tierra), wye Advertencias de Seguridad Importantes 20 Panel Frontal 21 Panel Trasero 23 Instalación 24 25 Operación (Condiciones Normales) 26 Operación (Condiciones Especiales) 28 Comunicaciones Añadiendo o Remplazando Las Baterías Internas 29 Servicio 35 Garantía 35 Especificaciones 36 English 1 Français 38 1111 W. 35th Street � Chic
ページ20に含まれる内容の要旨
Advertencias de Seguridad Importantes GUARDE ESTAS INSTRUCCIONES. Este Manual contiene instrucciones y advertencias importantes que se deberán seguir durante la instalación y mantenimiento de todos los sistemas UPS SmartOnline Trifásicos de 20kVA y 30kVA de Tripp Lite. Advertencias sobre la colocación y ubicación del UPS • Instale su UPS en un ambiente controlado. • Instale su UPS en interiores, lejos del calor, luz solar directa, polvo y exceso de humedad y otros contaminantes conductivos. • In
