ページ1に含まれる内容の要旨
0905
Software Program to load Data into GF-NS/A Digital Display Module
- INSTRUCTIONS -
IMPORTANT! Read these instructions before loading or editing data in the GF-NS/A Digital Name
Scrolling Module for the GF series multi-unit entry system.
This software program allows you to use a computer to load the following information into the GF-NS/A.
Note that you will need to use a computer with a serial port along with the supplied connecting cable to plug
into the GF-NS/A. If only a USB connection
ページ2に含まれる内容の要旨
MAIN MENU: 1. Select Language: 2. New ID Code: Click radio button of language Enter * symbol, then new 4-digit to be used while programming. ID code. This is a security code and is required in order to make any changes to the GF-NS/A data via the keypad, or when exporting data into the unit. NOTE: To manually reset code from the GF-NS/A: Move SW1 to ON position for 2 seconds, then turn off again. This will reset 3. Change Access Code: code back to *1111. 4-digit Access Codes for users
ページ3に含まれる内容の要旨
MAIN MENU (Continued): 4. Resident Information: Program 3- or 4-digit Dialing Code (room number) and Resident Name (optional) Use Caps Lock while typing 0 ~ 9 only, 3 or 4 digits Capital A ~ Z , . / - only IMPORTANT!!! 1. This program allows you to use numeric dialing numbers to call each tenant location, either 3 or 4 digits in length. 2. The Resident Name field is optional. When entering into this field, the computer must be in “Caps Lock” mode. The program will not accept entry of lowe
ページ4に含まれる内容の要旨
MAIN MENU (Continued): 5. Set Timer: Operation Timer (15 to 99 seconds) Program Timer (30 to 99 seconds) 1. Enter the desired length of time in seconds for the operation timer. 2. Enter the desired length of time in seconds for the program timer. 3. Click OK. Operation Timer sets the length of time from when the last button is pressed on the keypad until the system resets to standby mode, displaying the scrolling welcome message. For example, if someone is scrolling through the names,
ページ5に含まれる内容の要旨
SUB MENU: 1. Open: Command to open a previously saved GF data file 1. When new information has not yet been entered into the program, a dialog box will appear. 2. Browse to the location on your computer where the .gfn files are saved. 3. Select the file name you wish to open. 4. Click “Open”. If data has been entered into the GF program but not saved yet, when you click “Open”, this dialog box will appear. 1. By clicking OK, you will lose any unsaved information you have entered. 2. Cli
ページ6に含まれる内容の要旨
SUB MENU (Continued): 4. Print: Command to print a hard copy of the information entered into the program. 1. This dialog box appears when clicking the “Print” button. Default elements to be printed are already checked. 2. If you wish to change any information to be printed, simply check or uncheck the appropriate box. 3. Click “Print”, and a hard copy of the programmed information will be printed. 4. Save the record with the job information for future reference. 5. Select COM Port: COM p
ページ7に含まれる内容の要旨
SUB MENU (Continued): 6. Export: Export Data to GF-NS/A IMPORTANT!!! 1. When exporting data from the computer into the GF-NS/A, it will REPLACE any program data already in the unit, whether it had been programmed manually via the keypad or exported previously from the computer. If the GF entrance panel has already been programmed to call the tenant stations, you must edit the ORIGINAL program data in the GF-NS/A. DO NOT REPLACE the original data with new data, as could cause the system to
