ページ1に含まれる内容の要旨
Users Manual
PORTABLE FILTER
MODELS PC14, LB-100, LB-65, LB-200
READ AND SAVE THIS MANUAL FOR FUTURE REFERENCE.
RECORD THE MODEL AND SERIAL SERIAL NO. ______________________________
NUMBERS OF THIS PORTABLE FILTER
MODEL NO. _____________________________
IN THE SPACES PROVIDED.
KEEP THESE NUMBERS FOR FUTURE REFERENCE.
IMPORTANT: Keep a copy of your bill of sale. The date on the bill establishes the warranty period should
service be required. If service is performed, it is in your interest to obt
ページ2に含まれる内容の要旨
PORTABLE FILTER OPERATING INSTRUCTIONS A. PREPARING THE PORTABLE FILTER 1. Remove screen from over tubes/element with tongs or a Drain Clean Out Rod (See Figure 1.1). SCREEN OVER TUBES/ ELEMENTS WILL BE VERY HOT AND SHOULD BE MOVED TO A SAFE PLACE. 2. Heat fryers to 325°F. Stir oil thoroughly until all water is removed and shut fryer off (including pilot light) before filtering. (Figure 1.2) NOTE: Water settles in the cooler oil in the Cold Zone. If the water is not Figure 1.1: Remove screen o
ページ3に含まれる内容の要旨
C. CLEAN-UP FILTER UNIT AND PIPES WILL REMAIN HOT FOLLOWING FILTRATION. ALLOW THE UNIT TO COOL DOWN BEFORE CLEAN UP. FAILURE TO DO SO MAY RESULT IN SERIOUS INJURY TO THE OPERATOR. 1. Turn off filter and disconnect from electrical source. 2. Remove strainer basket and hold down ring for cleaning 3. Remove and discard filter paper and any residue. Figure 2.1: Drain fryer 4. Clean filter tub thoroughly. 5. Coat inside of pump with oil if water has been running through it. 6. Place hose so that rema
ページ4に含まれる内容の要旨
SELF-HELP GUIDE PROBLEM PROBABLE CAUSE SOLUTION (Follow Sequentially) Motor runs but will not pump oil. A. Solidified shortening may have Turn on fat melter for 20 minutes. This will heat plugged pipes. filter tub and pipes to free system of solidified shortening. Reset motor before attempting filtering (reset button is located on rear of pump motor). B. Tub not set up properly. Place components in tub per the following: 1. Filter screen on the very bottom. 2. Filter paper over filter screen (Li
ページ5に含まれる内容の要旨
SERVICE Replacement: DISASSEMBLY 1. Connect tagged electrical leads to replacement You will need: switch. Adjustable wrench “Stubby” screwdriver Standard pliers Standard screwdriver 2. Insert replacement switch through panel from which defective switch was removed. Insert nameplate over Servicing should only be performed by qualified and licensed toggle and secure to panel with nut supplied with service companies. Always disconnect the electrical power switch. Orient switch and tighten nut to se
ページ6に含まれる内容の要旨
SERVICE (continued) 4. Remove attaching screws securing front panel. Tilt D. HEATER ELEMENT(S) back front panel to expose pump and motor. Removal: 5. Remove motor junction box cover and remove 1. Disconnect filter from electrical power source. electrical leads from motor terminals. Tag leads as they are disconnected to assure, during replacement, NOTE: Remove all oil from filter vessel. Filter must they are reconnected to proper terminals. be positioned on its end to access heater element(s).
ページ7に含まれる内容の要旨
SERVICE (continued) F. HEAT TAPE Removal: 1. Disconnect filter from electrical power source. NOTE: Remove all oil from filter vessel. Filter must be positioned on its end to access heat tape. 2. Raise front (power cord) end of filter and rest filter on oil absorbing rags on its back end. 3. Remove bottom cover attaching screws; remove bottom cover. 4. Sketch course defective heat tape follows to assure oil and various components can be sufficiently heated during filter operation preventing any
ページ8に含まれる内容の要旨
PORTABLE FILTER PARTS LIST ORDERING PARTS Parts - LB100 Model Parts may be ordered by part number by calling your local Caster 3” swivel 000626 service company or Keating at 1-800-KEATING. You may Caster 3” rigid 000627 also order on-line at Keating’s part store, Cover for LB-100 (2000 series) 056273 www.keatingofchicago.com. Cover for LB-100 (optional) (pre 2000 series) 000503 Filter screen LB-100 12 1/4” diameter 000591 Refer to the Keating Filter Limited Warranty for warranty Indicating Light
ページ9に含まれる内容の要旨
PORTABLE FILTER PARTS LIST Parts - LB165 Model (continued) Strainer Basket LB165 000677 Switch (Pump-off-melt) 000521 Switch Reversing (2-Way Pump) 000527 Terminal Block 002065 Terminal Board 000639 Terminal Board Insulation 000263 Parts - LB200 Model Caster 3” swivel 000626 Cover for LB200 056258 Handle for cover 004542 Heat Plate 500W 115V 000596 Heat Wrap Wire 4 ft. 100W 120V 012055 Hi-Limit Sensor 000694 Hold Down Ring (after 2004) 053033 Hold Down Ring (pre 2000) 016121 Hold Down Ring (pre
ページ10に含まれる内容の要旨
LB100, LB165, LB200 1 Way Pump - Part # 008196 LB100, LB165, & LB200 2 Way Pump - Pump Part # 055173 (1988 - 2002) 9
ページ11に含まれる内容の要旨
LB165 & LB200 1 Way Pump (model 2004 series) - Pump Part # 055173 LB165 & LB200 1 Way Pump (after 2005) - Pump Part # 055173 WIRE # 3, GR WIRE # 3, GR W WH H W WH H 7 6 WH WH 1133 1 B BLL 5 H HTT HT HT 4 B BU U 8 BU BU WH WH 9 2 BU BU BU BU RESET SWITCH RESET SWITCH W WH H 1111 IV CONTROL PANEL INSERT CONTROL PANEL INSERT MOTOR MOTOR FILTER FILTER PUMP PUMP LEGEND: LEGEND: BL BL— BLACK BLACK BU BU— BLUE BLUE WH WH— WHITE WHITE GR GR—GREEN GREEN HT HT— HEAT TAPE WRAP HEAT TAPE WRAP 10 P P11 TT11
ページ12に含まれる内容の要旨
LB165 & LB200 1 Way Pump (model 2003 series) - Pump Part # 052982 LB165 & LB200 2 Way Pump - Pump (after 2004) - Pump Part # 055173 11
ページ13に含まれる内容の要旨
LB200 1 Way Pump - Pump Part # 010567 (1993) LB200 2 Way Pump - Pump Part # 010567 (1993) 12
ページ14に含まれる内容の要旨
PC14 13
ページ15に含まれる内容の要旨
ページ16に含まれる内容の要旨
SERVICE INFORMATION If you have a service related question call 1-800-KEATING. Please state the nature of the call; it will ensure speaking with the appropriate person. Have your serial and model number available when ordering parts. KEATING OF CHICAGO, INC. 8901 West 50th Street, McCook, Illinois 60525-6001 Phone: (708) 246-3000 FAX: (708) 246-3100 Toll Free 1-800-KEATING (In U.S. and Canada) www.keatingofchicago.com *As continuous product improvement occurs, specifications may be changed wit
