ページ1に含まれる内容の要旨
www.zephyronline.com
Willow
AK8800AS
AK8800AG
INTENDED FOR OUTDOOR COVERED PATIO OR LANAI AREA.
Model number:
Serial Number:
Date of Purchase:
Sales Dealer:
AUG08.0101 © 2008 Zephyr Corporation
READ AND SAVE THESE INSTRUCTIONS
Use, Care, and Installation Guide
ページ2に含まれる内容の要旨
www.zephyronline.com
ページ3に含まれる内容の要旨
SAFETY NOTICE ................................................................. 2-3 LIST OF MATERIALS ....................................................... 4 INSTALLATION Ducting Calculation Sheet ....................................... 5 Mounting Height & Clearance ................................ 6 Ducting Options ........................................................... 7 Specifi cations ............................................................... 8 Electrical ..........................
ページ4に含まれる内容の要旨
READ AND SAVE THESE INSTRUCTIONS www.zephyronline.com WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID-STATE CONTROL DEVICE. WARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: a. Use this unit only in the manner intended by the manufacturer, if you have questions, contact the manufacturer. b. Before servicing or cleaning unit, switch power off at service panel and lock panel to prevent power from being swit
ページ5に含まれる内容の要旨
CAUTION To reduce risk of fi re and to properly exhaust air outside - Do not vent exhaust air into spaces within walls, ceilings, attics, crawl spaces or garages. OPERATION Always leave safety grilles and fi lters in place. Without these components, operating blowers could catch onto hair, fi ngers and loose clothing. The manufacturer declines all responsibility in the event of failure to observe the instructions given here for installation, maintenance and suitable use of the product. Th
ページ6に含まれる内容の要旨
www.zephyronline.com MODELS: AK8800AS AND AK8800AG PARTS SUPPLIED 1 - 316S High quality stainless steel Power Pack (AK8800AS) or 1 - Gray powder coated Power Pack (AK8800AG) 2 - Baffl e fi lters 2 - Halogen light bulbs (pre-installed) 1 - Dual internal blower (pre-installed) 1 - 8” round adapter 1 - Hardware package Suction Cup (1) M4 x 1” (6) M4 x 8 (4) Wire Caps (3) HARDWARE PACKAGE CONTENTS PARTS NOT SUPPLIED - Ducting, conduit and all installation tools - Cable connector (if required by loca
ページ7に含まれる内容の要旨
Equivalent number Duct pieces Equivalent number Duct pieces length x used = Tota l length x used = Tota l 3-1/ 4” x 10” 1 Ft. x ( ) = Ft. Ft. 6” Round 30 Ft. x ( ) = Rect., wall cap straight with damper 6” Round, 1 Ft. x ( ) = Ft. 6” Round, Ft. 30 Ft. x ( ) = straight roof cap 7”-10” Round, 1 Ft. x ( ) = Ft. Ft. 6” round to 1 Ft. x ( ) = straight 3-1/ 4” x 10” rect. transition Ft. 3-1/ 4” x 10” 15 Ft. x ( ) = 6”
ページ8に含まれる内容の要旨
www.zephyronline.com Minimum mount height between range top to hood bottom should be no less than 30”. Maximum mount height should be no higher than 36”. It is important to install the hood at the proper mounting height. Hoods mounted too low could result in heat damage and fi re hazard; while hoods mounted too high will be hard to reach and will lose its performance and effi ciency. If available, also refer range manufacturer’s height Min 30" - Max 36" clearance requirements and recommend
ページ9に含まれる内容の要旨
WARNING FIRE HAZARD NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages. All exhaust must be ducted to the outside. Use metal ductwork only. Fasten all connections with sheet metal screws and tape all joints with certifi ed Silver Tape or Duct Tape. Some Ducting Options side wall cap side wall cap w/ gravity damper w/ gravity damper Soffit or crawl space Roof Pitch w/ Flashing & Cap 7 Installation – Ducting Options
ページ10に含まれる内容の要旨
www.zephyronline.com 316 High Class Stainless Steel Body for AK8800AS 11 7/16” C 1 3/4” L elec 1 1/2” 14 11/16” k/o C L 11 7/16” 6 1/2” 13/16” elec. 15 13/16” k/o 1 1/2” 1 5/16” 2 5/8” 14 11/16” 15 13/16” top side 24 5/8” 14 3/4” 7 3/4” 5” 11 7/16” 4 3/8” 4 3/4” 2 3/8” 25 15/16” 29 13/16” front 8 Installation – Specifi cations
ページ11に含まれる内容の要旨
ELECTRICAL WARNING All Electrical work must be performed by qualifi ed electrician or person with similar technical know how and background. For personal safety, remove house fuse or open circuit breaker before beginning installation. Do not use extension cord or adapter plug with this appliance. Follow national electrical codes or prevailing local codes and ordinances. Electrical Supply: This appliance requires a 120V 60Hz electrical supply, and connected to an individual, properly grounded b
ページ12に含まれる内容の要旨
www.zephyronline.com ! CAUTION: At least two installers are required due to the weight and size of the hood. Remove support screw from top of Power Pack AK8800Ax before installing into cabinet. FIG 2b 26 1/16” C/L 1. Place 8” round adapter on top of power pack and secure with (4) M4x8 screws. (FIG 3) C/L 2. Install optional AK088xAS Stainless Steel Liner under custom hood opening. Review manual included with liner for more details. 3. If no liner is used cut out an opening in
ページ13に含まれる内容の要旨
1 Lights On/Off 2 Adjust Blower Level (2 Speeds) 1 Light On/Off By pressing , the light is switched On and Off. is on, is off. 2 Blower Speed Selection The 2 speed levels are selected by switching to for level one and for level two. Switching the rocker switch to middle will turn off the blower. 11 Controls – Rocker Switch Controls
ページ14に含まれる内容の要旨
www.zephyronline.com ! CAUTION: If this hood is installed in a salt water area (example: coast), rinse all surfaces once a week with clear water (even if the hood is not used), and wipe dry completely. SURFACE MAINTENANCE: Clean periodically with hot soapy water and clean cotton cloth. Do not use corrosive or abrasive detergent, or steel wool/ scoring pads which will scratch and damage surface. Do not use products containing chlorine bleach or orange cleaners. For heavier soil use liquid degr
ページ15に含まれる内容の要旨
REPLACING LIGHT BULBS CAUTION: Light bulb becomes extremely hot when turned on. DO NOT touch bulb until switched off and cooled. Touching hot bulbs could cause serious burns. Make sure all power is turned off and bulbs are not hot. Remove by turning bulb counter clockwise. Note: Bulb does not unscrew; it turns 60 degrees, stops and falls out. If bulbs are diffi cult to turn due to prolonged use, fi rmly attach a glass suction cup approximately the diameter of the bulb or use a rubber/latex glove
ページ16に含まれる内容の要旨
www.zephyronline.com TROUBLESHOOTING PROCEDURES FOR WILLOW Issue Cause What to do After installation, 1. The power source is not turned ON. 1. Make sure the circuit breaker and the unit’s the unit doesn’t power is ON. work. 2. The power line and the cable locking connector 2. Check the power connection with the unit is is not connecting properly. connected properly. 3. The switch board and control board wirings are 3. Make sure the wirings between the switch disconnected. board and control bo
ページ17に含まれる内容の要旨
DESCRIPTION PART # Replacement Parts Light Bulb MR16 (GU10) 35W (each) Z0B-0023 Baffl e Filter (each) 50210010 Optional Accessories Liner, 36” AK0886AS Liner, 42” AK0882AS Liner, 48” AK0888AS Liner, 54” AK0884AS Liner, 60” AK0880AS To order parts, visit us online at http://store.zephyronline.com or call us at 1.888.880.8368 15 List of Part
