ページ1に含まれる内容の要旨
V.
If
I
A
1. A
2.
duct duct
of roof
ior indoor
most of hood
66 (167.6 cm) from floor.
/-T
/
; l
1
J
or for
‘,-/
29
/
T
l (to hood
to hood
l ffor
l for
l or for or
l
if or roof
l-30-84 1 Page A626-168/883029
required.
as cap, cap wall and necessary) transitron.
and elbow (with ducts tape, duct snips, metal Caulking,
openings.
cabinet wall the cutting saw keyhole saw Saber
locations. cabinet marking level and ruler Pencil,
knockouts). opening Pliers
parts).
met
ページ2に含まれる内容の要旨
1. a or 3 to or 2. to W’ (.6 cm) on four for J/4” (1.9 cm) front for (.6 cm) on for 3. for 4. or to turn on 5. for on 6. 6. 7. 3. 1 8. If 9. 5 for x or 6 for 10. Lift hood of four 11. hood four of of on 12. Lift hood for to 13. to hood. of 14. 4 15. to 2 16. 17. different 5 for 6 for 3 for 18. It found a of of to or 19. 1 8 2). 6 5 4 2 Page FIGURE FIG&E FIGURE c5mf 6-1 Figures (See installed. properly is model this with supplied is which damper
ページ3に含まれる内容の要旨
BLOWER duct duct BLOWER - OF maximum ,,/ 7 1, 7 2. 7. mounting 3. BLOWER - 1. 8 2. 8. 3. will 8 3 Page DISCHARGE HORIZONTAL FIGURE top.) the to be will surface 5” wider (the vent. rear the through Blower This hood. of rear against the from flow air proper allow flush be now’ should surface drscharge Blower 3” The position into vertrcally Assembly blower the lift Figure in shown position Blower the From discharge. horizontal for orientation Assembly Blower proper the
ページ4に含まれる内容の要旨
An 410 a a In thus duct must a maximum 2 x 10 duct a a 66 duct duct A x 10 duct. 4S0 I 3 x 10 duct In a In 3 x 10 duct maximum x 10 duct duct In 9 9 45O 113 In2 duct 45O duct In 2 I maxrmum duct 9 duct, 1 In a a 113 9 6 4S0 2 15 maximum 13 duct, duct duct 12 9 14 7 duct 45O 900 16 16 maximum 25 duct, duct a .25 355 26 61 104 .275 330 34 73 145 .30 250 65 136 .35 180 140 duct 4 Page caps. ram mounted roof through loss pressure static for account not do
ページ5に含まれる内容の要旨
time 3. time bulb 60 a mild 5 Page pads. ~001 steel soapy or cleansers abrasive use not Do cloth, soft detergent-and with hood range the Clean SURFACES: EXTERIOR water. sudsy hot in washed or dishwasher the in placed be may filter The often. clean and remove results, best For FILTER: Watts than larger use not Do LIGHT: pad “OFF” the Touch OFF: FAN TURN TO operation. during anytime decreased or increased be may Speed speed. highest its to increase will speed the pressed, de- con
ページ6に含まれる内容の要旨
BLOWER BLOWER 10 SCREW service result little things find , a natjon- rnd kind. I I * the in the in call number in under: number. . . (6W) 253-1301 (6W) 632-2243 (6W)253-1121 and talk nstruct in if a in number and talk if Guy must call number, number, and a the in 6 Page assistance for request your to respond better to order needed is informatlon This problem. of description complete purchase, of date serial model provide please write, or you If 49022 Ml Harbor,
ページ7に含まれる内容の要旨
1. 2. I 3. P. 4. b. nut P. nut d. P. 5. With 72 b. plug bulb -, \ .y FIG. 1 OF (1) 1-11-64 A626-476 HOOD INSIDE (2) SCREWS RETAINING COVER (4) TABS RETAINING FILTER -J (41, SCREWS RETAINING TRIM (2), SCREWS MTG COVER CONNECTOR PIN FIVE ENCLOSURE BOARD CIRCUIT 2.) Page (See switch. membrane or board circuit the in is problem correct, not are outputs If C. motor.) fan defective and/or or socket (Bad themselves. devices the in or light) and (fan devices to from wiring th
ページ8に含まれる内容の要旨
6. b. up d. a P. P. b. trim trim trim. a d. trim, /- MfG FIG. 2 P C REMOVAL BOARD CONNECTOR PIN FIVE SCREWS@) BOARD PC cover. enclosure board circuit and board, circuit original replace properly, works it if and unit Operate f. tab. locking with secure and connector board circuit into tail flex Insert e. switch. of off peeling carefully by coating protective front switch Remove panel. front to switch secure to adhesive allowing before switch aligning CAREFULLY and slot front
