ページ1に含まれる内容の要旨
�
�
�
�
�
�
�
�
�
Direct Vent Model:
DVR28IN
� � � � � � � � �
Installation Instructions and Homeowner’s Manual
INSTALLER/CONSUMER SAFETY INFORMATION
PLEASE READ THIS MANUAL BEFORE INSTALLING AND USING APPLIANCE
�����
WARNING!
� ������ � � ��
IF THE INFORMATION IN THIS MANUAL IS NOT
����
FOLLOWED EXACTLY, A FIRE OR EXPLOSION MAY
RESULT CAUSING PROPERTY DAMAGE, PERSONAL
INJURY OR LOSS OF LIFE.
WHAT TO DO IF YOU SMELL GAS: FOR YOUR SAFETY
• Do not try to light any appliance.
Installation and
ページ2に含まれる内容の要旨
Vermont Castings DVR28 Direct Vent Gas Fireplace Table of Contents PLEASE READ THE INSTALLATION & OPERATING INSTRUCTIONS BEFORE USING APPLIANCE. Thank you and congratulations on your purchase of a CFM Corporation fireplace. IMPORTANT: Read all instructions and warnings carefully before starting installation. Failure to follow these instructions fully may result in a possible fire hazard and will void the warranty. Installation & Operating Instructions Important Curing/Burning Instructions ...
ページ3に含まれる内容の要旨
Vermont Castings DVR28 Direct Vent Gas Fireplace Installation & Operating Instructions This gas appliance must be installed by a qualified 13. This fireplace must not be connected to a chimney installer, preferably NFI or WETT (Canada) certified, flue serving a separate solid fuel burning fireplace. in accordance with local building codes and with 14. When the fireplace is not in use it is recommended current CSA-B149.1 Installation codes for Gas Burning that the gas valve be left in the OFF pos
ページ4に含まれる内容の要旨
Vermont Castings DVR28 Direct Vent Gas Fireplace DVR28 Fireplace Dimensions Finished Wall 6���” 1“ (25 mm) Min. (162 mm) 19���” 15����" (492 mm) (395 mm) 14�����” (377 mm) 28” (711 mm) 12” (305 mm) Finished Wall Min. Fig. 1 Fireplace specifications and framing dimensions. Minimum Ceiling and Side View Typ. 16” (406 mm) o.c.* Floor Clearance 24” Ceiling (610 mm) 27” Min. Finished Wall (686 mm) 12301 DVR28 specs 3/07 Top of Unit 10��� ” (264 mm) NOTE: Minimum 9��� ” clearances are with 1“ (238
ページ5に含まれる内容の要旨
Vermont Castings DVR28 Direct Vent Gas Fireplace 3. Make sure framing for firestop is correct. NOTE: Locating Your Fireplace Firestop is for combustible walls. Refer to firestop framing instructions on Pages 4 and 12, Figures 4 and 17. 4. Plumb for gas connection. Refer to Gas Line Instal- E A B Y lation on Page 6. X 5. Finish wall as desired. C CAUTION: If wall is finished with combustible D materials, be sure to install firestop according Y B to instructions. F Mounting the Fireplace LU584-R
ページ6に含まれる内容の要旨
Vermont Castings DVR28 Direct Vent Gas Fireplace Sheet Metal Gas Line Installation Screws (8) When purging the gas lines, the front win- dow frame assembly must be removed. The gas pipeline can be brought in under the bottom of the fireplace. The gas line connections will be covered by bottom trim. Refer to Figure 7 for gas line dimen- sions. Use 1/2” rigid pipe. When gas line is in place un- Wall Mounting Bracket Secured to Walll der the fireplace, install supplied 1/2” FPT to 3/8” flare bras
ページ7に含まれる内容の要旨
Vermont Castings DVR28 Direct Vent Gas Fireplace White Wireless Remote Green Orange ON OFF HI/LO DC Pilot Module Motor Drive HI AF-4000 LO Main No wiring required. Red Orange (Refer to Pages 6,19, 23) FP1796 AF-4000B/P Black Red Wireless remote Brown 3/07 Black Red Black Gnd Black HI/LO DC Battery Pack Brown (SWI) Brown (SWI) Black Optional DC Red Battery Back-up FP1750 Fig. 8 DVR28 wiring diagram. Flue Diverter Restrictor Plate Installation The DVR28IN is shipped with a restrictor plate for e
ページ8に含まれる内容の要旨
Vermont Castings DVR28 Direct Vent Gas Fireplace General Venting There must not be any obstruction such as bushes, Your fireplace is approved to be vented either through garden sheds, fences, decks or utility buildings within the side wall, or vertically through the roof. 24” (610 mm) from the front of the termination hood. • Only CFM Corporation venting components specifi- Do not locate termination hood where excessive snow cally approved and labelled for this fireplace may be or ice build up
ページ9に含まれる内容の要旨
V Operable Vermont Castings DVR28 Direct Vent Gas Fireplace General Venting Information - Termination Location INSIDE CORNER DETAIL G V N H N A D E L C B ����� B V B V ������ V Fixed Operable Closed F V B M V B J X B I V K X A CFM145a AREA WHERE TERMINAL IS NOT PERMITTED V VENT TERMINATION X AIR SUPPLY INLET 1 2 Canadian Installations US Installations CFM145a A = Clearance above grade, veranda, porch, 12” (30 cm) 12” (30 cm) DV Termin Location deck, or balcony 5/01/01 Rev. 12/05/01 sta
ページ10に含まれる内容の要旨
Vermont Castings DVR28 Direct Vent Gas Fireplace Termination Clearances Termination clearances for buildings with combustible and noncombustible exteriors. Inside Corner Alcove Applications* Outside Corner D C C F = Combustible G = 6" (152 mm) Combustible V G 6" (152 mm) Noncombustible V E 2" (51 mm) Noncombustible O V F 2" (51 mm) Balcony - Balcony - with no side wall with perpendicular side wall E = Min. 6” (152 mm) for non-vinyl sidewalls Min. 12” (305 mm) for vinyl sidewalls
ページ11に含まれる内容の要旨
Vertical dimension from the floor of the unit to the center of the horizontal vent pipe Vermont Castings DVR28 Direct Vent Gas Fireplace How to Use the Vent Graph Rear Wall Venting Applications The vent chart should be read in conjunction with the When installed as a rear vent unit this appliance may following vent installation instructions to determine the be vented directly to a termination located on the rear relationship of the vertical and horizontal dimensions of wall behind the appliance
ページ12に含まれる内容の要旨
Vermont Castings DVR28 Direct Vent Gas Fireplace Rear Wall Installation Adjustable Max. Length 12” (305mm) Zero Clearance Twist Lock Pipe Sleeve #8 Screws (2) STEP 1 Locate vent opening on the wall. To locate hole center consult with appropriate fireplace dimensions, Page 4. #8 Screws (2) Frame as shown below. #8 Screws (2) Combustible Walls (Fig. 17): Cut a 10 ³⁄₈”H x 9 ³⁄₈” W (264 x 240 mm) hole through the exterior wall and Firestop frame as shown. Noncombustible Walls (Fig. 17): Hole
ページ13に含まれる内容の要旨
Vermont Castings DVR28 Direct Vent Gas Fireplace Example: According to the vent graph (Page 11) the Vertical Sidewall Applications maximum horizontal vent length in a system with a 7.5’ (2.3 m) vertical rise is 20’ (6 m) and if a 90° elbow is Since it is very important for the venting system required in the horizontal vent it must be reduced to 17’ to maintain balance between the combustion air (5.2 m). In Figure 21 Dimension A plus B must not be intake and the flue gas exhaust, certain l
ページ14に含まれる内容の要旨
Vermont Castings DVR28 Direct Vent Gas Fireplace Do not backfill around snorkel. Below Grade Installations A clearance of at lest 4” must be main- When it is not possible to meet the required vent ter- tained between the snorkel and the soil. minal clearances of 12” (305 mm) above grade level If the foundation is recessed, use recess brackets (not a snorkel kit is recommended. This allows installation supplied) for securing lower portion of the snorkel. Fas- depth of down to 7” (178 mm) belo
ページ15に含まれる内容の要旨
Vermont Castings DVR28 Direct Vent Gas Fireplace If there is a room above ceiling level, fire stop spacer • A minimum of an 8’ (2.5m) vertical rise is required. must be installed on both the bottom ad the top side • Two sets of 45° elbow offsets may be used within the of the ceiling joists. If an attic is above ceiling level a vertical sections. From 0 to a maximum of 8’ (2.5 m) 7DVAIS (Attic Insulation Shield) must be installed. of vent pipe can be used between elbows. (Fig. 26) The enlarge
ページ16に含まれる内容の要旨
Vermont Castings DVR28 Direct Vent Gas Fireplace Min. 2' (610 mm) 3 #5 Sheet Metal Screws per Joint Sealant Storm Collar TWL101a Fig. 30 Roof flashing. TWL101a FP1185 Twist Lock Pipe 2/8/99 djt Fig. 29 Minimum termination to roof clearance. 20012301 16
ページ17に含まれる内容の要旨
Vermont Castings DVR28 Direct Vent Gas Fireplace Venting Components 7TDVRVT - Through the wall Rear Vent Termination 584A Starter Kit - venting components rear vent term Model 7TDVSK - Sidewall Venting (Twist Lock Pipe) 4/6/99 djt Model 7FDVSK - Sidewall Venting (Flex Vent Pipe) Models 7TDVTK/TV - Hot Touch Termination Kits Model 7TDVTVTK/TV - Cool Touch Termination Kit Starter Kit - Model 7TDVSKV - Vertical Venting for 7TDVSKV-A order 1/12 to 6/12 roof pitch for 7TDVSKV-B order 7/12
ページ18に含まれる内容の要旨
Vermont Castings DVR28 Direct Vent Gas Fireplace Operating Instructions Glass Cleaning Glass Information It is necessary to clean the glass periodically. During Only glass approved by CFM Corporation start-up condensation, which is normal, forms on the should be used on this fireplace. inside of the glass and causes lint, dust and other • The use of any non-approved replacement glass will airborne particles to cling to the glass surface. Also void all product warranties. initial paint curi
ページ19に含まれる内容の要旨
Vermont Castings DVR28 Direct Vent Gas Fireplace Flame & Temperature Adjustment To adjust Hi/Lo setting, push either the high or low con- trol button on remote control transmitter. ON OFF HI LO LG480 Fig. 35 Correct DVR28 flame. Center flame should be ap- proximately 5 ¹⁄₂” (140 mm) high. FP1759 FP1796 Fig. 33 Flame adjustment for American Flame valve. Wireless remote Inspecting the Venting System 3/07 Flame Characteristics � ������ ���������� This appliance venting system is designed and con- I
ページ20に含まれる内容の要旨
Vermont Castings DVR28 Direct Vent Gas Fireplace Lighting & Operating Instructions For Fireplaces equipped with AF4000 Gas Valve Warning: If you do not follow these instructions exactly, a fire or explosion may result, causing property damage, personal injury and loss of life. For Your Safety, Read the Following Warnings before Lighting the Appliance • Immediately call your gas supplier from A. This fireplace is equipped with an ignition device a neighbor’s phone. Follow
