ページ1に含まれる内容の要旨
LEIHDS120SC/
Users Guide
&
Installation Instructions
ページ2に含まれる内容の要旨
CONTENTS IMPORTANT SAFETY INFORMATION Installation Page 2 Child Safety 2 Maintenance and service 3 YOUR APPLIANCE OPERATING INSTRUCTIONS Cooker Hood Controls 4 To Operate 5 Recirculation 5 Extraction 5 MAINTENANCE AND CLEANING Metal Grease Filters 6 Charcoal Filter 6 Lighting 7 Cleaning 7 INSTALLATION INSTRUCTIONS Technical Information 8 ELECTRICAL CONNECTION Elecrical Requirements 9 Electrical Connection 9 INSTALLING THE CHIMNEY HOOD Components 10
ページ3に含まれる内容の要旨
IMPORTANT SAFETY INFORMATION These warnings are provided in the interests of safety. Ensure that you understand them all before installing or using this appliance. Your safety is of paramount importance. If you are unsure about the meaning of any of these warnings contact the Helpline. • If the room where the cooker hood is to • INSTALLATION be used contains a fuel burning appliance • Any installation work must be such as a central heating boiler then its undertaken by a qualified electrician or
ページ4に含まれる内容の要旨
IMPORTANT SAFETY INFORMATION • MAINTENANCE AND SERVICE • This appliance can be a hazard if the grease filters and charcoal filters are not cleaned and replaced as recommended. • Always insist on genuine RANGEmaster spare parts. • Under no circumstances should you attempt to repair the appliance yourself. Repairs carried out by inexperienced persons may cause injury or more serious malfunction. In the event of your chimney hood requiring service contact: RANGEmaster Helpline: 0845 603 5312, or Co
ページ5に含まれる内容の要旨
YOUR APPLIANCE OPERATING INSTRUCTIONS The chimney hood is designed to extract BUTTON V1 - Turns the fan On and Off at unpleasant odours from the kitchen, it will the low speed setting. This is not extract steam. The appliance can be an ideal speed when cooking installed to recirculate or extract for long periods as the continuous flow of air is contaminated air. particularly quiet. COOKER HOOD CONTROLS BUTTON V2 - Medium speed, suitable for The chimney hood functions are controlled most normal o
ページ6に含まれる内容の要旨
OPERATING INSTRUCTIONS TO OPERATE Select the required fan speed and light if required. To obtain the best performance when cooking it is advisable to switch the chimney hood on for a few minutes before you start cooking and leave it running for about 15 minutes after finishing. RECIRCULATION In the recirculation mode contaminated air enters the chimney hood through the grease filter cassettes. The air is cleaned as it passes through the charcoal filter and is passed out through grilles in either
ページ7に含まれる内容の要旨
MAINTENANCE AND CLEANING Regular maintenance and cleaning will ensure good performance and reliability, while extending the working life of the hood. Special attention should be paid to the grease filter cassettes and the charcoal filter when the hood is used in the recirculation mode. Before carrying out any mainte- THIS APPLIANCE CAN BE A nance or cleaning isolate the cooker hood POSSIBLE FIRE HAZARD IF THE GREASE FILTERS ARE NOT CLEANED AND THE from the mains supply. CHARCOAL FILTERS REPLACED
ページ8に含まれる内容の要旨
MAINTENANCE AND CLEANING LIGHTING The canopy is fitted with three 20W halogen spotlamps. If one of the spotlamps fails to function check that the two pins are correctly inserted into the lamp holder. To replace a spotlamp remove the two screws, which secure the lens retaining ring and glass lens as illustrated. Take care to ensure the lens and retaining ring are supported while removing the screws. Extract the spotlamp from the lamp holder by pulling gently. Replacement spotlamps are specified 2
ページ9に含まれる内容の要旨
INSTALLATION INSTRUCTIONS It is dangerous to alter the specifications or attempt to modify this chimney hood in any way. TECHNICAL INFORMATION DIMENSIONS CANOPY: Height 60mm Width 1198mm Depth 490mm CHIMNEY: Height - Upper Chimney 215mm Lower Chimney 740mm Width 300mm Depth 260mm ELECTRICAL SUPPLY VOLTAGE: ~50Hz 230V POWER CONSUMPTION: 200W FAN: 140W SPOTLAMPS: 3x20W 60W PERFORMANCE SPEEDS 3 3 C
ページ10に含まれる内容の要旨
ELECTRICAL CONNECTION THIS APPLIANCE MUST BE EARTHED ELECTRICAL REQUIREMENTS Any permanent electrical installation must comply with the latest I.E.E. Regulations and local Electricity Board regulations. For your own safety this should be undertaken by a qualified electrician e.g. your local Electricity Board, or a contractor who is on the roll of the National Inspection Council for Electrical Installation Contracting (NICEIC). ELECTRICAL CONNECTION Before connecting to the mains supply ensure t
ページ11に含まれる内容の要旨
INSTALLING THE CHIMNEY HOOD COMPONENTS The chimney hood comprises of the following: - No 1 150x120mm ducting spigot (A) No 1 120x125mm ducting flange (B) No 1 Canopy (C) No 2 Recirculation grilles (G) No 1 Lower chimney stack (I) No 1 Recirculation ducting (P) No 2 Recirculation extension ducts (P1) No 1 Recirculation spigot (R) No 1 Upper chimney stack (S) No 1 Valve (V) optional No 2 Chimney fixing brackets (2) Please ensure when the appliance is fitted it is easily accessible to an engineer i
ページ12に含まれる内容の要旨
INSTALLING THE CHIMNEY HOOD CLEARANCE HEIGHTS The chimney hood is designed to be fitted over a cooking appliance. A minimum clear- ance height of 650mm (25˚ins) is required when installed above a built-in electric hob, or 700mm (27˚ins) when installed above a built-in gas hob. When installed between adjoining wall cabi- nets, the wall cabinets must not overhang the hob and the distance between the underside of the cabinet and worktop must be 450mm (17˚ins), and a gap of 50mm (2ins) must be maint
ページ13に含まれる内容の要旨
INSTALLING THE CHIMNEY HOOD 4. Drill the holes for the fixing screws 5. When the electrical connection has using an 8mm masonry drill bit. Insert been made, test the three speed fan the rawl plugs and fix the brackets (2) and the spotlams using the 4.2 x 44.4mm screws provided. DRILLING THE HOLES 1 1. Draw a horizontal line through the vertical 970mm up the wall from the top of the cooking appliance, ensuring it is level with a spirit level. 2. Mark the centres for the holes 1, 116mm either side
ページ14に含まれる内容の要旨
INSTALLING THE CHIMNEY HOOD DUCTING The hood is more effective when used in the extraction mode (ducted to the outside). When used in the extraction mode ensure the ducting spigot has been correctly fitted as illustrated. The ducting used must be Æ Æ Æ125 Æ Æ (5ins) or Æ Æ Æ150mm (6ins), flexible or Æ Æ rigid and must be manufactured from fire retardant material, produced to BS.476 or DIN.4102- B1. The choice should be made by the installer. However, we recommend flexible ducting should only be
ページ15に含まれる内容の要旨
INSTALLING THE CHIMNEY HOOD by pressing it downwards until the two pieces meet. 3. Connect the two recirculation extension ducting pipes P1 on to the outlets on either side of the spigot R, which push fit into position, by pressing them horzontally until the two pieces meet. 4. Do not fit the recirculation grilles until after the chimney has been installed. FITTING THE TELESCOPIC CHIMNEY The chimney stack consists of two sections. 1. To fit the upper chimney section S, first apply pressure to ex
ページ16に含まれる内容の要旨
4329643 03 020412
