ページ1に含まれる内容の要旨
INSTALLATION INSTRUCTIONS
HB0026
NP60000 SERIES
! !
INTENDED FOR DOMESTIC COOKING ONLY
READ AND SAVE THESE INSTRUCTIONS
INSTALLER: LEAVE THIS MANUAL TO HOMEOWNER.
HOMEOWNER: USE AND CARE INFORMATION ON PAGE 11.
NuTone Inc., 4820 Red Bank Road, Cincinnati, OH 45227 (1-800-543-8687)
www.nutone.com
V7450 rev. A
ページ2に含まれる内容の要旨
! ! WARNING WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC TO REDUCE THE RISK OF INJURY TO PERSONS SHOCK OR INJURY TO PERSONS, OBSERVE IN THE EVENT OF A RANGE TOP GREASE THE FOLLOWING: FIRE, OBSERVE THE FOLLOWING*: 1. Use this unit only in the manner intended by the 1. SMOTHER FLAMES with a close-fitting lid, cookie manufacturer. If you have questions, contact the sheet or metal tray, then turn off the burner. manufacturer at the address or telephone number BE CAREFUL TO PREVENT BURNS. IF THE l
ページ3に含まれる内容の要旨
TABLE OF CONTENTS 1. SELECT BLOWER OPTION AND INSTALL DUCTWORK............................................................................6 2. MEASURE INSTALLATION...................................................................................................................7 3. PREPARE THE INSTALLATION .............................................................................................................7 4. INSTALL BACKSPLASH ...........................................................
ページ4に含まれる内容の要旨
- NP60000 SERIES RANGE HOOD SYSTEM - INTERIOR BLOWERS Model 647 Model 634 or 644 Model 437 Model 441 (High capacity roof cap) (10’’ round wall cap) (7” round wall cap) (roof cap) Model 418 Model 415 (10” round adjustable elbow) (7” round adjustable elbow) Model 410 Model 407 (10” round duct—2 ft. sections) (7” round duct—2 ft. sections) Model 427 Model 423 Model 424 Model 454 Model 453 1 1 1 1 1 1 1 1 1 1 (4 /2” x 18 /2” (4 /2” x 18 /2” to (4 /2” x 18 /2” to (4 /2” x 18 /2” (4 /2” x 18 /2” to
ページ5に含まれる内容の要旨
- NP60000 SERIES RANGE HOOD SYSTEM - IN-LINE AND EXTERIOR BLOWERS Model 441 Model 437 Model HLB9 (800 cfm) (10” round wall cap) (High capacity roof cap) Model 335 (1200 cfm) or HLB11 (1100 cfm) or 336 (1500 cfm) in-line blower exterior blower Model 331H (600 cfm) (includes two 8” x 12” to or 332H (900 cfm) 10’’ round transitions) exterior blower Model 441 (10” Round wall cap) Model HLB6 (600 cfm) in-line blower (includes two 4 ½” x 18 ½” to 10’’ round transitions) Model 421 Model 418 (10” roun
ページ6に含まれる内容の要旨
1. SELECT BLOWER OPTION AND INSTALL DUCTWORK Either an interior or exterior blower or in-line blower may be used with this hood. The NuTone Premier 60000 Series must be installed with blower models RM325H, RM326H, HLB3, HLB6, HLB9, HLB11, 331H, 332H, 335 or 336 only. Other blowers cannot be substituted. (Blowers sold separately). NOTE: In addition to the blower models listed above, this hood is also compatible with older internal versions 325H and 326H. However, discard the installation instru
ページ7に含まれる内容の要旨
2. MEASURE INSTALLATION Dimensions for the most common installation are shown below. The minimum hood distance above cooktop must not be less than 24’’. A maximum of 30” above cooktop is highly recommended for best capture of cooking impurities. Distances over 30” are at the installer and users discretion. Standard 8 ft. (2.44 m) ceiling Standard 18" 18" (457 mm) H (457 mm) over-cooktop 19" cabinet (483 mm) Top of wood mounting strip Hood RMP Series Backsplash (optional) 24" (610 mm) Stan
ページ8に含まれる内容の要旨
4. INSTALL BACKSPLASH (OPTIONAL) (Optional) RMP Series Backsplash must be installed before the hood shell because the hood shell covers the backsplash top mounting screws. In order to be able to install the backsplash, make sure you have at least 18’’ clearance between bottom of hood and range control panel or cooktop. (See instructions packed with backsplash.) 5. INSTALL WOOD MOUNTING STRIP Measure and mark a level line on wall above cooktop location for the wood mounting strip (see illustratio
ページ9に含まれる内容の要旨
9. INSTALL THE ROUGH-IN PLATE TO THE HOOD (ALL BLOWERS) Run power cable to installation location. Refer to the instructions included with the selected blower or rough-in kit (sold separately) for details on 2 installing the rough-in plate. Install the rough-in plate so that the wiring 1 1 box is located on the right side as you are facing the hood. For ducting through back of hood, remove existing plate from inside 3 4 back of hood and attach it to inside top of hood to cover hole. Secure to 1 t
ページ10に含まれる内容の要旨
13. INSTALL LIGHT BULBS AND WARMING LAMPS Install (2) heat lamp bulbs. Use BR40 size, 250 W max., infrared bulbs only (sold separately). Install (3) halogen light bulbs. Use PAR20 size, 50 W (sold separately). 14. INSTALL FILTERS CAUTION Remove protective plastic film covering filters before installing them. It is recommended to install side filters first and finish with center one(s). 1. Insert upper end of filter into the hood (finger sized cup side). 2. Raise lower end toward the inside of ho
ページ11に含まれる内容の要旨
15. USE AND CARE 16. OPERATION Grease Filters Always turn ON your hood before you begin cooking in order to establish an air flow in the kitchen. Let the blower run The grease filters should be cleaned frequently. Use a for a few minutes to clear the air after you turn off the range. warm detergent solution. Grease filters are dishwasher This will help keep the whole kitchen cleaner and brighter. safe. Wash more often if your cooking style generates greater grease—like frying foods or wok cookin
ページ12に含まれる内容の要旨
17. SERVICE PARTS 19 20 18 16 17 10 13 21 15 2 19 11 3 5 12 4 7 14 6 6 9 1 8 1 HL0031 KEY PART QTY (HOOD WIDTH) NO. NUMBER DESCRIPTION 30’’ 36’’ 42’’ 48’’ 54’’ 60’’ 66’’ 72’’ 1 V02264 SOCKET LAMP 55 5 5 5 5 5 5 2 V02773 MALE CONNECTOR 11 1 1 1 1 1 1 3 V02772 FEMALE CONNECTOR 11 1 1 1 1 1 1 4 V03435 THERMOSTAT 11 1 1 1 1 1 1 5 V03436 THERMOSTAT BRACKET 11 1 1 1 1 1 1 6 V02563 SPST SINGLE SWITCH FOR WARMING LAMPS 22 2 2 2 2 2 2 7 V03502 SPST DOUBLE SWITCH FOR HALOGEN LAMP 11 1 1 1 1 1 1 8 V03503 S
