ページ1に含まれる内容の要旨
Warranty
Hunter Fan Company
Bath Exhaust Fan
LIMITED WARRANTY
Hunter Fan Company makes the following limited warranty to the original user or consumer purchaser of this Hunter bath
exhaust fan:
If any part of your Hunter bath exhaust fan (except for glass fixtures and light bulbs) fails at any time within one year after the date
of sale to you due to a defect in material or workmanship, we will repair or, at our option, replace the defective part free of charge
for parts and labor performed
ページ2に含まれる内容の要旨
Check all the parts. 95044-01-000 D W A R N I N G If damaged, call 95022-01-000 E 1-888-830-1326 TO REDUCE THE RISK OF ELECTRIC SHOCK OR INJURY, OBSERVE THE FOLLOWING: for replacements. 75190-01-000 such as those published by the National Fire Prevention 1. Use this unit only in a manner intended by the manufacturer. F Association (NFPA), and the American Society for Heating, If you have questions, contact the manufacturer at the phone 03242-07-133 Refrigeration and Air-Conditioning En
ページ3に含まれる内容の要旨
4 1 0 3 9 E C H B E Remove the motor/blower from the housing. Remove packing material. Pop out the first wiring access slug. Use second if needed. Insert the strain relief into the housing and secure with the washer. 5 6 Choose Installation Option For New Construction - attaching to joist go to step A11, page 5 For New Construction - suspended between joists go to step B11, page 8 For Existing Construction - accessible from above go to step C11, page 11 For Existing Construction - accessible on
ページ4に含まれる内容の要旨
O N O F F A 1 3 A 1 8 A 1 7 0 H Connect 4” duct and vent to the outside. Tape joints. Connect wiring from the motor to the wiring cover plate. Pull wires through the strain relief. If ducting does not fit securely, an adapter may need to be purchased. A 1 9 A 1 4 Ground A 2 0 Black Green 2 Pin Bare Copper White A Black Main Switch 1 (AC In) Fan Motor White White Night Light Red Night Light 3 Pin Light Black Light Red Switch 1 (AC In) *Option H I Black Switch 2 (AC In) *Option Fan & Main Ligh
ページ5に含まれる内容の要旨
A 2 3 B 1 5 B 1 6 Go to step E1 on page 18 to attach grille. Insert screws, leaving space between the screw Attach the rails onto the screws. head and the joist. Screws are not provided. New Construction – suspended between joists B 1 8 B 1 2 B11 B 1 7 D E 5/8 5/8 1/2 1/2 Pull wires through the strain relief. Position the correct depth mark at the bottom edge of Tighten screws. Slide the mounting rails into brackets. the joist based on the thickness of your sheetrock. B 1 3 B14 B 1 9 Grou
ページ6に含まれる内容の要旨
O N O F F B21 B20 B 2 6 B 2 7 F G • F Install the wiring cover plate. Make sure all Tighten the wiring cover plate screw. Test the motor. If the motor does not run, check the plug Turn on the power source. wiring connections are inside the box or under connection. the wiring cover plate. B 2 3 B 2 2 B 2 8 Go to step E1 on page 18 to attach grille. H Connect 4” duct and vent to the outside. Tape joints. Connect wiring from the motor to the wiring cover plate. If ducting does not fit securely, a
ページ7に含まれる内容の要旨
9” D C17 C12 C 1 8 E Cut out an opening for the housing. Slide the mounting rails into brackets. Attach the rails onto the screws. Tighten screws. C 1 3 C20 C 1 4 C 1 9 5/8 5/8 1/2 1/2 Position the correct depth mark at the bottom edge of the Mark position of screws by using holes as a template. Connect 4” duct and vent to the outside. Tape joints. Pull wires through the strain relief. joist based on the thickness of your sheetrock. If ducting does not fit securely, an adapter may need to be pu
ページ8に含まれる内容の要旨
O N O F F C 2 2 Ground C 2 8 C 2 7 Black Green 2 Pin Bare Copper White A Black Main Switch 1 (AC In) Fan Motor White White Night Light Red Night Light 3 Pin Light Black Light Red Switch 1 (AC In) *Option Black Switch 2 (AC In) *Option Fan & Main Light Together I Connect wires as shown. Secure the motor by tightening the 2 screws. Turn on the power source. C24 C23 C 3 0 C 2 9 F Go to step E1 G • on page 18 F to attach grille. Tighten the wiring cover plate screw. Install the wiring cover pla
ページ9に含まれる内容の要旨
D 1 3 D 1 8 D 1 4 D17 F G • F Attach existing ducting to duct connector. Tape joints. Install the wiring cover plate. Make sure all Tighten the wiring cover plate screw. Pull wires through strain relief. If ducting does not fit securely, wiring connections are inside the box or under an adapter may need to be purchased. the wiring cover plate. D 1 5 D 2 0 D 1 9 E H H Screw pre-loaded screws into joist or framing. Connect wiring from the motor to the wiring cover plate. Reinstall the motor by i
ページ10に含まれる内容の要旨
O N O F F D 2 3 D 2 4 E 6 E 5 Go to step E E E1 L on page 18 L to attach grille. Test the motor. If the motor does not run, check the plug Slide light base over posts in motor housing. Connect wiring harness. connection. Attaching the Grille E 2 E 7 E 8 E 1 N L L 2 M O 1 J Insert 1 Max 30 Watt CFL Pin Based Circline bulb (Included) Attach thumbscrews. Remove backs from 4 tape strips found on the trim disk. Rotate 4 metal clamps over glass trim. into spring clamps. WARNING: To reduce the risk
ページ11に含まれる内容の要旨
Trouble Shooting E 1 1 L Problem: Fan does not come on. Solution: • Hunter Fan Bath Ventilators are extremely quiet. To confirm that the fan is running, place your hand near the vents to feel the air movement. • Turn power on, replace fuse, or reset breaker. • Check all plug connections to be sure they are secure. • Check the wiring to make sure it matches the wiring diagram. N Problem: Light does not come on. Solution: • Replace the light bulb with a new bulb. Attach complete
